8860 User Guide Draft pre-release version 0.
Indicators and Icons You have an active call. The phone is waiting for you to enter a response. The current profile you have selected for your phone is 6LOHQW. Keyguard has been activated to help prevent any accidental keypresses. You have one or more voice messages waiting. You have one or more unread text messages waiting. Digital service is available. Any characters you enter will be upper-case letters or numbers. Press the # key to switch letter case.
Safety At A Glance 1. Safety At A Glance Read these simple guidelines before using your phone. Failure to comply with these guidelines may be dangerous or illegal. For more detailed safety information, “Important Safety Information” on page 91. Interference All mobile phones may get interference which could affect performance. Use Sensibly Use only in the normal position (to ear). Avoid unnecessary contact with the antenna when phone is on.
Getting Connected Using this Guide 2. Getting Connected The wireless phone described in this guide is approved for use in TDMA/AMPS networks. A number of features included in this guide are called Network Services. They are special services provided by wireless service providers. Before you can take advantage of any of these Network Services, you must subscribe to the service(s) from your home service provider and obtain instructions for their use.
Getting Connected Press and hold the button at the top of the battery. Slide the battery toward the bottom of the phone. Lift the battery off the phone. Charging your new battery Your phone can be used with either a rechargeable Li-Ion or NiMH battery. Note that a new battery’s full performance is achieved only after two or three complete charge and discharge cycles. When is a good time to charge? You can charge your battery anytime.
Getting Connected Important Battery Information • Note that a new battery’s full performance is achieved only after two or three complete charge and discharge cycles! • The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk time and standby time) is noticeably shorter than normal, it is time to buy a new battery. limited in temperatures below 14º F (-10º C).
The Basics 3. The Basics Get a good signal Your phone operates on radio waves, and the quality of radio reception depends entirely on the strength of the radio signal in your area. You have purchased a powerful phone, with lots of features. Read this section for some very basic information on how to use your phone. This radio coverage is maintained by a wireless network and the quality of calls on a wireless phone depends on the strength of the wireless radio signal.
The Basics Editing a number on display Press to move the cursor to the left and to move it to the right. Press &OHDU to delete the character to the left of the cursor. s t Dialing stored phone numbers View stored names and numbers by pressing page 16), then press B t or s from the start screen (see See “Phone book” on page 57 for details on storing numbers. Want to stop your phone from ringing without answering the call ? Press P quickly when the phone rings.
Using Your Phone Deactivating Keyguard • Press 8QORFN then 4. Using Your Phone • Press and hold E until 8QORFN NH\V" appears and press 2. Note: When Keyguard is 21, calls to the emergency number programmed into your phone (e.g. by pressing 911 then B) may be possible. However, Emergency key 9 doesn’t work. Answering a call with Keyguard active During an incoming call the keypad automatically unlocks.
Using Your Phone Scroll bar Scrolling through the main menu When you access your phone’s menu and submenus, you will notice a scroll bar at the far right of the screen. This bar indicates your location in the menu structure; each “tab” on the bar represents a different menu item. Press 0HQX at the start screen. Then press item. For example, press 0HQX once. The scroll bar appears with the first (top) tab displayed.
Using Your Phone 1 1 2 Saved 3 1 2 8 Lights (only in &DU profile) 1 1 3 Write new * 3 1 2 9 Automatic answer (only in &DU and +HDGVHW) 1 1 4 Outbox * 3 1 3Rename (not available in 1RUPDO profile) 1 1 5 Erase all 3 2Silent * Only where available. Please see “Text messages and pages” on page 71 for details.
Features A to Z 4 2 5 7Chinese Traditional 4 2 6Slide setting 5. Features A to Z 4 3Security settings 4 3 1Restrict calls 4 3 2Access codes ABC mode 4 4Network services This allows you to enter names into your phone book. 4 4 1Voice privacy See “Entering letters and numbers” on page 42.
Features A to Z Select either DP or SP and press 2. Note: Step 4 appears only if you have selected am/pm format; see “Selecting time format” on page 37 for more information. Note: This can only be used when your phone is connected to a headset or to an approved handsfree car kit equipped with the ignition sense option, with the ignition on. When the alarm goes off Activating automatic answer Press 6WRS to shut off the alarm. Press 0HQX 3 (3URILOHV) Snoozing Your phone lists each profile.
Features A to Z Calculator Calculating exchange rates Your phone’s calculator adds, subtracts, multiplies, divides, and converts currency. Enter number of units, then press 2SWLRQV Remember! Your phone must be switched on to use this feature. Do not switch on the phone when wireless phone use is prohibited or when it may cause interference or danger.
Features A to Z Tip: Use to move the cursor right and to move it left. When you enter a digit, it writes over the number to the right of the cursor. t s Option 4: View all This allows you to view the notes of the entire calendar. Use or to scroll through the notes. &DOHQGDU PHPRU\ HPSW\ will appear if there are no notes in the calendar. t Your phone displays the current day. You can also scroll to different days by pressing or . t s Once you’re at the date you want, press 2SWLRQV.
Features A to Z Press Use t t to reach &DOOHU JURXSV. Press 6HOHFW to reach the group you want. Press 6HOHFW Press until you see *URXS ULQJLQJ WRQH. Press 6HOHFW. Use to reach the tone you want to hear when anyone from this group calls you. Press 2.. t t Tip: You can set your phone to ring only when people from certain caller groups call you, and to otherwise be silent. When Caller ID is active, your phone may display the caller’s phone number.
Features A to Z Press or to &DUG QDPH and press 6HOHFW. Enter card name using your phone’s keypad, press 2.. t s See “Entering letters and numbers” on page 42 if you need help on entering the card name For details about your phone’s security code, see “Security code” on page 68. Dialing Sequence Access no. + phone no. + card no. Access no. + card no. + phone no. Prefix + phone no. + card no.
Features A to Z Your phone will attempt to call the network to confirm the feature code you entered in Menu 4 4 5 (see “Network feature setting” on page 53) Once the feature code had been confirmed, the feature is activated Call forwarding options )RUZDUG DOO FDOOV forwards all incoming calls. )RUZDUG LI EXV\ forwards calls only when you’re on the phone. )RUZDUG LI QRW DQVZHUHG forwards calls if you don’t answer. )RUZDUG LI RXW RI UHDFK forwards calls if you are out of the serving wireless network.
Features A to Z Call timers Ending the calls Your phone automatically keeps track of the amount of time you’ve spent in calls. Activating call waiting Press 0HQX 2 5 (&DOO ORJ - &DOO WLPHUV) Scroll repeatedly to access the following options /DVW FDOO displays call duration of last call. $OO FDOOV displays call duration of all calls made since timers have last been reset (see page 36 for details on how to clear call timers). /LIH WLPHU shows duration of all calls; this can not be reset (see page 48).
Features A to Z Clear call lists This feature will clear all dialed numbers, as well as numbers of answered calls and missed calls. You can not undo this operation, so be careful. Note: The clock is powered by your phone’s battery. If your clock has been activated and you remove the battery while your phone is still on, you will need to reset the time after you turn your phone back on. Also, see “Call log” on page 32.
Features A to Z Note: This feature may not be available in all wireless systems. See your service provider for details and availability. Customer care contact number Making a conference call With the press of a single button, you can quickly attempt calls to your service provider. This feature can be helpful if you’re having difficulties dialing a number, especially when traveling outside your home area.
Features A to Z Earpiece volume The scroll keys on your phone will adjust the earpiece volume during a phone call. The top scroll key increases while the bottom one decreases the volume. If an accessory like a headset or a car kit, or one with its own loudspeaker, is connected to your phone, the scroll keys will adjust the volume for that accessory. Note: Using the scroll keys to adjust earpiece volume functions only during phone calls.
Features A to Z Entering letters and numbers Changing letter case You can enter letters, as well as numbers, when storing information into your phone by using your phone’s keypad. When you see the letter you wish to enter, simply press the key associated with that letter until it appears on the display (numbers also appear). ABC mode When you need to enter letters into your phone, it will automatically switch over to mode. Your phone displays the icon to indicate that your phone is in ABC mode.
Features A to Z (Z) creates a “wait” when a number is dialed. The “Z” makes your phone wait for you to press 6HQG or B, then it sends the digits located to the right of the “w” as touch tones (see page 76). You can add as many special characters as you need in a single number sequence. These characters can not be entered while in mode. Snake Feed the snake with as many goodies as possible and watch it grow. Use keys 2, 4, 6, and 8 to turn the snake toward food.
Features A to Z Inbox Keypad tones When you receive a text message, it’s stored in the Inbox. Your phone will display 0HVVDJH UHFHLYHG, along with the text message icon, and makes a sound (depending on the message alert tone; see page 51). This is one of the settings in your phone’s Profiles (see page 61). It sets the volume of the tone you hear when you press your phone’s keys. Please see “Text messages and pages” on page 71 for complete details on this feature.
Features A to Z See “Call timers” on page 34. Last number redial Your phone lists each profile. Use t to highlight &DU and press 2SWLRQV. Note: &DU will not appear in the list until the phone has been connected to a car kit at least once time. Highlight &XVWRPL]H and press 2.. Press t to highlight /LJKWV and press 6HOHFW. to scroll through your choices and press 2.
Features A to Z Note: When you change your lock code, make sure you store it in a safe place, away from your phone. Avoid entering access codes similar to emergency numbers to prevent accidental emergency calls. Messages Manual touch tones Using messages This setting determines how long touch tones are produced as you press the keys on the keypad. Note that touch tones are sometimes called DTMF tones. Scroll to one of the following options, then press 6HOHFW See “Touch tones” on page 76 for details.
Features A to Z Microphone When the )RUZDUG LI QRW DQVZHUHG option in the Call Forwarding feature (see page 31) is selected, your phone treats the forwarded calls as missed calls. You can mute and unmute your phone’s microphone while a call is in progress. During a call, your phone’s softkeys change from 1DPHV and 0HQX to 2SWLRQV and 0XWH. Also, see “Call log” on page 32 for details on other call lists.
Features A to Z When you subscribe to any of these services, your service provider or dealer gives you a separate feature code to activate each service. Deactivation codes are used to deactivate each service. Once you store the appropriate code in your phone, the service appears as a menu item. You can then use the menu to activate and deactivate these services. Each time you use a feature that requires a feature code, that code is sent to the network to verify you’re using the correct feature code.
Features A to Z Note: If you press and hold 1, your phone calls your voice mailbox. If you press and hold 9, and Emergency key 9 (Menu 4 1) is 21, your phone attempts a call to the emergency number programmed into your phone (e.g. 911 or other official emergency number). Phone book Changing numbers in one-touch dial list Things to know about the phone book With this feature, you can assign a different number to any one-touch dial location. Stored numbers may be up to 32 digits long.
Features A to Z Storing a name and number Press 'HWDLOV Press 1DPHV Press 2SWLRQV Scroll to $GG QHZ and press 6HOHFW Highlight (UDVH, then press 6HOHFW, then 2. Enter name using the keypad (use # to switch between upper and lower case) and press 2. Note: You can not undo Erase functions, so be careful! Erasing your entire phone book Enter phone number and press 2. Also, see “Entering letters and numbers” on page 42 and “Quick save” on page 70.
Features A to Z Answering a call with phone lock on Press any key except E and P Turning off phone lock Press 0HQX 4 3 2 1 (6HWWLQJV - 6HFXULW\ VHWWLQJV - $FFHVV FRGHV - 3KRQH ORFN). Enter lock code and press 2.. Then scroll to 2II and press 2. again. With phone lock off, you can now use your phone without entering the lock code each time you turn your phone on. Phone settings Phone settings allow you access to other phone features such as an alarm clock and your phone’s language.
Features A to Z When you select &XVWRPL]H, press 2. and you’ll have access to several lists and sub-menus that will enable you to adjust the settings on the current Profile. Note: &DU and +HDGVHW will not appear in the Profiles list unless your phone is connected to a car kit or a headset. However, they will remain in the menu once connected for the first time. Restoring factory settings Press 0HQX 4 2 4 (6HWWLQJV - 3KRQH VHWWLQJV - 5HVWRUH IDFWRU\ VHWWLQJV), enter security code and press 2..
Features A to Z Adding call restrictions Press 0HQX 4 3 1 (6HWWLQJV - 6HFXULW\ VHWWLQJV - 5HVWULFW FDOOV) Scroll to 5HVWULFW RXWJRLQJ FDOOV and press 6HOHFW Enter the security code and press 2. Scroll to $GG UHVWULFWLRQ to create an outgoing call restriction and press 2. Enter the number string you wish to restrict and press 2..
Features A to Z Ringing volume Roaming Indicators This is one of the settings in your phone’s Profiles (see page 61). It sets the default ringing volume for incoming voice calls and message alert tones. When your phone begins roaming, it will beep once and display 52$0 or (;7(1'(' $5($, depending on how roaming works with your phone. Contact your service provider for more details. If your phone is not roaming (i.e. in its home area) it will either display +20( or the name of the service provider.
Features A to Z Security settings This menu includes the following security features: Enter new security code again at 9HULI\ QHZ VHFXULW\ FRGH , press 2. Phone will display 6HFXULW\ FRGH FKDQJHG 4-3-2 $FFHVV FRGHV - See page 21. Note: If you have changed your security code and don’t remember the new code, contact your service provider. Once you have changed your security code, the default setting is no longer valid.
Features A to Z 4-1 &DOO VHWWLQJV - See page 33. 4-2 3KRQH VHWWLQJV - See page 60. 4-3 6HFXULW\ VHWWLQJV - See page 68. 4-4 1HWZRUN VHUYLFHV - See page 54. This feature is 0HQX 5 in your phone. The default is $XWRPDWLF, which means your phone automatically searches for networks available to you and chooses the appropriate one. Every time you switch on your phone, it resets this to $XWRPDWLF. If you choose 0DQXDO, your phone searches for networks, then begins displaying them.
Features A to Z Also, the maximum length of a text message may depend on the network’s capabilities. Text message options When you access 7H[W PHVVDJHV, you will view a screen with five different options. is where incoming messages are received and stored. All new, unread messages are kept here. ,QER[ 6DYHG is where all saved, read messages are kept here. :ULWH QHZ 2XWER[ allows you to write text messages, text pages, and e-mail messages. is where outgoing messages are stored.
Features A to Z When you receive a text message Text messages are shown in the order that they were received, in their order of priority. 0HVVDJH UHFHLYHG indicates an unread message or page. If more than one message is received, the number of received messages will be listed first. 1HZ HPHUJHQF\ PHVVDJH indicates that the message or page received was sent by someone via the service provider. Emergency messages are sent only in situations where life and/or property are in immediate danger.
Features A to Z Touch tones Note: See “Special Characters (for storing numbers)” on page 43 for details on “p” and “w” characters. Your phone can generate various sounds, called touch tones, when the keys are pressed. These are also known as DTMF tones. When you dial this number, your phone first dials the phone number, then waits (because of the “w” character) for you to press 6HQG. Your phone then sends your password.
Features A to Z You can set the touch tone length by pressing 0HQX 4 2 3 2 (6HWWLQJV - 3KRQH VHWWLQJV - 7RXFK WRQHV - 7RXFK WRQH OHQJWK). Unlocked phone number When the phone lock is on (see page 59), no calls can be made. However, you can store one number into your phone that can be called when it’s locked. Storing the unlocked phone number Press 0HQX 4 3 2 2 (6HWWLQJV - 6HFXULW\ VHWWLQJV - $FFHVV FRGHV - 8QORFNHG SKRQH QXPEHU) Enter lock code and press 2.
Features A to Z When you’re ready to store your voice mailbox number, press 0HQX 1 2 2 (0HVVDJHV 9RLFH PHVVDJHV 9RLFH PDLOER[ QXPEHU). Then enter your voice mailbox phone number and press 2.. This number can be up to 32 digits long and is used until it’s changed. So if your phone number changes, you may need to change your voice mailbox number along with it. Volume You can adjust the ringing volume and earpiece volume with your phone. See “Earpiece volume” on page 40 and “Ringing volume” on page 66.
Accessories The welcome note displays each time your phone is switched on. Characters you enter are added to the left of the cursor. Press &OHDU to delete characters to the left of the cursor. Press or to move the cursor right or left. t 6. Accessories s See “Entering letters and numbers” on page 42 for details. Write new This feature allows you to write text messages, text pages, and e-mail messages with your phone.
Accessories Batteries Standby and Talk Times The following table shows battery options that are available for your phone, charging times with the Rapid Travel Charger (ACP-9U) and the Standard Travel Charger (ACP-7U), talk times, and standby times. Consult your service provider for more information. These charging times are approximate. Battery Option CONTAINS: Nickel metal hydride or lithium ion battery.
Accessories Note: When a charger is not in use, disconnect it from the power source. Do not leave the battery connected to a charger for longer than a week, since overcharging may shorten its life. If left unused, a fully charged battery will discharge itself over time. Calls are possible during charging. A green light indicates the charger is ready for charging (when not charging) or finished charging (if it has been charging).
Troubleshooting 7. Troubleshooting DCH-9 Rear Slot Charging Times BLS-2 Extended Li-Ion 900 mAh 6 hrs 30 min 8 hrs 30 min 4 hrs 10 min 5 hrs 25 min What if charging fails? BMS-2/BMS-2S Extended NiMH 900 mAh If 1RW FKDUJLQJ is displayed, charging is suspended. Make sure the battery is connected to an approved charging device and that the battery is at room temperature. Extreme temperatures, hot or cold, can affect your battery’s performance and prevent charging.
Reference Information Note: Check with your service provider for information about when you need to dial a ‘1’ and/or an area code in addition to the number. If you make a mistake dialing Press &OHDU to delete the last character entered, or press and hold &OHDU to delete all characters entered. 8. Reference Information Important Safety Information Traffic Safety Do not use a hand-held telephone while driving a vehicle. If using a hand-held phone park the vehicle before conversing.
Reference Information Electronic Devices Vehicles Most modern electronic equipment is shielded from radio frequency (RF) signals. However, certain electronic equipment may not be shielded against the RF signals from your wireless phone. RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (e.g. electronic fuel injection systems, electronic anti-skid (anti-lock) braking systems, electronic speed control systems, air bag systems).
Reference Information Check regularly that all wireless phone equipment in your vehicle is mounted and operating properly. Key in the emergency number for your present location (e.g. 911 or other official emergency number). Emergency numbers vary by location. Do not store or carry flammable liquids, gases or explosive materials in the same compartment as the phone, its parts or accessories. Press B For vehicles equipped with an air bag, remember that an air bag inflates with great force.
Technical Data Care and Maintenance Your phone is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and allow you to enjoy this product for many years. When using your phone, battery, charger, OR any accessory: • Keep it and all its parts and accessories out of small children’s reach. • Keep it dry. Precipitation, humidity and liquids contain minerals that will corrode electronic circuits.
Technical Data CANADA NOKIA PRODUCTS LTD. – 575 Westney Rd. South, Ajax, Ontario L1S 4N7. Tel: (905) 427-6654 5. Upon request from NMPI, the Consumer must provide information to reasonably prove the date of purchase. The information contained in this phone was written for dual-mode TDMA and AMPS phones. The right to make changes and improvements to any of the products described in this guide without prior notice is reserved. Issue No. 1 Phase 2 ©1998 Printed in Canada 09/98 Nokia Mobile Phones.
Technical Data d) The Consumer will be billed for any parts or labor charges not covered by this limited warranty. The Consumer shall be responsible for expenses related to reinstallation of the Product.
102
