Specifications

ManualsBrandsMicrotek ManualsComputer equipmentScanMaker i460

Step 2: Install Software

Step 1: Unpack Contents

Start Here

Installing your Microtek ScanMaker i460

Unpack your scanner package and check for

major components.

1. ScanMaker i460 scanner

2. Power adapter

3. Software CDs/DVDs

4. Hi-Speed USB cable

5. LightLid 35 IV*

Important: Do not remove the yellow stickers from your

scanner until you are told to do so. You must install software

before connecting your scanner.

Always close any open programs and turn off Anti-virus

utilities before installing software.

I49-004750 B, September 2013

* The LightLid 35 IV is either as a standard equipment or an

optional accessory depending on the scanner configuration that

you purchased.

PC:

A. Place the Microtek Software CD/DVD

into a drive, and follow the on-screen

instructions to install the scanner

driver and software.

B. Restart your computer at the end of

all software installation.

NOTE: If the Microtek Software Installer screen does

not come up automatically, double-click the

following in succession: “My Computer”; the CD/

DVD-ROM icon; then cdsetup.exe to start the

installer program.

MAC:

A. Place the Microtek Software CD/DVD

(ScanPotter) into a drive, and double-click

the ScanPotter installer icon to install

ScanPotter.

B. Install the remaining software

components, then restart your computer

at the end of all software installation.

NOTE: After rebooting your Macintosh, the Microtek

software will attempt to locate your scanner on the

system. Since this is your first install and you have not

yet connected the scanner, simply ignore the message

that appears and proceed to the next step.

Summary of content (10 pages)

PAGE 1
Start Here Installing your Microtek ScanMaker i460 Step 1: Unpack Contents Unpack your scanner package and check for major components. 1. 2. 3. 4. 5. ScanMaker i460 scanner Power adapter Software CDs/DVDs Hi-Speed USB cable LightLid 35 IV* 2 1 3 * The LightLid 35 IV is either as a standard equipment or an optional accessory depending on the scanner configuration that you purchased.
PAGE 2
Step 3: Unlock Scanner A. Remove the yellow “Step 3” sticker from your scanner. B. With the scanner power off, tilt the back left corner of the scanner to see the locking switch at the bottom. C. Push the locking switch to the position as indicated in the graphic, with the icon on the lock showing as “Unlocked”.
PAGE 3
Step 4: Connect Scanner (cont.) To the Hi-Speed USB cable D. Connect one end of the cable to your computer. E. Connect the other end of the cable to the scanner. D E IV F. Press and hold the Power button ( ) on the button panel for a while. Once the scanner is detected by your system, the LED (green) will brighten, and the scanner is ready to scan.
PAGE 4
Using the LightLid 35 IV NOTE: If your scanner configuration does not contain the LightLid 35 IV and you do not have intention to use this device, please ignore this section. Connecting the LightLid 35 IV 1. Remove the scanner lid. 2. Ensure that the scanner is powered off; then plug the connector of the LightLid into the scanner’s 9-pin accessory port. To load film B. To load slides: A. To load filmstrips: Turn the LightLid 35 IV over.
PAGE 5
Basic Scanning for PC Users Scanning Photos 1. Place the photo. IV To scan a photo, place the photo on the scanner bed. The top end of the original should be positioned towards the right of the scanner, with the surface to be scanned facing down. WEB PDF OCR E-MA IL COPY SCAN POWE R 2. Launch ScanWizard EZ. To launch ScanWizard EZ as a stand-alone program, double-click the ScanWizard EZ icon on your desktop.
PAGE 6
Scanning Film 1. Place the film. To scan film, use the LightLid 35 IV. Refer to “Using the LightLid 35 IV” in this guide to load film. 2. Launch ScanWizard EZ. Follow the step 2 in “Scanning Photos” on previous page to launch ScanWizard EZ. 3. Switch to ScanWizard EZ - Professional Mode. Click the Professional Mode button on the control panel of the EZ Mode to switch to the Professional Mode. 4.
PAGE 7
Basic Scanning for Mac Users 1. Place the scan material. • To scan photos, place the photo to be scanned on the scan bed, as detailed in the “Basic Scanning for PC Users” section in this guide. • To scan film, use the LightLid 35 IV, as detailed in the “Using the LightLid 35 IV” section in this guide. 2. Launch ScanPotter as a stand-alone by clicking on the program icon, or by selecting it from the application folder in your Mac OS X system. 3.
PAGE 8
Scan frame (enclosed by dotted lines) Click the Scan Settings button to switch back to the default control panel of ScanPotter Click the Image Settings button to switch to a window where contains a composite display of nineimage-effects (Filter column) and additional image correction tools (Additional Adjustment column) for your scanned image.
PAGE 9
Problems? The LEDs on the button panel indicate the status of the scanner. IV On - Scanner is on Both on - Ready to scan WEB PD F OC R E-M AIL CO PY Flashing - Scanning or error happened SC AN POWE R LED (orange) LED (green) Off - Scanner is off If you encounter any problems, check the section below and follow the suggested solution if your problem is listed.
PAGE 10
Do You Need Assistance? Manuals If you have additional questions and need further instruction or information, we provide electronic manuals for: 1. Using your ScanMaker i460 (Supplementary information) 2. Using the ScanWizard EZ or ScanPotter scanning software 3. Using the bundled third-party software To access the electronic manuals: Insert the scanner’s software CD/DVD into your computer’s CD/DVD-ROM drive.