User Manual
Table Of Contents
- Notices
- Contents
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the Display Screens
- 3.5 PTX-PRO Monitoring Operations
- 3.6 PTX-PRO Control Operations
- 3.7 Front Panel vs. Configurator Settings
- Troubleshooting
- Advanced Operation
- 5.1 Chapter Overview
- 5.2 Before You Begin
- 5.3 Create or Update a Configuration
- 5.3.1 Using the Configurator Software
- 5.3.2 Determine Licensed Options
- 5.3.3 Create New Configuration On-Line
- 5.3.4 Load and Modify Configuration Settings On- Line
- Figure 5-7: Load and Modify Configuration Settings On-Line - Sheet 1 of 5
- Figure 5-8: Load and Modify Configuration Settings On-Line - Sheet 2 of 5
- Figure 5-9: Load and Modify Configuration Settings On-Line - Sheet 3 of 5
- Figure 5-10: Load and Modify Configuration Settings On-Line - Sheet 4 of 5
- Figure 5-11: Load and Modify Configuration Settings On-Line - Sheet 5 of 5
- 5.3.5 Load Configuration File into Radio On-Line
- 5.3.6 Change Preset Names in On-Line Mode
- 5.3.7 Create Channel Plan Offline
- 5.3.8 Modify Channel Plan in Offline Mode
- 5.3.9 Load and Modify a Channel Plan On-Line
- 5.3.10 Load Channel Plan File into Radio On-Line
- 5.3.11 Add Licensed Option
- Installation
- 6.1 Chapter Overview
- 6.2 Unpacking
- 6.3 Initial Inspection
- 6.4 Damage in Shipment
- 6.5 Mounting and Cabling
- 6.6 Power Connections
- 6.7 Grounding
- 6.8 Audio Connections
- 6.9 Signal Connections
- 6.10 Data Connections
- 6.11 Powering Up
- 6.12 Configurator Software Installation
- 6.13 Product Modifications
- Replacement Parts
- Theory of Operation
- Index
Routine Operation 3-7PTX-PRO User and Technical Manual
3.5.1 Using the Monitor Screens in COFDM Mode
When the PTX-PRO is operating in the COFDM mode, 70 MHz
COFDM IF output from the internal COFDM/MPEG board is
supplied to the RF output and MONITOR connectors. See
Figure 3-5 on page 3-8 for the COFDM Monitor Menu Map.
3.5.2 Using the Monitor Screens in ASI/SDI Input
Mode
When the PTX-PRO is operating in the ASI In mode, the internal
MPEG encoder is bypassed and an externally supplied ASI
stream is routed to the MONITOR and RF output connectors.
See Figure 3-6 on page 3-9 for the ASI In Menu Map.
3.5.3 Using the Monitor Screens in Ext IF Input
Mode
When the PTX-PRO is operating in the Ext. IF In mode, the 70
MHz IF input signal to the SIGNAL INPUT connector is routed
through the transmitter. See Figure 3-7 on page 3-10 for the Ext.
IF Monitor Map.
3.5.4 Using the Monitor Screens in LMS-T Mode
When the PTX-PRO is operating in the LMS-T mode, this mode
Topic Page
Using the Monitor Screens in COFDM Mode 3-7
Using the Monitor Screens in ASI/SDI Input Mode 3-7
Using the Monitor Screens in Ext IF Input Mode 3-7
Using the Monitor Screens in LMS-T Mode 3-7
utilizes a single carrier modulator and supplies a configurable
LMV-S signal to the transmitter RF output and MONITOR
connectors.
This mode is operational for QPSK and 16 QAM modulation
formats. See Figure 3-8 on page 3-11 for the LMS-T Monitor
Menu Map.