User's Manual

Frequently Asked Questions (FAQ)
Question
Solution
Power LED won’t light up
No sound
3.5 mm stereo plug connected,
but no sound
Static sound heard when volume
knob is turned
What are the products
supported?
Sound is distorted
If the problem still exists, please contact the distributor or ask for professional service
Check if the system is powered on
Check the power plug is well connected
Check if the audio source is working well
Check if the audio and speaker cables are connected
Check if the volume is at the right level
Turn off the speaker power for about 3 seconds, then turn on
again to change the connection mode.
Turn off the playback source first, then turn the speaker volume
knob several times. Playback again and monitor. The static noise
is due to dust, so simply turning the volume will remove it easily.
Any plackback devices such as PC, notebook, CD/DVD player,
Media players with 3.5 mm stereo plug, or Bluetooth enabled.
Check if the source file is not corrupted, play a different song and
test
Out power power, RMS 24 Watt RMS
Power distribution, Watt 7 Watt x 2 + 10 Watt
Harmonic distortion < 0.3% 1 W 1 kHz
Frequency response 60 Hz - 20 kHz
Signal/Noise ratio, dB > 75 dB
Separation, dB > 45 dB
Tweeter driver type 2.5”
Tweeter impedance 8 Ohm
Woofer driver type 4”
Woofer impedance 4 Ohm
Input 3.5 mm stereo jack, Bluetooth® 4.0
Output 2RCA
AC IN 120V~ 60Hz 220mA
Amplifier
Speaker
Interface
Connections and Operations
EN
5
EN
6
Operation:
1. Plug the AC power plug to the wall AC source or any AC power distribution sockets.
2. Ensure the volume level is lowered to minimum.
3. Turn on the power switch located at the rear of the subwoofer. The blue LED on the side will illuminate
indicating power on status.
4. If the 3.5 mm stereo jack is connected for external analog source, the blue LED will remain dim. The sound
input is now through this analog connection.
5. If the 3.5 mm stereo jack remain unconnected for 3 seconds, the system will commence the Bluetooth
pairing mode.
6. Turn on the Bluetooth mode on your smartphone or tablet or notebook. Pair and connect to the speaker
system.
7. Start the media player and its playback audio. The Blue LED will slow blink between dim and bright
intensity.
8. Slowly increase the volume to your preferred listening level. You can adjust the volume from either the
media player, or the speaker’s side volume knob.
9. To change modes, please turn off the power for 3 seconds and then restart again.
10. If you connect the 3.5 mm stereo jack during Bluetooth mode, the system will not revert to analog mode. It
will remain in the Bluetooth streaming mode. To change to the 3.5 mm stereo (analog) mode, please turn
off the speaker system for 3 seconds and turn back on again.
Installation:
Precaution: Prior to connecting the speakers, ensure the AC power plug is removed from the AC source.
Secondly, ensure the volume knob is set to zero.
1. Connect the both satellite speaker’s cable (3.5mm) to the audio output at the rear panel of the subwoofer.
2. Place both satellites on extreme sides of the listening position.
3. Place the subwoofer on the floor and with its back near the wall for more bass.
4. For analog connection, connect the playback source (smartphone, tablet, Mp3/Mp4 player, DVD/Blu-ray/CD
player) to the 3.5mm audio input jack.
5. Last, connect the AC power cord to the AC power supply source. Please always ensure the AC power ratings
printed on the rear panel of the satellite match with your country's AC power supply ratings. If they do not
match, please do not connect or turn ON the power. This will damage the speaker system.
6. For Bluetooth mode: 3 seconds after powering up, the system will go to Bluetooth pairing mode . Turn on
your Bluetooth enabled device and connect to the speaker system.
7. On your Bluetooth device, under Settings - Bluetooth screen, click on search and discover the speaker
system.
8. Select the speaker system and connect to it.
Technical Information
- the end -
turn on Bluetooth
& select “M-113 BT”
pair and connect
“M-113 BT”
M-113 BT
M-113 BT
iPhone, iPad, or iPod
go to SETTINGS > GENERAL > enable BLUETOOTH > select “M-113 BT”
Android Phone
go to SETTINGS > WIRELESS & NETWORKS > enable BLUETOOTH > select “M-113 BT”
Others
read the instruction manual included with your device