Nokia Bluetooth Headset BH-608 1 2 5 6 7 3 4 8 9 10
11 12
ENGLISH DECLARATION OF CONFORMITY Hereby, NOKIA CORPORATION declares that this BH-608 product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/phones/ declaration_of_conformity/. © 2010 Nokia. All rights reserved. Nokia, Nokia Connecting People and the Nokia Original Accessories logo are trademarks or registered trademarks of Nokia Corporation.
ENGLISH Introduction With the Nokia Bluetooth Headset BH-608, you can make and answer calls hands-free with your compatible mobile device. The headset is provided with digital signal processing (DSP) noise cancellation that helps you handle calls in noisy environments. Read this user guide carefully before using the headset. Also, read the user guide for the device that you connect to the headset. This product may contain small parts. Keep them out of the reach of small children.
ENGLISH Get started The headset contains the following parts shown on the title page: earpiece (1), microphone (2), mute key (3), answer/end key (4), charger connector (5), volume up key (6), volume down key (7), clip (8), indicator light (9), and power key (10). Before using the headset, you must charge the battery and pair the headset with a compatible device. Warning: Use only chargers approved by Nokia for use with this particular model.
ENGLISH If the ambient temperature falls below 0°C (32°F) or exceeds 55°C (131°F), charging stops temporarily until the temperature rises to 0°C (32°F) or falls below 55°C (131°F). 3. When the battery is fully charged, the green indicator light is displayed. Disconnect the charger from the headset, then from the wall outlet. The fully charged battery has power for up to 8 hours of talk time or up to 200 hours of standby time.
ENGLISH Pair and connect the headset Before using the headset, you must pair and connect it to a compatible device. You can pair the headset with up to eight devices, but you can only connect it to a maximum of two devices at a time. 1. Ensure that your mobile device is switched on and the headset is off. 2. If the headset has not been previously paired with a device, switch on the headset. The headset enters pairing mode, and the blue indicator light starts to flash quickly.
ENGLISH You may be able to set your device so that the headset connects to it automatically. To activate this feature in a Nokia device, change the paired device settings in the Bluetooth menu. Basic use Change the earpad The headset may be provided with different sized earpads. Select the earpad that fits the best and is the most comfortable for your ear. To change the earpad, pull the current earpad from the earpiece, and push the new earpad into place.
ENGLISH feature with the headset), when no call is in progress, press the answer/ end key twice. To activate voice dialling (if your mobile device supports this feature with the headset), when no call is in progress, press and hold the answer/ end key for about 2 seconds. Proceed as described in the user guide of the mobile device. To answer or end a call, press the answer/end key. To reject a call, press this key twice. To mute the microphone during a call, slide the mute key towards the microphone.
ENGLISH Activate or deactivate vibration Allow connection to two devices You can set the headset to vibrate and flash the indicator light when you receive a call. By default, the vibration and the indicator light are activated. To deactivate the vibration and the light, press and hold the answer/end key and the volume down key for about 5 seconds when the headset is connected to a device. To activate the vibration and the light, press and hold the answer/end key and the volume up key for about 5 seconds.
ENGLISH To answer a call on the second connected device and end the active call on the first device, press the answer/end key. To answer a call on the second connected device and put the active call on hold on the first device, press and hold the answer/end key for about 2 seconds. To end the active call on the second connected device and make the call on hold active on the first device, press the answer/end key.
ENGLISH Battery and charger information This device has an internal, nonremovable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device. This device is intended for use when supplied with power from the following chargers: AC-3, AC-4, AC-5, DC-4, and DC-9. The exact charger model number may vary depending on the type of plug. The plug variant is identified by one of the following: E, EB, X, AR, U, A, C, K, B, or UB.
ENGLISH Never use any charger that is damaged. Operating times are estimates only. Actual performance depends on many factors such as device settings selected, device features being used (or running in the background), battery condition and ambient temperature. Taking care of your device Your device is a product of superior design and craftsmanship and should be treated with care. The following suggestions will help you protect your warranty coverage. • Keep the device dry.
ENGLISH • Do not paint the device. Paint can clog the moving parts and prevent proper operation. These suggestions apply equally to your device, charger, or any accessory. Recycle Always return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you help prevent uncontrolled waste disposal and promote the recycling of materials. Check product environmental information and how to recycle your Nokia products at www.nokia.com/werecycle, or nokia.
ENGLISH if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.
