User Manual
Table Of Contents
- Notices
- Contents
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the Display Screens
- 3.5 PTX-PRO Monitoring Operations
- 3.6 PTX-PRO Control Operations
- 3.7 Front Panel vs. Configurator Settings
- Troubleshooting
- Advanced Operation
- 5.1 Chapter Overview
- 5.2 Before You Begin
- 5.3 Create or Update a Configuration
- 5.3.1 Using the Configurator Software
- 5.3.2 Determine Licensed Options
- 5.3.3 Create New Configuration On-Line
- 5.3.4 Load and Modify Configuration Settings On- Line
- Figure 5-7: Load and Modify Configuration Settings On-Line - Sheet 1 of 5
- Figure 5-8: Load and Modify Configuration Settings On-Line - Sheet 2 of 5
- Figure 5-9: Load and Modify Configuration Settings On-Line - Sheet 3 of 5
- Figure 5-10: Load and Modify Configuration Settings On-Line - Sheet 4 of 5
- Figure 5-11: Load and Modify Configuration Settings On-Line - Sheet 5 of 5
- 5.3.5 Load Configuration File into Radio On-Line
- 5.3.6 Change Preset Names in On-Line Mode
- 5.3.7 Create Channel Plan Offline
- 5.3.8 Modify Channel Plan in Offline Mode
- 5.3.9 Load and Modify a Channel Plan On-Line
- 5.3.10 Load Channel Plan File into Radio On-Line
- 5.3.11 Add Licensed Option
- Installation
- 6.1 Chapter Overview
- 6.2 Unpacking
- 6.3 Initial Inspection
- 6.4 Damage in Shipment
- 6.5 Mounting and Cabling
- 6.6 Power Connections
- 6.7 Grounding
- 6.8 Audio Connections
- 6.9 Signal Connections
- 6.10 Data Connections
- 6.11 Powering Up
- 6.12 Configurator Software Installation
- 6.13 Product Modifications
- Replacement Parts
- Theory of Operation
- Index
Installation 6-9PTX-PRO User and Technical Manual
6.8.2 Rear Panel Audio Connections
The rear panel AUDIO 3 & 4 10-pin female connector receives
balanced audio inputs for audio channels 3 and 4. This
connector is used for both Audio B inputs.
The mating connector that plugs into this panel connector is
described below.
Manufacturer: Amphenol (or ITT Cannon)
Part Number MS3116F12-10S (KPT06F12-10S)
Description: 10-Pin, Female, Plug
Rear panel AUDIO 3 & 4 connector pin-outs are shown in Table
6-3.
Table 6-3: Rear Panel Audio Connector Pin-Outs
Connector
Information
Pin-Out Signal Description
10-Pin, Male, Panel-
Mount
A DIGITAL 1 CH1 +
B DIGITAL 1/2 GND
C DIGITAL 1 CH1 -
D DIGITAL 2 CH2 +
E DIGITAL 2 CH2 -
F ANALOG 3 RIGHT
CH2 -
G ANALOG 3/4 COM
H ANALOG 3 RIGHT
CH2 +
J ANALOG 4 LEFT CH2 -
K ANALOG 4 LEFT
CH2 +
H
A
B
J
C
D
E
F
G
K
The PTX-PRO provides a maximum of four audio circuits. Each
audio circuit is a 3-wire balanced circuit capable of carrying one
tone or voice signal. An audio circuit can carry one analog
balanced channel or two digital AES/EBU channels.
6.8.3 MPEG Audio Input
MPEG audio circuits must be configured in pairs:
• Audio A - Channels 1 and 2
• Audio B - Channels 3 and 4
Audio channels are configured using the Configurator software.