Technical Manual

10
Function Name Description
P
ush
B
u
t
t
ons
R
F
O
N
/O
F
F
S
wi
t
c
h
e
s
t
he
t
r
an
sm
i
tt
e
r
R
F
ou
t
pu
t
be
t
w
ee
n
s
t
an
d
b
y
(
S
T
B
Y
)
an
d
transmit (XMIT) conditions. In STBY, the RF output is zero.
BR
I
GH
T
NE
S
S
S
e
t
s
t
he
d
i
s
p
l
a
y
b
r
i
ghtn
e
ss
t
o
h
i
g
h
(
H
)
,
l
ow
(
L
)
, or a
u
t
om
at
ic
(A; light sensing).
LED
D
i
sp
l
a
y
s
S
T
B
Y
I
n
di
ca
t
es
t
he
HD
X
-
1
1
00
i
s
i
n
s
t
andby
m
o
d
e
(No RF output; unit is powered but not transmitting).
X
M
I
T
I
n
di
ca
t
es
t
he
HD
X
-
1
1
00
i
s
i
n
tr
a
n
s
m
i
t
m
o
d
e.
D
C
OK
I
n
di
ca
t
es
D
C
P
o
w
er
i
s
app
l
i
ed
t
o
t
he
R
emo
t
e
C
o
n
t
r
ol
P
a
n
el
a
n
d
transmitting.
F
A
U
L
T
I
n
di
ca
t
es
an
e
r
r
o
r
co
n
d
i
t
i
on
i
n
t
he
HD
X
-
1
1
0
0
tr
a
n
s
m
i
tt
e
r
.
HI
I
n
di
ca
t
es
t
he
HD
X
-
1
1
00
i
s
i
n
h
i
g
h
R
F
ou
t
put
m
o
d
e.
LO
I
n
d
i
c
a
t
es
t
h
e
HD
X
-
1100
i
s
i
n
l
o
w
R
F
o
u
t
p
u
t
m
o
d
e.
E
N
C
RYP
T
IO
N
I
n
d
i
c
a
t
es
t
h
e
HD
X
-
1100
i
s
tr
a
n
s
m
it
t
i
n
g
an
e
n
c
r
y
p
t
ed
s
i
g
n
al
V
ID
E
O
I
n
d
i
c
a
t
es
t
h
e
presence
o
f
a
v
i
d
e
o
s
i
g
n
a
l
at
t
he
H
D
X
i
n
p
u
t
R
o
t
a
r
y
Switches
R
F
H
I/
L
O
W
S
e
t
s
t
he
HD
X
-
110
0
t
o
h
i
gh
(
H
I
) or
l
ow
(
L
O
)
R
F
p
o
w
er
o
u
t
pu
t
mode.
P
R
E
SE
T
S
e
l
ect
fr
om
1
t
o
9
prese
t
s.
C
H
A
N
N
EL
Select from 1 to 15 channels
L
C
D
D
i
sp
l
a
y
P
R
E
SE
T
D
i
sp
l
a
ys
t
he
cu
r
r
ent p
r
e
s
et
n
u
m
b
e
r
.
C
H
A
NNE
L
D
i
sp
l
a
ys
t
he
cu
r
r
ent ch
a
n
n
e
l
n
u
m
b
e
r
.
Use a 9-pin RS-232 null-modem cable to connect the communication path between the RCU
and the HDX-1100.
A receptacle at the rear of the controller supplies DC power to the RCU. Vislink provides the
2-pin Weidmuller connector (Part # 52104-2) to connect to the power receptacle at the rear or
the controller. The required power range is from +18 to +32Vdc (negative ground only).
NOTE: During initial power up, the RCU will display a C until the HDX-1100 processor
completes a boot up and self check sequence; this is normal. If the C does not disappear
within one to two minutes, the HDX-1100 has lost power or a communications error has
occurred; check the circuit breakers, and power and serial cable connections.
To facilitate updating or servicing an HDX-1100 transmitter, we recommend that the
transmitter and RCU panel are fed from different circuit breakers. In normal operation, power
should be applied to the RCU first, or to both units simultaneously.