User's Guide

Connect the Device
Wireless connection
The client-side connects to router Wi-Fi
The defaulted username
and password are on the
bottom label
Wired connection
Or
Connect the PC and router via LAN1, LAN2 or LAN3 with cable
cable
switch on
cable
cable
cable
Or
Use DSL or PON for Internet connection
modem
Community broadband Internet access
telephone line or fiber
2.1. Configure the Router in Bridge Mode
2.2. Configure the Router in Gateway Mode
2.3. Configure the Router in Repeater Mode
User Guide
AC1200 Gigabit Dual Band Wi-Fi Router
② Enter the router management interface and select the network-
mode. Change the mode to gateway mode.
③ In the router management interface, click Install-Install Settings
and select PPPoE. Fill in the User Name and Password, click Save.
Wait for the device to save the settings and Internet access is
available. The Wi-Fi name is the default name (on the label at the
bottom of the device).
2.2.2. Static IP for Internet Access
In the router management interface, click Network-Network
Settings-WAN Connection, select Static IP in WAN Access Type, fill
in the IP Address, Subnet Mask, Default Gateway and DNS1 (DNS2
and DNS3 are optional) and click Save&Apply, wait for the device to
save the settings and Internet access is available. The Wi-Fi name
is the default name (on the label at the bottom of the device).
2.2.3. Dynamic IP for Internet Access
The router is defaulted to dynamic IP (DHCP Client) for Internet
access. The Wi-Fi name is the default name (on the label at the
bottom of the device).
After the connection is completed, use a mobile phone or computer
to search for the Wi-Fi name 2.4G SSID or 5G SSID on the label at
the bottom of the device, enter the password, connect to the Wi-Fi,
and then the Internet access is available.
① In the router management interface, select Network-Mode,
change the mode to Repeater, and click Save&Apply.
② In the new router management interface, select Network—5G
Settings—Network Scan, click Site Survey, select the uplink signal,
click Next.
2.2.1. Dial-up for Internet Access：
①After the connection is completed, use a mobile phone or
computer to search for the Wi-Fi name 2.4G SSID or 5G SSID on
the label at the bottom of the device and enter the corresponding
password to connect to Wi-Fi. Open the mobile phone or computer
browser, visit the 192.168.10.1 website, enter the default username
and default password on the label at the bottom of the device, and
enter the router management interface.
4.5. Check the device information in topology
4.3. Step 3: Two devices’ EasyMesh networking
After the two devices complete step 1 and step 2, the General
interface will refresh, and the Start PBC button will appear.
In the General interface of one of the devices, click the Start PBC
button or short press the device's WPS button, and within two
minutes enter the General interface of the other device, click Start
PBC button or short press the WPS button of the device to trigger
automatic network pairing. (Note that long pressing the WPS key is
rest)
In the router management interface of the Controller, select
Network-EasyMesh-Topology,you can see the device name and IP
address.
Perform step 2 on the third and more devices.
Manufacturer: Micronet Union Technology(Chengdu)
Co., Ltd
Address: Room 502, Building 5, N.O. 528, Yuefei Road,
Shibantan Street, Xindu District, Chengdu, Sichuan, China
After finishing step 2, perform step 3 for EasyMesh networking with
routers that have been networked.
4.4. EasyMesh networking of three or more devices
FCC Radiation Exposure Statement: The antennas used for
this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be
co-located for operating in conjunction with any other
antenna or transmitter.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures: ‐‐Reorient or relocate the
receiving antenna.
‐‐Increase the separation between the equipment and
receiver.
‐‐Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
‐‐Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
FCC Warning Statement
In the router management interface, select Network-EasyMesh-
General, select Disabled in Role, and click Save. Then the
EasyMesh network can be disabled.
4.1. Step 1: set up the Controller
In the router management interface connected to the upper-level
gateway (optical modem),select Network—EasyMesh—General, in
the general settings page:
① Fill in Mesh Controller in Device Name.
② Select Controller in Role.
③ Click Save & Apply.
4.2. Step 2: set up the Agent
The Agent needs to be in the Bridge mode in 2.1.
In the router management interface of other routers (except the
router set in the first step), select Network—EasyMesh—General, in
the general setting page:
① Fill in Mesh Agent in Device Name.
② Select Agent in Role.
③ Click Save & Apply.
① Implementation of the three guarantees regulations, seven
days return, 15 days replacement, one-year warranty;
② The free warranty period of the product is one year,
calculated from the date of sale;
③ Under the following circumstances, three guarantees are
not implemented, and paid maintenance is implemented:
a. Failure caused by man-made damage, improper operation
or irresistible natural disasters;
b. Failure caused by remodeling, disassembling and
assembling the product by yourself;
c. Exceeding the validity period.
After-sales Service Commitment
Packing list:
1.The device
2.User guide
3.Power adapter
4.Ethernet cable
If the above accessories are missing, please contact the
customer service for replacement.
1. Schematic Diagram of Router Connection
2. Configure the Internet
In the router management interface of 192.168.10.1, click Install-
Install Settings, you can customize the 2.4G and 5G SSID and
Password.
3. Revise Wi-Fi Password
Precautions:
① After completing EasyMesh networking, the Controller device will
synchronize its 2.4GHz and 5GHz SSID, password, and channel
with the Agent device. That is, these configurations of the Agent
device will be the same as the Controller device.
② After modifying the SSID, password, and channel on the
Controller device, the Controller device will synchronize these
configurations to all Agent devices. Modifying the SSID and
password on the Agent device will not be synchronized.
③ After the device restarts after a power failure, the device will
restore the EasyMesh network group by default, and no connection
settings are required.
④ If the EasyMesh function of the Controller device is disabled, the
entire EasyMesh network will be disabled.
⑤ If the EasyMesh function of the Agent device is disabled, the
device will leave the EasyMesh network.
⑥ If you need to switch the access mode of a certain Mesh device,
you need to turn off the Mesh function of the device first, and then
turn on the Mesh function to complete the switching of the access
mode.
⑦ The Agent device is not supported to connect to other Mesh
devices via Wi-Fi and wired at the same time. That is, the Agent
device can only use one of Wi-Fi and wired to connect to other Mesh
devices.
When router’s EasyMesh has been disabled, the device will depart
from the original EasyMesh network. If to open EasyMesh again,
please perform step 2 and step 3 to rejoin the network.
6. Other information
5. Disable EasyMesh
4. Configure EasyMesh
③ Fill in Pre-Shared Key and click Connect.
quick guide(说明书)
Technical requirements:(技术要求)
1. Material:80g double-sided coated paper(材质：80g双铜 双面黑白印刷)
2. Size:90*150mm(单页尺寸：90*150mm)