User's Manual

www.vislink.com
© 2011 Vislink Group. All rights reserved. All other products or services referenced herein are
identied by the trademarks or service marks of their respective companies or organizations.
Note: Vislink reserves the right to change specications without notice. Please contact your
representative to conrm current specications. Document 10 / 7 / 2011
Specications
Electrical
At 20±5°C ambient
Parameter Conditions Min Typ Max Units Comment
Frequency Range L3211-2027 2000 – 2700 MHz
L3211-6475 6400 - 7500 MHz Does not include LDPD
RF Output Power ALC Mode +28 (0.63) 28.75(0.75) +30 (1.0) dBm (W)
RF Input Power Range ALC Mode +10 (10) – +24 (250) dBm (mW)
Gain Fixed Gain Mode 10 – 15 dB
Spectral Regrowth Adjacent Channel – – -40 dBc EN 302 064-1 §7.3.4
Alternate Channe – – -46
Spurious 25MHz – 1GHz – – 0.25(-36) nW(dBm) EN 302 064-1 §7.4.6
1GHz – 27GHz – – 1(-30)
Return Loss – 10 – dB
RF Input
Damage Level
CW +27 (0.5) dBm (W)
Pulsed +36 (4)
Static Protection Direct Discharge 8 kV IEC61000-4-2
Air Discharge 15
Temperature Rise Above Ambient 32 ºC IEC60417-5041
Supply Voltage 9 28 V
Power Consumption RF OFF 7.5 W
RF ON 14 W
Compliance
Standard Class/Category Version
ETSI EN 302 064-1 Category 1 V1.1.2
ETSI EN 301 489-28 Class B V1.1.1
Environmental
Operating Temperature
(Portable Equipment)
• -10°C to +50°C
Storage Temperature
• -20°C to +80°C
Humidity
• 95%
• Non-Condensing
IP Rating
• 54
Mechanical
RF/DC Input Connector
• 50Ω N Type (M)
RF Output Connector
• 50Ω N Type (F)
Power Connector
• 6-Pin Lemo Socket
Phantom Power
• Applied to RF Input Connector
Weight
• 0.32Kg
Length
• 106mm (inc. connectors)
Diameter
• 62mm
Status Indicator
• Green (DC Power/ALC OK)
• Orange (DC Power OK/Fixed Gain)
Power Connector 6-Pin Lemo Socket
L3211 Socket
• EEG.OB.306 CLV
Mating Plug
• FGG.0B.306 CLA (straight)
• FHG.0B.306 CLA (right-angle)
Pin Out
• 1 & 2: GND, 3 & 4: +VE, 5 & 6: NC
Note: When operating the barrel booster
in the ‘Fixed Gain’ mode the RF output
power is no longer controlled by the
barrel booster’s ALC and therefore it is the
operator’s responsibility to ensure that
the RF drive into the barrel booster is at an
appropriate level not to cause over-drive
or damage and to maintain regulatory
compliance.
Hot surface, do not touch barrel booster
heat sink surface during operation.
The barrel booster is supplied with 2 complimentary
power cables from the options listed below
PN:9003434 Barrel Booster ALC Power Cable (Lemo straight)
Pn:9003435 Barrel Booster ALC Power Cable (IDX D-TAP)
Pn:9003437 Barrel Booster ALC Power Cable (Anton Bauer P-TAP)
Pn:9003438 Barrel Booster ALC Power Cable (Lemo right-angle)