Owner's manual

RECHANNELIZE

TRANSPOSE

ToprogramtheFootswitchControllertorechannelizeanincomingMIDIchanneltoaselectedoutgoingMIDIchannel

whenthefootswitchisdepressed,senditthefollowingSystemExclusiveProgrammingcommand:

( , ,and areoptional)

AllbytesmustbeinHexadecimalformat(seehexadecimalconversiontableatend)

isoptional,ifincludedthenthe16notesfrommiddleCupareusedtoselectthechannel.Ifomitted,then

thenumberofnotesplayedwhilethefootswitchisdepressedisusedtoselectthechannel.

=IncomingMIDIchanneltorechannelize(seeMIDIchanneltableatend)

isoptional,specifiespresetoutgoingMIDIchannel(seeMIDIchanneltableatend)

isoptional,ifincludedthenincomingnotesareignoredwhilefootswitchisdepressed

TorechannelizeanincomingMIDIchanneldepressthefootswitch(theAll-Notes-Offmessageissentoutatthistime),

selectthechannelbyplayingnotesonthekeyboard(thesenotesarenotechoedtoMIDIOut),andreleasethe

footswitch.IfnonotesarereceivedbytheFootswitchControllerduringthisperiod,theoutgoingMIDIchannelisset

tothepreset .ToprogramtheFootswitchControllertoignoreincomingnotesandchangedirectlytothepreset

MIDIchannel whenthefootswitchisdepressed,insert intheabovecommandasshown.

ToprogramtheFootswitchControllertoacceptrechannelizeselectionforincomingMIDIchannel1whenthe

footswitchisdepressed,senditthefollowingSystemExclusiveprogrammingcommand:

F00000500409 F7

TorechannelizefromMIDIchannel1toMIDIchannel2depressthefootswitch,playanytwonotes,andreleasethe

footswitch.AllMIDIchannel1messageswillnowberechannelizedtoMIDIchannel2.Continuingtotapthe

footswitchwillcausetheFootswitchControllertotogglebetweentheoriginalandselectedchannels.

ToprogramtheFootswitchControllertotransposeincomingnotemessagesbyaselectedintervalbydepressingthe

footswitch,senditthefollowingSystemExclusiveProgrammingcommand:

( and areoptional)

AllbytesmustbeinHexadecimalformat(seehexadecimalconversiontableatend)

=IncomingMIDIchanneltotranspose(seeMIDIchanneltableatend)

isoptional,specifiespresettransposeinterval(40=zerotranspose)

isoptional,ifincludedthenincomingnotesareignoredwhilefootswitchisdepressed

Tospecifyatransposeintervaldepressthefootswitch(theAll-Notes-Offmessageissentoutatthistime),playthe

noteaboveorbelowmiddleCcorrespondingtothetransposeinterval(thisnoteisnotechoedtoMIDIOut),and

releasethefootswitch.IfnonotesarereceivedbytheFootswitchControllerduringthisperiod,thetransposeinterval

issettothepresettransposeinterval .ToprogramtheFootswitchControllertoignoreincomingnotesandchange

directlytothepresettransposeinterval whenthefootswitchisdepressed,inserta afterthe intheabove

programmingcommand.

F00000500409(10)cc(pp)(00)F7 10pp 00

pp 00

ExampleSetting

ExampleOperationwithAboveSetting

F0000050040Acc(pp)(00)F7 pp 00

pp 00 pp