MICROCOM CORPORATION MODEL 470 DIRECT THERMAL / THERMAL TRANSFER PRINTER OPERATOR'S MANUAL Part Number 880010-0317 October 1995 Software Version 3.
Operator's Manual 470 Direct Thermal/Thermal Transfer Printer - Revised 10/10/95 MSG - Centronics is a registered trademark of Data Computer Corporation. Epson is a registered trademark of Seiko Epson Corporation. FX-86e is a trademark of Seiko Epson Corporation. HP and LaserJet II are trademarks of Hewlett-Packard Company. Comstar and I.D. Images are trademarks of Comstar Incorporated. FastFont is a trademark of Page Technology Marketing, Inc.
Table of Contents List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 CHAPTER 1: FEATURES AND SPECIFICATIONS . . . . . . . . . . . . . . .
Table of Contents )))))))))))))))))))))))))))))))))))))))))))) 4.5 4.4.1 A SAMPLE SESSION (HEADER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 LABEL FIELDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4.5.1 BIT MAPPED TEXT AND Bar code FIELDS . . . . . . . . . . . . . . . . . . . . 24 4.5.2 VECTOR FONTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.5.3 GRAPHIC IMAGE FIELDS . . . . . . . . . . . . .
Table of Contents )))))))))))))))))))))))))))))))))))))))))))) 10.3 CALCULATOR COMMANDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 CHAPTER 11: OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 11.1MICROCOM GRAPHICS CONVERSION UTILITIES . . . . . . . . . . . . . . . . . . . . . . 89 11.2 MICROCOM DOWNLOADABLE FONT UTILITY . . . . . . . . . . . . . . . . . . . . . . . 89 11.3 ADDITIONAL DOWNLOADABLE FONTS .
)))))))))))))))))))))))))))))))))))))))))))) 470 Operators Manual
List of Tables Serial Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Parallel Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Print Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Bitmapped Font Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
)))))))))))))))))))))))))))))))))))))))))))) 470 Operators Manual
Introduction The Microcom 470 is a Direct Thermal or Thermal Transfer label printer with a high resolution (832 dots or 8 dots/mm), 4.09 inch wide print head. Through the use of dual high speed processors, the printer has the ability to handle a wide variety of labeling tasks - even the most demanding applications. The resident Label Design Software (LDS) is a powerful and easy-to-use package that allows you to create personalized label formats.
)))))))))))))))))))))))))))))))))))))))))))) 2 470 Operators Manual
CHAPTER 1: FEATURES AND SPECIFICATIONS The Microcom 470 Direct Thermal/Thermal Transfer printer is designed with many standard features that are unique when compared to other printers. The 470 is built to meet the demands of complicated applications and rigorous use. A guarantee of excellence in engineering is provided by fulfilling the requirements for approval by UL, CSA and the FCC. 1.1 SPECIAL FEATURES ! Historical Dot Control provides increased print quality up to 4.5 ips.
Features and Specifications )))))))))))))))))))))))))))))))))))))))))))) Chapter 1 1.2 BAR CODES ! Code 39, Interleaved 2 of 5, CODABAR, Code 128, Code 93, Plessey, Modified Plessey, UPC-A, UPC-E, EAN-8, EAN-13, Postnet, and selectable ratios for producing HIBC, AIAG, and Logmars ! Bar codes may be printed in 0, 90, 180, and 270 degree rotations 1.
Chapter 1 )))))))))))))))))))))))))))))))))))))))))))) Features and Specifications 1.6 PHYSICAL ! Construction: Rigid painted steel with high impact molded front panel ! Height: 11.00" (279.4mm) ! Width: 10.125" (257.2mm) ! Depth: 10.10" (256.5mm) ! Weight: 35 LBS (15.89 K/g) 1.7 ENVIRONMENT ! Temperature: 0" C to 40" C operating ! Humidity: 10-90% non-condensing 1.8 ELECTRICAL ! Voltage: Switchable 100,110,120,220,240VAC nom., 50-60 Hz. ! Current: 3 Amps maximum (100VAC) 1.
Features and Specifications )))))))))))))))))))))))))))))))))))))))))))) Chapter 1 LEFT SIDE COVER PAPER SUPPLY LEFT SIDE FRONT PANEL DISPLAY PAPER SUPPLY HOLDER KEYPAD PAPER SUPPLY RACK RIGHT SIDE COVER RIBBON VIEW WINDOW PAPER SLOT RIGHT SIDE FRONT PANEL BACKING PAPER SLOT Microcom 470 Printer Front View Figure 1 RIGHT SIDE COVER LEFT SIDE COVER RACK THUMB SCREW PARALLEL PORT LEFT PAPER SUPPLY RACK SERIAL PORT PAPER SUPPLY HOLDER POWER SWITCH POWER ENTRY MODULE RIGHT PAPER SUPPLY RACK PO
CHAPTER 2: BASIC OPERATION 2.1 UNPACKING THE 470 PRINTER While unpacking the printer, please check all packing materials closely to avoid misplacing any necessary parts. After the printer is removed from the box, verify that all parts are present and in good condition (see Figure 3). All packaging material should be kept and used if the printer is to be shipped. The printer must be returned in the original container to insure proper warranty coverage. Printer Parts figure 3 2.
Basic Operation )))))))))))))))))))))))))))))))))))))))))))) Chapter 2 Keypad Layout Figure 4 2.4.1 PRINT/PAUSE KEY The front panel keypad (see Figure 4) contains a label 'PRINT/PAUSE' key. If this key is pressed the unit will print the currently loaded label format or the default label if no format has been loaded. If the printer is in the process of printing a predetermined quantity of labels (see ^D73, section 5.3), pressing the 'PRINT/PAUSE' key will pause the printer.
Chapter 2 )))))))))))))))))))))))))))))))))))))))))))) Basic Operation 2.4.3 ON-LINE KEY Pressing the 'ON-LINE' key causes the printer to suspend the processing of characters through the communication ports and display the message OFF-LINE. If a character is sent to the printer when communicating serially, the printer will accept the character and send an XOFF (assuming X-OFF has been enabled).
Basic Operation )))))))))))))))))))))))))))))))))))))))))))) 2.5 Chapter 2 MENU OPERATION General Operation Press to access the menu screen. Press or Press to accept current option. Press to exit/cancel current menu/option. Press to print current label. Press to advance paper and ribbon (if in transfer mode). to scroll through options. Variable Data Entry Press to input a 1. Press then to input an A. Press then then to input a B.
Chapter 2 )))))))))))))))))))))))))))))))))))))))))))) 2.6 Basic Operation LOADING MEDIA The following two sections explain the dispensing modes and printing methods. Refer to figures 2 and 5 for the printer components. If narrow stock is used (3.5 inches wide or less), it may be necessary to adjust the printhead support screw (see section 2.8). Thermal Transfer Note: The 470 will, on power-up, automatically sense a loaded ribbon and select thermal transfer mode.
Basic Operation )))))))))))))))))))))))))))))))))))))))))))) 2.7 Chapter 2 RIBBON SELECTION Many different ribbons can be used with the 470. However, to extend printhead life and achieve quality results, it is necessary to correctly match the ribbon to the receiver stock. Incorrect matching can cause premature printhead failure. Please contact Microcom concerning recommended media and compatibility. 2.8 PRINTHEAD SUPPORT ADJUSTMENT When using narrow media, less than 3.
CHAPTER 3: COMMUNICATIONS The 470 is very versatile. It can be interfaced to PC's, mini-computers, main frames, and special purpose machines. It is capable of serial RS-232-C, Centronics® parallel, and optionally RS-422/485 serial communication. The following sections explain the communication interfaces. Out of the box, unless otherwise requested, the Microcom 470 communicates using serial RS232-C at 9600 baud, 8 data bits, 1 stop bit and no parity with both hardware and software handshaking.
Communications )))))))))))))))))))))))))))))))))))))))))))) Chapter 3 Parallel Port Configuration 1 2 3 4 5 6 7 8 9 10 11 = = = = = = = = = = = /STROBE D0 D1 D2 D3 D4 D5 D6 D7 /ACK BUSY 12 13 14 15 16 17-18 19-30 31 32 33 34-36 = = = = = = = = = = = PAPER OUT SCLT NC NC LOGIC GND NC LOGIC GND /INIT /ERROR LOGIC GND NC (36 PIN CENTRONICS®) Table 2 3.
CHAPTER 4: DESIGNING LABELS USING LDS Label Design Software (LDS) refers to the software resident in the printer used to decipher label formats sent by the host computer. All fonts, character sets and bar codes symbologies are resident in the printer. A label format is produced by a series of 5 steps: 1: Control commands to define printer operation 2: A header to define label height, width, print speed, etc..
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) Chapter 4 Use the following DOS MODE command to set up the appropriate PC port. Note: COM1 may be any available communications port on your PC. C:>MODE COM1:9600,N,8,1,P You must then send the file to the printer using the following DOS command. C:>COPY FILENAME COM1 4.2.2 PC CONNECTION (PARALLEL) Items required: A computer with at least one unused parallel communications port. (LPT1,LPT2...) A parallel interface cable.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) Designing Labels Using LDS data section and contain information about positioning coordinates, the type of character generators or bar codes to use, etc.. Below is a sample label format. We will refer to this format as we break down the components of its structure.
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) Chapter 4 The sequence ^D575 puts the printer in format entry mode. The next line is the header information: sizing the label (812 dots wide 609 dots high). The next four lines are layout information for each data field in the format. The sequence ^D565 selects the user layout. The sequence ^D25 tells the printer to start accepting data for each defined field. (Field #1 defines where Data #1 should be positioned.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) Designing Labels Using LDS FEED DIRECTION OR 12 DOTS THIS IS THE WEB VALUE MICROCOM Y BEGINNING THIS IS 0,0 .
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) Chapter 4 Refer to Figure 7 for a visual representation of most header parameters. The following is a description of each header element: HFM NUMBER OF FIELDS IN LAYOUT This parameter is used to specify the number of fields in the layout. If more fields are defined than what is specified for HFM, the extras will be ignored.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) Designing Labels Using LDS Print Speed DPS VALUE MM PER SECOND INCHES PER SECOND INCHES PER MINUTE 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 203.2 200.7 198.1 195.6 193.0 190.5 188.0 185.4 182.9 180.3 177.8 175.3 172.7 170.2 167.6 165.1 162.6 160.0 157.5 154.9 152.4 149.9 147.3 144.8 142.2 139.7 137.2 134.6 132.1 129.
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) LCB Chapter 4 LABEL CONTROL BYTE This parameter selects between the various gap detection methods. Continuous Stock: If set to a value of 2, the printer will not activate the gap detector circuit. After all fields are printed, the printer will advance the extra distance in the SPG header element. Normal Stock (leading edge): If set to a value of 0, the printer will detect the leading edge of the label (the start of the next label).
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) Designing Labels Using LDS 4.4.1 A SAMPLE SESSION (HEADER) This is the label header from the sample label in section 4.3. 4,812,609,,20,48,,,5 5 5 4 - 4 fields following the header 812 - Label width (LSX) of 812 (812/203 = 4 inches). 609 - Label length (LSY) of 406 (609/203 = 3 inches). - The WEB parameter can be defaulted. 20 - A GAP between labels of 20 48 - Label print speed (DPS) of 48 = 3.
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) 4.5 Chapter 4 LABEL FIELDS A field is broken down into many different parameters. These parameters contain the information necessary to position data (text, bar codes, graphics, etc.) on the label. It is not necessary to enter values for all of the field parameters; the default values will be used if left blank. The fields to be defaulted must be separated by commas. A carriage return must follow each label field. 4.5.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) Designing Labels Using LDS CC CHARACTER COUNT This parameter determines the number of characters that will be used in a field. If the number of characters in the selected text string is more than the quantity specified by CC, then the remainder of the text string is ignored. If the text string has less than the number of characters specified by this parameter, then only those characters defined by the text string are printed.
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) CGN Chapter 4 CHARACTER GENERATOR NUMBER This refers to the character generator (font size, bar code size, etc.) that is used. The generator numbers and the specifications for the various fonts, bar codes, and graphics are shown below. Remember, there are 203 dots per inch.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) Designing Labels Using LDS Table 5 constitutes the bar codes available on the 470 printer. Some bar codes offer different ratios to accommodate different applications. See Section 7.1 for more information on designing with bar codes.
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) Chapter 4 Starting position definitions: Table 6 shows how to obtain proper character placement relative to orientations and justifications.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) Designing Labels Using LDS TSP TEXT STARTING POSITION This parameter marks the starting position of the character in the text string to be used as data. This is useful for allowing several fields to use sections of the same text string, minimizing the amount of data transmitted. For example, for the text string 0123456789, A TSP of 5 and a CC (character count) of 2 would print 45. See section 5.3.4 for use of this parameter with clock fields.
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) 4.5.2 Chapter 4 VECTOR FONTS The following is a list of vector font field element mnemonics and their default values: TSN, XB, YB, CC,TCI,CGN, FO, FJ, CWX,CWY, CS, TSP, AN,STK 1, 0, 0, 1, 4, 1, 0, 0, 0, 0, *, 1, 0, 1 * The default depends on the size of the characters (CWX,CWY). Note: All values must be positive integers. TSN TEXT STRING NUMBER This parameter determines from which text string the field obtains the data.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) CGN Designing Labels Using LDS CHARACTER GENERATOR NUMBER The generator numbers and specifications are shown below. Vector Font Descriptions CGN 1 2 Font Type Standard ASCII (characters up to 7F hex) Extended ASCII (characters up to FF hex) Table 8 FO FIELD ORIENTATION This parameter defines field rotation and has a value between 0 and 359. A value of 0 is normal and a value of 180 is upside down.
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) Chapter 4 TSP TEXT STARTING POSITION This parameter marks the starting position of the character in the text string to be used as data. This is useful for allowing several fields to use sections of the same text string minimizing the amount of data transmitted. For example, for the text string 0123456789 A TSP of 5 and a CC (character count) of 2 would print 45. See section 5.3.4 for use of this parameter with clock fields.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) 4.5.3 Designing Labels Using LDS GRAPHIC IMAGE FIELDS A graphic field is broken down into six different parameters. The first two are the start coordinates, the next two control the image size. If the image size is omitted, the image printed will represent a true proportioned image. If not, the printed image will be stretched/compressed to "fit in frame".
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) Chapter 4 CGN CHARACTER GENERATOR NUMBER This value selects the stored graphic image to be printed (0-16). AN ATTRIBUTE NUMBER If this parameter is set to a value of 2, the field can be printed white on black. A value of 0 is normal. Sample Format File to Access Stored Graphic Images The following format will illustrate the use of a graphic image field.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) 4.5.4 Designing Labels Using LDS LINES A line field is broken down into six different parameters. The first two are the start coordinates, the next two are the end coordinates. The fields to be defaulted must be separated by commas, and a carriage return must follow each graphics field definition.
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) WID Chapter 4 PEN WIDTH This parameter will set the width of the pen used to draw the line.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) 4.5.5 Designing Labels Using LDS FILLED RECTANGLE A filled rectangle field is broken down into five different parameters. The first two are the start coordinates, the next two are the length and width. The fields to be defaulted must be separated by commas and a carriage return must follow each graphic field definition.
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) 4.5.6 Chapter 4 FILLED OVAL A filled oval field is broken down into five different parameters. The first two mark the center point, the next two define the radius width (X) and height (Y). The fields to be defaulted must be separated by commas and a carriage return must follow each field definition.
Chapter 4 )))))))))))))))))))))))))))))))))))))))))))) 4.5.7 Designing Labels Using LDS FRAMED OVAL A framed oval field is broken down into seven different parameters. The first two mark the center point, the next two define the radius width (X) and height (Y), and the last two set the frame width and height. The fields to be defaulted must be separated by commas and a carriage return must follow each field definition.
Designing Labels Using LDS )))))))))))))))))))))))))))))))))))))))))))) 4.5.8 Chapter 4 A SAMPLE SESSION (FIELDS) Looking at the sample label...
CHAPTER 5: PRINTER COMMANDS The 470 printer has a large and versatile collection of command codes to meet the special needs of labeling applications. Most of the commands use a ^D control sequence, however the printer also recognizes a selected number of other control sequences. For all the commands listed in this manual, the 470 will recognize either the one-character control character or the two-character caret and alpha character sequence.
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) Chapter 5 ^M Terminate Text or Data String: Must be used to terminate a text or data string. (Same as a carriage return or enter key on computer keyboard) ^H Deletes The Last Printable Character Entered: This is used only when communicating to the printer through the keyboard. (Same as Delete key on computer keyboard.) ^K Print Test Label: A test label consists of a series of diagonal lines.
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) 5.3 Printer Commands SENDING ^D PRINTER COMMANDS Unless otherwise specified, these commands are entered by sending a ^DXX, where XX is the command number. It is followed by a carriage return or another control code. Some commands load data or control numbers and are preceded by a ^AXX, where XX represents the data or control number. Unless otherwise specified, command codes should appear first in the label format, if a label format is being sent.
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) ^A ^D 21 Chapter 5 Command Change SW1: Software dip switch #1. The dip switches are the only commands that use binary input. They can use a ^AB sequence followed by an 8 digit 0 or 1 code. For example: ^AB10000011^D215 will configure the printer for a text equivalent enquiry response, accept control codes, scanner input off, disable displayed enquiry, disable echo, 8 data bits, and enable XON/XOFF flow control. 12345678 ^ABxxxxxxxx *******.
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) ^A ^D 22 Printer Commands Command Change SW2: Software dip switch #2. Below is the ^AB sequence: 12345678 ^ABxxxxxxxx *******.)))), ******.)))),* *****.
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) ^A ^D 23 Chapter 5 Command Change SW3: Software dip switch #3. Below is the ^AB sequence: 12345678 ^ABxxxxxxxx *******. ******.) *****.)) ****.))) ***.)))) **.))))) *.)))))) .
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) ^A ^D 24 Printer Commands Command Change SW4: Change software dip switch #4. Below is the ^AB sequence: 12345678 ^ABxxxxxxxx *******.) ******.)) *****.))) ****.)))) ***.))))) **.)))))) *.))))))) .
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) ^A ^D 25 Chapter 5 Command Change SW5: Change software dip switch #5. Below is the ^AB sequence: 12345678 ^ABxxxxxxxx *******.) ******.)) *****.))) ****.)))) ***.))))) **.)))))) *.))))))) .
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) Printer Commands ^A XX ^D 36 Command Adjust Contrast Base: Use this command to adjust/calibrate the default contrast. Since the non-permanent ^D35 command is used to control the darkness in a format file, the ^D36 command is offered to correct any contrast differences that may exist between different printers while using the same format file. This command is non-volatile and only needs to be sent once.
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) Chapter 5 ^A XX ^D 75 Command Load Label Count: Tells the printer to print a batch of labels using the serial number function if enabled. Can be used in conjunction with load copies count (^D73). The batch of labels will be printed when a ^D35 is executed. Therefore, this must precede a ^D3 command. The only difference between this command and ^D73 is in the ability of this command to increment and decrement sequential numbers in the batch.
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) ^A ^D 39 0 1 2 3 XX 91 Printer Commands Command Autosize Label: Clears the use of autosize values set by ^A1^D395. Uses the values obtained for the variables above instead of what the user supplies in the header of the file format. This will not display the variables on the screen. Automatically sizes the label and displays on the screen the values for the size variables. These values should be placed in the label header for that stock.
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) 5.3.
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) Printer Commands A sample program using the clock function: ^D575 2,,6095 0,320,40,8,16,2,,4,2,60,,105 0,320,20,8,1,10,,4,,,,105 ^D565 ^D35 ^D575 3,,6095 0,320,40,12,16,2,,4,2,60,2,235 0,320,20,12,1,10,,4,,,,235 1,320,110,20,1,11,,45 ^D565 ^D25 EUROPEAN DATE FORMAT5 ^D35 ^D575 3,,6095 0,320,40,12,16,2,,4,2,60,2,105 0,320,20,12,1,10,,4,,,,105 1,320,110,20,1,11,,45 ^D565 ^D25 US DATE FORMAT5 ^D35 ^D575 3,,6095 0,320,20,34,1,10,,45 0,550,80,8,1,10,3,4
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) Chapter 5 5.3.5 SERIAL NUMBER COMMANDS The following commands, ^D80 through ^D89, refer to the serial numbering functions of the 470 printer. The 470 can increment or decrement any single serial number by any amount. ^A ^D 80 Command Disable all serial numbering. XX 81 Disable Single Serial Number Field: Will disable an individual serial number field.
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) ^A XX ^D 75 Printer Commands Command Load Label Count: Tells the printer to print a batch of labels using the serial number function if enabled. Can be used in conjunction with load copies count (^D73, see section 5.3). The batch of labels will be printed when a ^D3 is executed. Therefore, this must precede a ^D3 command.
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) 5.3.6 Chapter 5 LABEL HEADER COMMANDS The following ^D commands, 41 - 51, all refer to label header values. They are provided to allow single element modification without having to send the entire label header. The printer will use these values for all subsequent label formats unless a ^D40 is executed, the machine is powered off, or a replacement value is sent or included in a new label header.
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) Printer Commands XX 50 Load X direction offset (OFX): ^A indicates the X offset. XX 51 Load Y direction offset (OFY): ^A denotes the Y offset. 5.3.7 SAVED FORMAT FILE COMMANDS The printer has the capability to store format files to RAM without processing them. Later, these format files can be accessed repeatedly at very high speeds, because access to the formats are now a direct memory fetch.
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) Chapter 5 information with all the fixed text data. Terminate the file with an ESCAPE character. Now the variable data may serially be sent to the file. It may be the difference between sending two lines of data versus the full 120 lines of the file! Access is very fast. To read a file that has previously been sent to the printer, use the ^AX^D545 command, where ^AX denotes the file (slot #) to be read.
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) Printer Commands File #2 ^A1^D585 ^D25 24 PRINTS $ 3.79 204963403795 ^D35 File #3 ^A2^D595 "sample 2" ^D575 4,620,161,,18,35,,73,35 1,120,110,50,1,115 2,120, 80,70,1,105 3,120, 60,70,1,105 4,120, 40,70,1,105 ^D565 File #4 ^A2^D585 ^D25 MICROCOM CORPORATION5 8333-A GREEN MEADOWS DR., N.
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) Chapter 5 5.3.8 LABEL PRESENCE SENSOR CONTROL The label presence sensor instructs the printer to dispense labels at the operators pace. If a label has been printed but not removed, the printer will wait until the label is removed before allowing another label to be printed. The following modes define its operation.
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) ^A ^D 98 Printer Commands Command Peel-and-Dispense Mode: A method of dispensing a label, where the backing paper is automatically peeled away from the label. It allows the operator to take the label and apply it to an object without having to peel the label off the backing paper. The printer will advance the label so that it is still hanging off the tear bar. This will make it easier for the operator to take the label.
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) Chapter 5 The printer would automatically update the new bar code with the two fixed numbers. ^D625 protects existing text and appends new text. A ^D625 prevents existing text lines from being over-written. Any new text entered after a ^D25 will be appended to the existing lines. 63 0 1 Disable 1 & 2. Enable auto-print mode: New text entered after this command are recognized as text lines and will overwrite existing text.
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) Printer Commands This is an example of the D63, 64 and 65 Commands...
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) Chapter 5 5.3.10 MISCELLANEOUS PRINTER COMMANDS ^A 0 1 2 3 ^D 2 Command Text string entry mode: Begin text entry mode. This command must be sent before the printer will accept text or bar code information. (Equivalent to ^B) 5 Send Printer Status: See section 5.3 (Equivalent to ^E) 29 Printer Statistics: ^A selects the mode.
Chapter 5 )))))))))))))))))))))))))))))))))))))))))))) ^A 1 2 Printer Commands ^D 32 Command Reset Machine: Restores printer to power-up settings. 33 Display Model and Revision Number: Displays important reference numbers. 35 Contrast Window Adjust: Adjusts to a percentage of current contrast base. Used for temporary variations in paper and should be lowered for ladder style (vertical) bar codes. This command should be placed directly before the ^D57 command in a format file.
Printer Commands )))))))))))))))))))))))))))))))))))))))))))) ^A XX 0 1 Chapter 5 ^D 55 Command Select Default Label Layout: Select from the ROM power-up label layout. Only used if you have a special lay-out burned into the ROM by Microcom. ^A selects which one (1-8), if more than one are present. 56 End User Defined Field Definitions: Tells the printer that all field definitions are complete.
CHAPTER 6: LOADING GRAPHIC IMAGES The Microcom 470 printer is capable of storing multiple graphic images. You may either use the Microcom "PCX2470" software to create a PGS or PGV file from a PCX or PCC file, or use your own software to format a graphics file into a form that the printer can understand. METHOD #1: Create your own software to manipulate graphic files into the 470 format. METHOD #2: Use the "PCX2470" software to turn your PCX file into the 470 format.
Loading Graphic Images )))))))))))))))))))))))))))))))))))))))))))) Run Length White Code Black Code Chapter 6 Run Length White Code Black Code 0 00110101 0000110111 32 00010011 000001101010 1 000111 010 33 00010010 000001101011 2 0111 11 34 00010011 000011010010 3 1000 10 35 00010100 000011010011 4 1011 011 36 00010101 000011010100 5 1100 0011 37 00010110 000011010101 6 1110 0010 38 00010111 000011010110 7 1111 00011 39 00101000 000011010111 8 10011
Chapter 6 )))))))))))))))))))))))))))))))))))))))))))) Run Length White Code Black Code Loading Graphic Images Run Length White Code Black Code 64 11011 0000001111 1344 011011010 0000001010011 128 10010 000011001000 1408 011011011 0000001010100 192 010111 000011001001 1472 010011000 0000001010101 256 0110111 000001011011 1536 010011001 0000001011010 320 00110110 000000110011 1600 010011010 0000001011011 384 00110111 000000110100 1664 011000 0000001100100 448 01100
Loading Graphic Images )))))))))))))))))))))))))))))))))))))))))))) 6.3 Chapter 6 GRAPHIC IMAGE COMMAND SUMMARY The following commands refer to the use of graphic images: ^A XX ^D 71 Command Clear Single Non-Volatile Graphic Image from Non-Volatile User Memory: This command will clear a single non-volatile saved graphic file (1-16) and open the slot for a new graphic. XX 101 Load Graphic Image into Non-Volatile User Memory: ^A select which volatile slot to place the image in (1-16).
CHAPTER 7: BAR CODES Although bar codes are accessed in the same manner as text fields, bar codes often limit or expand the type of data that can be used. The purpose of this chapter is to explain and eliminate many of the questions that surface when dealing with bar codes for the first time. 7.1 TYPES OF BAR CODES Universal Product Code - Version A (UPC-A), TCI=12 The UPC-A bar code is primarily used in the supermarket industry. It contains 11 numeric data characters and a single numeric check digit.
Barcodes )))))))))))))))))))))))))))))))))))))))))))) Chapter 7 Universal Product Code - Version E (UPC-E, send 7 digits), TCI=13 TCI 13 is the same as TCI 12 except that only the actual 7 numeric digits are used to produce the bar code. European Article Numbering System - Version 13 (EAN-13), TCI=20 EAN-13 is not generally used in the United States. It contains 13 digits and is constructed in the same manner as UPC-A.
Chapter 7 )))))))))))))))))))))))))))))))))))))))))))) Barcodes Code 128 Special Function Access # Value CODE A CODE B CODE C #0 96 FNC3 FNC3 ----- #1 97 FNC2 FNC2 ----- #2 98 SHIFT SHIFT ----- #3 99 CODE C CODE C ----- #4 100 CODE B FNC4 CODE B #5 101 FNC4 CODE A CODE A #6 102 FNC1 FNC1 FNC1 #7 103 START ----- ----- #8 104 ----- START ----- #9 105 ----- ----- START ## 3 # # ----- Table 13 For example: The UCC-128 shipping container specificatio
Barcodes )))))))))))))))))))))))))))))))))))))))))))) Chapter 7 AS-10, TCI=44 AS-10 is not widely used. It is variable length and encodes the numeric values 1234567890 only. 7.2 DESIGNING WITH BAR CODES When 0 and 180 degree bar codes are X multiplied (CMX), the space between characters is also multiplied to maintain the correct ratios. The printer will do this internally. Therefore, when multiplying bar codes, use the default value for the spacing element (SP) in the field parameters.
Chapter 7 )))))))))))))))))))))))))))))))))))))))))))) Barcodes 7.2.1 BAR CODE HUMAN READABLES Text conversion identifiers (TCI position in field description) 32 and 33 refer to the human readable portion of UPC-A bar codes. They are designed to be used in conjunction with UPCA bar codes, They only create the text equivalent of the UPC-A bar code and optionally add the extended portions of the bar code lines. This lower portion must them be lined up with the upper to create a correct UPC-A bar code.
Barcodes )))))))))))))))))))))))))))))))))))))))))))) Chapter 7 UPC-A HR W/O CHKSUM5 012345678905 EAN13 0123456789015 EAN8 01234565 UPC-E 001234000055 UPC-E 101234000055 ^D35 )))))))))))))))))))))))))))))))))))))))))))) 76 470 Operators Manual
CHAPTER 8: SPECIAL EFFECTS 8.1 REVERSED PRINT (WHITE TEXT OVER BLACK) The 470 has the ability to print white text on a user definable black background. The black background can be automatically added by using an AN of 4. If this method is used, the size of the black background will automatically be adjusted to match the amount of text entered. The amount of bottom border can be increased by sending the ^AXXX^D139 command (XXX = 0 to 255 dots).
Soft Fonts )))))))))))))))))))))))))))))))))))))))))))) Chapter 9 Program sample: Reverse Imaging (See Figure 14) ^A75^D95^A1^D985 ^D575 12,831,1350,,,415 1,20,780,9,4,1,0,0,90,100,9,1,0,205 ;Normal field using 20dot wide pen 1,20,780,9,4,1,0,0,90,100,9,1,2,155 ;Overprint above with 15dot pen and AN=2 1,20,630,9,4,1,0,0,90,100,9,1,0,205 ;Use the same method as above to 1,20,630,9,4,1,0,0,90,100,9,1,2,105 ;print the remaining hollow and shadow 1,20,480,9,4,1,0,0,90,100,9,1,0,205 ;fields (Note: shadowed fie
CHAPTER 9: DOWNLOADABLE FONTS The 470 is capable of storing up to 8 downloadable fonts in non-volatile user memory (192KB) and up to 16 downloadable fonts in volatile DRAM (320KB). The printer treats downloadable fonts just like the standard bit mapped fonts mentioned in chapter 4.5.1. Since the printer has the ability to rotate characters, only the Portrait or 0 degree rotation is required. You may either purchase downloadable fonts from Microcom (see section 11.
Soft Fonts )))))))))))))))))))))))))))))))))))))))))))) ^A ^D 118 0 1 2 9.2 Command Read Volatile User Memory: The 470 will send the contents of the volatile (320KB) user memory to the serial port. List volatile graphic images and downloadable fonts List volatile graphic images List volatile downloadable fonts 119 0 1 2 3 Chapter 9 Read Non-Volatile User Memory: The 470 will send the contents of nonvolatile 192KB user memory to the serial port.
Chapter 9 )))))))))))))))))))))))))))))))))))))))))))) Default Char - byte Filler LLC - byte word NonPropOff - word Soft Fonts Default character to be imaged if character code is less than first character or larger than last character Always 0 Offset to the first character tier, from the start of the first character in words. This is the lower left hand corner of the first character. This pier is the ((cell height-1) * pier size) Offset, in words, to the non-proportional character pointer table.
Soft Fonts )))))))))))))))))))))))))))))))))))))))))))) Chapter 9 Sample 'C' structure of a Microcom Downloadable Font /* Microcom Downloadable Font Structure */ /* header data */ typedef struct _Mic_ras { char font_name_2[18]; /* font name surrounded by asterisk's */ unsigned short size_of; /* number of words following */ unsigned char first_char; /* first character in font */ unsigned char last_char; /* last character in font */ unsigned short pitch; /* pitch of packed characters */ unsigned short cell_
CHAPTER 10: PROMPTING To expand the versatility of the 470 printer, Microcom has added self prompting to the list of features. The prompting software can be configured to run through a preset series of prompts (Buffer Mode), or it can be controlled by a host computer (Slave Mode). The following sections explain how to use these two modes. PROMPTING ARCHITECTURE: To Increase the versatility of the 470, text segments and a operational buffer have been added. Text segments are strings of 32 or less characters.
Prompting )))))))))))))))))))))))))))))))))))))))))))) Chapter 10 Since all transfers to fields are appends, it may be necessary to clear field data prior to a transfer. ^A ^D 148 Command Clear Operational Buffer Data: 149 Clear Field Data: 150 Clear Text Segment Data: 10.2 PROMPTING COMMANDS ^A XX... ^D 120 Command Load Prompt Control Word #1: XX is the data for the prompt status word. The format is ^AB1111111111111111^D1205. XX...
Chapter 10 )))))))))))))))))))))))))))))))))))))))))))) Prompting Commands ^D120 and ^D124 refer to status words. The following is a breakdown of the two status words. STATUS WORD #1: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ^ABxxxxxxxxxxxxxxxx ***************. **************.) *************.)) ************.))) ***********.)))) **********.))))) *********.)))))) ********.))))))) *******.)))))))) ******.))))))))) *****.)))))))))) ****.))))))))))) ***.)))))))))))) **.))))))))))))) *.)))))))))))))) .
Prompting )))))))))))))))))))))))))))))))))))))))))))) Keyboard SHIFT, SHIFT, SHIFT, CLEAR - Chapter 10 Clears current text in 2nd line of display Miscellaneous Notes: There is a 40 character text limit on keyboard entry. The label field character count should be set to match the largest field. 10.3 CALCULATOR COMMANDS All Calculator functions are performed on the operational buffer. Legitimate input are floating point strings with up to 9 digit whole numbers and 9 digit fractions.
Chapter 10 )))))))))))))))))))))))))))))))))))))))))))) Prompting 'X', in all cases, specifies whether the operation is performed on a text segment (1) or a field (0). Additional commands control the format of the output data. The following operations are performed on the operational buffer. ^A X ^D 153 Command Round/Expand Floating Point Fraction: This command will round or expand the Floating Point Fraction to the desired number of decimal places.
Prompting )))))))))))))))))))))))))))))))))))))))))))) Chapter 10 Program sample: Prompting (See Figure 15) ^A7^d1235 ;Set the number of passes to 7 ^D575 ;Set up normal label... 4,831,600,,18,505 1,60,320,50,4,,,,15,40,8,,,55 2,60,260,50,4,,,,15,40,8,,,55 3,60,200,50,4,,,,15,40,8,,,55 3,60, 80,50,365 ^D565 ^D25 ;Begin text entry MICROCOM CORPORATION5 ;Text field 1 8333-A GREEN MEADOWS DR., N.
CHAPTER 11: OPTIONS The 470 printer has many options available to enhance the performance of the printer. Contact your sales representative for more information on these features. 11.1MICROCOM GRAPHICS CONVERSION UTILITIES PCX2470.EXE This PC software program decodes PCX files and converts them to the Microcom 470 format which can be stored in the 470 printer. It supports all 470 graphics features. See chapter 4.5.3 and 6 for more information about printing graphic images. PCX2BIT.
APPENDIX A: WARRANTY AND REPAIR PROCEDURES LIMITED WARRANTY A Microcom cleaning kit must be purchased with each printer to validate warranty. For a period of 12 months Microcom warrants its products against defects in materials and workmanship. The thermal print head is warranted for a period of three months or 500,000 linear inches to be free from defects in material of workmanship. Determination of such print head failure shall be determined by the print head manufacturer or Microcom.
APPENDIX B: LABEL SAMPLES POWER-UP ^D575 43,808,592,20,10,48,0,1,5355 1, 45, 38,19,16,3, 0,0, 2,705 1,170, 10,19, 4,1, 0,0,20,20,5,1,0,45 2,744,350, 8,15,3,270,1, 3,805 2,772,355, 8, 4,1,270,0,20,20,4,1,0,45 3, 50,245,10, 4,1, 0,0,36,50,5,1,0,85 4,105,180,10, 4,1, 0,0,70,50,7,1,0,75 5, 75,530,19, 4,1, 0,0,12,17,2,1,0,35 6, 98,505,19, 4,1, 31,0,12,17,2,1,0,35 7, 69,478,19, 4,1, 58,0,12,17,2,1,0,35 8, 46,510,19, 4,1, 90,0,12,17,2,1,0,35 9,420,240,19, 4,1,180,0,23,45,4,1,1,35 9,420,238,19, 4,1, 0,0,23,45,4,1,0
Label Samples )))))))))))))))))))))))))))))))))))))))))))) Appendix B LINES ^D575 29,800,600,,,16,0,,560,0,05 1,200,450,11,4, 1,0,0,27,30,3,1,0,55 2,200,290,12,4, 1,0,0,27,30,3,1,0,55 3,200, 50,14,4, 1,0,0,27,30,3,1,0,55 4,677,518, 1,1,14,0,0, 1, 1,1,1,05 5,730,403, 1,1,14,0,0, 1, 1,1,1,05 6,730,323, 1,1,14,0,0, 1, 1,1,1,05 7,730,243, 1,1,14,0,0, 1, 1,1,1,05 8,680,462, 1,1,14,0,0, 1, 1,1,1,05 9,680,403, 1,1,14,0,0, 1, 1,1,1,05 10,680,343, 1,1,14,0,0, 1, 1,1,1,05 11,680,283, 1,1,14,0,0, 1, 1,1,1,05 12,680,
Appendix B )))))))))))))))))))))))))))))))))))))))))))) Label Samples ^D35 ^D575 3,800,200,,,18,0,, 80, 0,05 1,300,25, 6, 4, 1,0,0,27,30,3,1,0,55 2,243,90,13,20, 2,0,0, 3,805 2,281,65,13, 1,10,0,0, 1, 15 ^D56^D25 EAN-135 12345678912345 ^D35 ^D575 3,800,200,,,18,0,, 80,0,05 1,287,26,7, 4, 1,0,0,27,30,3,1,0,55 2,164,92,9,42, 3,0,0, 3,80,35 2,309,68,9, 1,10,0,0, 1, 15 ^D56^D25 CODABAR5 1234567895 ^D35 ^D575 3,800,200,,,18,0,, 80,0,05 1,290, 30,7, 4, 1,0,0,27,30,3,1,0,55 2,205,100,9,43, 2,0,0, 3,805 2,317, 71
Label Samples )))))))))))))))))))))))))))))))))))))))))))) Appendix B ^D575 3,800,200,,,18,0,, 80,0,05 1,290, 38, 5, 4,1,0,0,27,30,3,1,0,55 2,218,100,11,12,2,0,0, 3,805 2,185, 81,11,32,2,0,0, 3, 25 ^D56^D25 UPC-A5 1234567890125 ^D35 ^D575 3,800,200,,,18,0,, 80,0,05 1,290, 28, 5, 4, 1,0,0,27,30,3,1,0,55 2,280,100, ,13, 2,0,0, 3,805 3,290, 71,11, 1,10,0,0, 1, 15 ^D56^D25 UPC-E5 070402000085 07040285 ^D35 ^D575 3,800,200,,,18,0,, 80,0,05 1,290, 28, 5, 4, 1,0,0,27,30,3,1,0,55 2,201,100,11,44, 2,0,0, 3,805 2,2
Appendix B )))))))))))))))))))))))))))))))))))))))))))) Label Samples REVERSED PRINTING ^D575 11,800,600,,,31,0,,560,0,05 494,530,284,530,6,605 133,230,133,454,6,605 355,389,125,175,95 685,218,685,476,6,605 504,133,268,133,6,605 1,240,483,8,1,14, 0,0,1,1,1,1,25 2,640,443,8,1,14, 90,0,1,1,1,1,25 3,117,198,8,1,14,270,0,1,1,1,1,25 4,482,120,8,1,14,180,0,1,1,1,1,25 5,240,325,7,1,11, 0,0,2,2,2,1,25 6,280,245,5,1,11, 0,0,2,2,2,1,25 ^D56^D25 MICROCOM5 Microcom5 Microcom5 MICROCOM5 REVERSE5 VIDEO5 ^D35 ROTATIONS
Label Samples )))))))))))))))))))))))))))))))))))))))))))) FONT FONT FONT FONT FONT FONT FONT FONT FONT FONT FONT FONT FONT ^D35 3: 4: 5: 6: 7: 8: 9: 10: 11: 12: 13: 14: 19: Appendix B 6X55 7X55 7X75 7X75 8X55 9X55 9X75 12X85 15X125 18X105 40X155 40X205 OCR A5 ^D575 5,620,4415 1,100, 40,12, 5,100, 62, 3, 4,100, 84, 3, 3,100,106, 3, 2,100,128, 3, ^D565 ^D25 X MULTIPLIER5 1X5 2X5 4X5 8X5 ^D35 ^D575 5,620,4415 1,100, 40,12, 5,100, 62, 3, 4,100,168, 3, 3,100,226, 3, 2,100,260, 3, ^D565 ^D25 Y MULTIPLIER5 1Y
Appendix B )))))))))))))))))))))))))))))))))))))))))))) Label Samples ^D575 5,620,4415 1,100, 40,14, 1,105 5,100, 62, 3, 1,10,,,8,85 4,100,168, 3, 1,10,,,4,45 3,100,226, 3, 1,10,,,2,25 2,100,260, 3, 1,105 ^D565 ^D25 XY MULTIPLIER5 1XY5 2XY5 4XY5 8XY5 ^D35 ^D575 4,620,4415 4, 50,100,23,1,10,,,,,205 3, 50,122,23,1,10,,,,,105 2, 50,144,23,1,10,,,,, 55 1, 50,166,23,1,10,,,,, 15 ^D565 ^D25 CHARACTER SPACING 15 CHARACTER SPACING 55 CHARACTER SPACING 105 CHARACTER SPACING 205 ^D35 ^D575 9,620,4415 1,320, 30,11,
Label Samples )))))))))))))))))))))))))))))))))))))))))))) Appendix B ^D575 1,620,441,,,,,,,,1005 1,100,100,15,1,135 ^D565 ^D25 Y OFFSET OF 1005 ^D35 )))))))))))))))))))))))))))))))))))))))))))) 98 470 Operators Manual
APPENDIX C: SAMPLE BASIC PROGRAM This Basic program produces labels for computer diskettes. It is intended to show the simplicity that higher languages communicate with the 470 printer. Communication parameters may need to be changed for some computers.
APPENDIX D: QUICK REFERENCE COMMAND SUMMARY The following is a list of HEADER element mnemonics and their default values: HFM, LSX, LSY, WEB, GAP, DPS, LCB, AGD, SPG, OFX, OFY 0, 832, 443, 10, 10, 48, 0, 1, 535, 0, 0 The following is a list of BIT MAPPED field mnemonics and their default values: TSN, XB, YB, CC,TCI,CGN, FO, FJ, CMX,CMY, CS,TSP, AN, PS 1, 0, 0, *, 1, **, 0, 0, 1, 1, *, 1, 0, 0 The following is a list of VECTOR font field mnemonics and their default values: TSN, XB, YB, CC,TCI,CGN, FO, F
Appendix D )))))))))))))))))))))))))))))))))))))))))))) Quick Reference Command Summary The following is a combined list of all TCI (Text Conversion Identifier) numbers: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 *17 18 19 20 21 *22 *23 24 25 26 *28 *29 *32 *33 36 40 41 42 43 44 Text Text Surrounded by Asterisks (Code 3 of 9) Text with UPC-A/UPC-E Checksum Digit Printed Vector Text Round Line Square Line Graphics (ROM and RAM) Non-Volatile downloadable fonts Fill Rectangle Volatile Graphics Volatile downloa
Quick Reference Command Summary )))))))))))))))))))))))))))))))))))))))))))) ^A Appendix D ^D 2 Command Text string entry mode: Precedes the text strings that are supplied to the various fields in the label (Equivalent to ^B). 3 Print Command: Prints a single label or starts the printing of a batch of labels.
Appendix D )))))))))))))))))))))))))))))))))))))))))))) 22 Quick Reference Command Summary Change SW2: Software dip switch #2. Below is the ^AB sequence: 12345678 ^ABxxxxxxxx *******.)))), ******.)))),* *****.
Quick Reference Command Summary )))))))))))))))))))))))))))))))))))))))))))) 25 Appendix D Change SW5: Software dip switch #5. Below is the ^AB sequence. 12345678 ^ABxxxxxxxx *******.) ******.)) *****.))) ****.)))) ***.))))) **.)))))) *.))))))) .)))))))) 26 Not Used 1=Enable Auto Error Message Transmission Not Used Not Used Auto Adjust for Black Line Darkness Not Used Not Used 1=Disable Name/Time When Idle, 0=Enable Change SW6: Software dip switch #6. Below is the ^AB sequence.
Appendix D )))))))))))))))))))))))))))))))))))))))))))) 28 Show Head Size: This function will send the print head dot count to the communications port. The output is in standard ASCII and will be 640, 768, or 832.
Quick Reference Command Summary )))))))))))))))))))))))))))))))))))))))))))) 39 Appendix D 40 Auto-Size Label: Section 5.3.3. Clears the use of auto-size values set by ^A1^D39. Uses the values obtained instead of those in the format file. Automatically sizes the label and send the results out the serial port. Same as ^A2^D39, but prints the values on a label, instead of on the screen. Clear Commands 41-51. XX 41 Load number of fields in layout (HFM): Preceded by ^A.
Appendix D )))))))))))))))))))))))))))))))))))))))))))) XX Quick Reference Command Summary 61 Mark Text Starting Position: ^A designates which text field to start entering new data. Section 5.3.8. 62 Pre-padded Text: This command is sent after text that is to appear at the beginning of each field is sent. 63 Text Mode Control: Section 5.3.8. Disable 1 & 2. Enable auto-print mode Clear all previous text upon receiving new data. Enable 1 & 2.
Quick Reference Command Summary )))))))))))))))))))))))))))))))))))))))))))) Appendix D 77 User Display: This command temporarily displays a user defined message in the printers first and/or second line of the LCD. This command must be enabled by dip switch #3 position 2. A carriage return must follow the ^D77 command. The message string must follow this command ,be surrounded by quotes and also terminate with a carriage return.
Appendix D )))))))))))))))))))))))))))))))))))))))))))) Quick Reference Command Summary XX 87 Load Increment/Decrement Value Into Memory: Will load and store a step value into non-volatile user memory. The stored serial number to be affected is chosen with the XX variable and the actual step value, up to 9 characters, is entered by following the ^AXX^D875 with the step value surrounded by quotes. XX 88 Send Serial Number To Serial Port: ^A specifies which stored serial number (1-16) to send.
Quick Reference Command Summary )))))))))))))))))))))))))))))))))))))))))))) Appendix D XX 109 Delete Single Volatile Graphic Image: ^A selects which slot (1-16) to erase. XX 110 Delete Single Non-Volatile Downloadable Font: ^A select the font to erase (18). XX 111 Load Non-Volatile Downloadable Font: ^A selects which slot (1-8) to place the font in. ^A0 selects the next available slot. XX 112 Load Volatile Downloadable Font: ^A select which slot to place the font in (116).
Appendix D )))))))))))))))))))))))))))))))))))))))))))) Quick Reference Command Summary XX 130 Load Database: Up to 2048 ASCII characters can be stored in the database. Storage is terminated by an ESC character or the 2048 limit. XX 131 Read Database: The full string of 2048 characters is sent to the serial port. XX 132 Clear Database: XX 139 Adjust Size of Automatic Reverse Video Text Fields (AN=4): This command increases the size of all AUTOMATIC REVERSE VIDEO TEXT FIELDS.
Quick Reference Command Summary )))))))))))))))))))))))))))))))))))))))))))) Appendix D X 153 Round/Expand Floating Point Fraction: This command will round or expand the Floating Point Fraction to the desired number of decimal places. If the decimal places specified by 'X' is equal to the current decimal place, no operation is performed. If larger than the current decimal place, trailing 0's are added to the fraction.
Appendix D )))))))))))))))))))))))))))))))))))))))))))) Quick Reference Command Summary APPENDIX E: HARDWARE DIP SWITCHES (inside printer) Hard Switch 1 12345678 xxxxxxxx *******. 0=Serial, 1=Parallel ******.) 0=RS-232C, 1=422 or 485 *****.)) 0=No Parity, 1=Enable Parity ****.))) 0=Odd Parity, 1=Even Parity ***.)))) 0=8 Data Bits, 1=7 Data Bits **.)))))))), *.)))))))),* .
Index ^A 41, 44-52, 54-57, 60-62, 64-66, 70, 79, 80, 83, 84, 86, 87, 102, 106-111 ^B 41, 45, 64, 102 ^C 15, 16, 41, 49, 102 ^D 41, 43-52, 54-57, 60, 61, 64-66, 70, 79, 80, 83, 84, 86, 87, 102 ^E 15, 16, 41, 42, 64, 102 ^H 42 ^K 42, 49, 102 ^L 42, 49, 102 ^M 42 ^Q 42 ^S 42 Accumulator 41 Bar code 1, 15, 18, 24-27, 29, 40, 61, 62, 64, 71-75, 101 Bar code Symbologies 1, 27 Batch Mode 1, 4 Baud Rate 4, 113 Cable Pinout 13 Centronics ii Character Count 25, 29, 30, 32, 40, 86 Character Generators 17 Character Mul
Index )))))))))))))))))))))))))))))))))))))))))))) Label Control Byte 22, 56, 106 Label Fields 24 Label Header 16, 18-20, 23, 50, 51, 56, 99 Label Jams 3 Label Samples 91 Label Size X Direction 20 Label Size Y Direction 20 Line Feed 45, 65, 103 Offset 22, 57, 81, 82, 97, 98, 106 Parallel 4, 13, 14, 16, 113 Physical 5 Power-Up 11, 43, 45, 47, 48, 50, 57, 62, 64-66, 91, 103, 105, 106, 108 Print Head 1, 11, 12, 18, 49, 61, 63, 74, 90, 105 Print Width 3 Printing Commands 49 Repair 90 Reset 45, 64, 65, 105 Reso
Notes ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________
