Analogue Display
mn100 Analogue Display EMC Conformance All Tacktick equipment is designed to the best industry standards for use in the recreational marine environment. The design and manufacture of Tacktick equipment conforms to the appropriate Electromagnetic Compatibility (EMC) standards. Correct installation is required to ensure that performance is not compromised. Important Due to the wireless communication systems used in Micronet instruments they are only recommended for use on boats up to 18 meters (60 ft.
Contents 1 2 Information Page 1.1Introduction 1.2Specifications 1.3Power Management and Battery Life 1.4Safety and Disposal - 2 2 2 4 Operation 2.1Display Information 2.2Switching the System On and Off 2.3Backlighting 2.4Audible Signals and Alarms 2.5Utilities 2.6Chapter and Page Operation 2.7Chapter and Page Description - 3 Setup and Calibration 3.1Entering Setup and Calibration Mode 3.2Chapter and Page Setup and Calibration 3.3Editing Values 3.
mn100 Analogue Display 1 Information 1.1 Introduction Your Micronet display is powered for life by the environment. Although feature packed and highly visible in all conditions, current demand is so low, and the supply so efficient, that the solar-powered display is self sufficient. Combined with other displays in the Micronet range this display becomes part of a complete navigational system. 1.2 Specifications Height of digits: 7mm (0.
Introduction Bright Sunny Day Battery is charged and being topped up by the sun. (see Note) Battery is low and being charged by the sun. Overcast Day Battery is charged and requires no further charging. Battery is low but maintaining it’s level. Night Battery is charged but is not charging. Battery is low with no charging. LOW Power It is recommended that the instrument be left in daylight for some time for the battery to recover, or charge from an external 9-30V power source.
mn100 Analogue Display Sleep Mode If there is no boat speed or change in heading registered on the system for a period of 12 hours your Micronet display will switch off to conserve power. A "POWER SAVE" alarm will sound before the system switches off. Pressing any button within 10 seconds of the alarm sounding will allow the system to remain switched on. Backlighting will automatically shut down/off when operated in daylight. Artificial light WILL NOT recharge the battery.
Operation 2 Operation Important: Ensure that the "Auto Network" procedure described on the yellow instruction sheet and full Setup and Calibration has been performed correctly before attempting to use your Micronet system. 2.
mn100 Analogue Display 2.2 Switching the System On and Off To switch your Micronet system on or off select any display and press the button for 2 seconds. Switch On 2.3 Switch Off Backlighting At any stage of the display’s operation press and hold for 2 seconds the button to access the lighting control. Pressing the and buttons will scroll through the options: OFF, 1, 2 and 3 whilst changing the backlighting.
Operation 2.5 Keylock Utilities The Keylock feature protects from accidental key presses and is intended for use in high activity applications such as crewed race yachts. If your display is mounted in a position where keys may be pressed accidentally (eg the companionway of a race yacht), then you can enable keylock as follows: Press and hold to enter set up Press repeatedly to reach the OPTS chapter Press repeatedly to reach the Key Lock page Press to activate keylock. Press and hold to exit setup.
mn100 Analogue Display 2.6 Chapter and Page Operation Information is displayed in a "Chapter and Page" format using the button to scroll through the chapters and the and buttons to move between pages. The diagram below shows the information format. Default Chapter Selection 8 www.tacktick.
Operation Pressing the button at any time will move on to the next chapter and on scrolling through the chapters the page last selected in that chapter will be displayed. Both chapter and page selection will scroll back to the first page once a cycle has been completed.
mn100 Analogue Display 2.7 Chapter and Page Descriptions 360 Degree Wind Chapter 1 30 60 Apparent Wind Angle and Speed The apparent wind angle and speed with respect to the vessel as measured by the Wind Transmitter. The wind angle is shown on a 360 degree scale. 30 60 90 90 120 120 150 2 30 60 150 True Wind Angle and Speed The true wind angle with respect to the vessel and the true wind speed calculated by the display taking into account the vessels speed through the water.
Operation 6 Turn The pointer shows the direction of the target waypoint relative to the bow of the boat. The display shows the distance to the waypoint. The distance is displayed in the currently selected system distance units (default Nautical Miles). Warning: the Turn page uses GPS COG and BTW and therefore takes tide and set into account. With the pointer dead ahead, your course is directly to the waypoint, but you may not be pointing at the waypoint.
mn100 Analogue Display 10 Tack 30 30 60 60 90 90 120 50 15 11 The compass heading that the vessel will follow should it tack through the wind, calculated by the display. Apparent wind angle and magnetic heading must be available for this calculation to be made. 50 COG 30 30 60 60 90 90 The vessel’s course over the ground as calculated by the GPS Antenna. The pointer points to the direction of North.
Set-up and Calibration 3 Setup and Calibration 3.1 Entering Setup and Calibration Mode To enter the Setup and Calibration Menu press and hold for 2 seconds the button. 3.2 Chapter and Page Setup and Calibration Setup and calibration functions are displayed in a "Chapter and Page" format using the button to scroll through the chapters and the and buttons to move between pages. The diagram below shows the information format.
mn100 Analogue Display 3.4 Setup Page Description UNIT - Units Chapter Press the button quickly to edit, press the or to change units and press the button quickly to select the chosen units. Default values are indicated in bold. s1 Wind Speed Sets the units in which all Wind Speed related information is displayed. KTS (Knots) or M/S (meters per second). WIND - Wind Chapter Press the button quickly to edit, press the or to change units and press the button quickly to select the chosen units.
Set-up and Calibration OPTS - Options Chapter Press the button quickly to toggle the values between settings or press the button quickly to edit, press the or to change values and press the button quickly to select the chosen value. Default values are shown in bold. s5 Auto Networking Only available on the display which was used to power up the system. Refer to the "Auto Network" sheet for further information. s6 Key Lock Enables or disables the keylock function. See page 7, section 2.5.
mn100 Analogue Display s10 Boat Show Allows the display of information when NOT installed as part of a Micronet system for demonstration purposes only. Off / On. s11 LCD Contrast Adjusts the viewing angle and contrast of the LCD display to improve visibility under varied mounting possibilities. Optional values 1 - 7, default 4. s12 Pointer Type Toggles the width of the pointer.
Title s16 Wind Transmitter Signal Strength As above but for Wind Transmitter information. s17 Wireless (NMEA) Interface Signal Strength As above but for Wireless (NMEA) Interface information. s18 Mast Angle Sensor Signal Strength As above but for Mast Angle Sensor information. S19 MOB Sensor Signal Strength As above but for MOB sensor information. S20 - Type 6 to Type 9 reserved for future use. www.tacktick.
mn100 Analogue Display 4 Seatrial and Calibration Once the Micronet system has been Autonetworked and installation on the vessel has been completed it is necessary to carry out calibration. It is not safe to use the displays for navigational purposes until calibration has been carried out correctly. 4.1 Wind Calibration Both wind speed and direction can be calibrated to ensure that readings from the Wind Transmitter are displayed accurately. Wind Angle Offset Motor the vessel directly into the wind.
Installation 5 Installation 5.1 Tools list and Parts Tools Required 2.5mm or 5mm Drill Bit (7mm if power connection required) Power Drill Cross Head Screwdriver Parts List 5.2 Mounting Template Display Backplate and 2x Clip Brackets Mounting Screws (3) Mounting Bolts (3) M4 Studs & Thumbnuts (3) Sealing Gaskets (4) Double Sided Tape Precautions and Positioning Advice Ensure mounting surface is flat. Leave space between displays for sun covers. Leave space to remove display from bracket (if used).
mn100 Analogue Display 5.3 Bracket Mounting (Preferred Method) This method allows for the easy removal of a display as and when required, for either security reasons or to prevent damage or discomfort whilst not in use. 1. Using the three supplied M4 bolts attach the back plate to the rear of the display (Fig.1). 2. Drill three 2.5mm holes marked "A" on the Template and using the supplied self tapping screws, screw the clip bracket to the mounting surface (Fig.2). 3.
Installation 5.4 Surface Mounting Where there is no access to the rear of the mounting surface Easy installation but will allow removal without gaining access to the boat. Position the supplied Template carefully before starting. 1. Drill three 2.5mm holes marked "B" on the template. 2. Carefully snap the facia of the display off the main body taking care not to drop the button pads.
mn100 Analogue Display Where access is available to the rear of the mounting surface This method allows for maximum security of a permanently mounted display. Position the supplied template carefully before starting. 1. Drill three 5mm holes marked "B" on the template. 2. Screw the four M4 brass studs into the rear of the display. 3. Place the display in position pushing the three studs through the newly drilled holes. 4.
Maintenance and Fault Finding 6 Maintenance and Fault Finding 6.1 Care and Maintenance All Micronet products are totally sealed against water and are not serviceable. Any attempt to take a Micronet product apart will invalidate the warranty. To clean, use only a damp, soft cloth. No detergents, solvents or abrasives should be used. To avoid damaging a Micronet display unit we recommend storing in the supplied soft pack when not in use.
mn100 Analogue Display No NMEA data showing on external displays. From any display enter setup and calibration mode (page 13) and scroll through to the Health chapter. Check the signal level and battery status of the Wireless (NMEA) Interface box. Lost Network Alarm Sounds Indicates that the display has lost communication with the master. Either there is a problem with the master* or the display has been moved out of effective range.
Maintenance and Fault Finding 7 Warranty Information General All Tacktick products are designed and built to standards suitable for use in a harsh marine environment. If the products are installed correctly and operated as described in the user guides they will provide long and reliable service. For information and assistance Tacktick operates a network of international distributors.
mn100 Analogue Display Alternatively, if the product is being used away from the country of purchase, it may be returned to the national distributor, or one of its approved dealers, in the country where it is being used. In this case valid claims will cover parts only. labor, handling costs and return shipping will be invoiced to the sender. Disclaimer Tacktick products should only be considered an aid to navigation and common sense must be applied at all time when navigating at sea.
