User’s Manual EtherFast 10/100M Smart Switch Model No.: SP616DB / SP624DB http://www.micronet.
Package Contents Verify your package contains the following items: z SP616DB/SP624DB 10/100 Mbps Smart Switch z User’s Manual z Power Cord z Rack Ears with Screws and Rubber Foots Features Micronet SP616DB/SP624DB has the following key features: z Provide 16 (SP616DB) or 24 (SP624DB) RJ-45 ports of 10/100 Mbps, auto negotiation z Provide one expansion slot for optional fiber optic module z Provide one web-based console port z Provide 2K (SP616DB)/10K (SP624DB) MAC address and 2M (SP616DB)/1.
POWER This LED comes on when the switch is properly connected to power and turned on. TX/FX Push Button The push button is located at the right side of port 16 (SP616DB) or port 24 (SP624DB). Release this button to use RJ-45 port 16 (SP616DB) or port 24 (SP624DB), and press this button to use the 100BASE-FX module. IP RESET Push Button Press the front panel IP RESET push button for around five seconds to reset the Switch back to default IP Address (192.168.1.10).
Installation Preparing the Site Select the site that meets the following requirements: Characteristic Requirement Temperature 32 to 104˚F (0 to 40˚C) Humidity Maximum relative humidity of 90%, non-condensing Condition At least 1.8 meters (6 feet) to the nearest source of electromagnetic noise Ventilation Minimum 3 inches (0.25 feet) of clearance around the ventilation openings Power Outlet Within 1.
Step 2: Remove the module from the static-free container. Step 3: Unscrew the cover plate of the expansion slot. (The slot for single-port module is located at the right side of the switch.) Step 4: Remove the plate. (Keep it for future use in case you decide to remove this module later.) Step 5: Carefully slide the module into the slot, along the internal plastic guide rails. Step 6: Once it is fully slid in, snap in the module to make a proper connection. Step 7: Fasten the module screws then.
Switch Configuration Setting UP Console Port Connection SP616DB/SP624DB provides one RJ-45 console port and a web-based interface, allowing users to configure and manage the switch remotely from web browser. 1. Connect UTP/STP cable to SP616DB/SP624DB’s console port. Figure 5: Connect directly to PC 2. Figure 6: Connect to PC via another switch In the web browser, specify the default IP address of SP616DB/SP624DB (192.168.1.10).
Figure 8: Main menu System Change The System Change parameters can be displayed by clicking the System Change button in the left sub-menu. Figure 9: System Change z z z Switch Name: Type a switch name and replace the current switch name with a new one. (Please restart your Computer once the Switch Name is replaced and saved under “Save Configuration “by the new name ). Note: only “a-z “, “A-Z”, “0-9”, “under line” & “Space” can be acceptable, totally can not exceed 16 characters.
IP Configuration Figure 10: IP Configuration z z z Refresh: Click the Refresh button and refresh back to the last saved IP Configurations. IP Address, Netmask, Default Gateway: You can see and change the IP Address, Netmask, and Default Gateway of the Ethernet Switch. Apply: Click the Apply button and apply the new IP Configurations. Port Figure 11: Port z z z z z Refresh: Click the Refresh On or Refresh Off button to or not to refresh back to the last saved settings of the ports.
VLAN Figure 12: VLAN z z VLAN: Click and choose the ports to be added into the VLAN groups. Apply: Click the Apply button and apply the new settings of the VLAN groups. Note: all Ports have to be selected to one of the VLAN Groups, those Port/Ports were not selected will be notified by the alarm message which shows “Non-Identify VLAN Group “.
Trunk SP616DB: Figure 13: Trunk of SP616DB z z z z Disable: Click and choose the Disable to disable the Trunk Group 1 or Trunk Group 2. Trunk Group 1: Click and choose the Port 1, 2 to be added into the Trunk Group 1. Trunk Group 2: Click and choose the Port 9, 10 to be added into the Trunk Group 2. Apply: Click the Apply button and apply the new settings of the Trunk Groups. SP624D: Figure 14: Trunk of SP624DB z z z Trunk Group 1: Click and choose any four ports to be added into the Trunk Group 1.
Save Configuration Figure 15: Save Configuration z z Click Save Configuration. Click the Ok or Cancel button to or not to save the configurations. Note: the Cancel button will discard any data you have changed since the last "Save" operation. Without clicking Ok button, the switch does not save any changes you may have made. Load Default Figure 16: Load Default z z Click Load Default. Click the Ok or Cancel button to or not to load the default settings.
Specifications IEEE standard IEEE 802.3,10BaseT IEEE 802.3u,100BaseTX/FX Port SP616DB: 16 10/100 Mbps ports SP624DB: 24 10/100 Mbps ports Speed 200 Mbps full-duplex 100 Mbps half-duplex Dimension 440 × 207 × 44 mm rack-mount size Weight SP616DB: 1.94 kg SP624DB: 2.07 kg Power Input 100 - 240 VAC, 50 - 60 Hz Input Fuse SP616DB: 3.3VDC, 2.5A SP624DB: 3.3VDC, 5A; 5V, 1A Power Consumption SP616DB: 8.25W Max. SP624DB: 21.5W Max.
