WALKIE-TALKIE DUAL BAND PMR446/LPD › User’s manual up to 8Km* * Depending on terrain XT50 PRO
Main functions • Dual Band LPD/PMR446 transceiver 85 channels: 69 LPD + 16 PMR446 • Waterproof IPX2 • Power: 500mW ERP (PMR446); 10 mW ERP (LPD) • Side Tone: end transmission noise muffler • LCD display with backlight • Low battery indicator • Auto power save: automatic current economy circuit • 38 CTCSS and 83 DCS tones in TX and RX • CALL button • RRM channel (only for Italy) • Battery life up to 12 hours • SCAN function • Monitor function • Keypad lock • Roger Beep on/off • VOX for hands-free communicati
Content of the package • • • • 2 transceivers with belt clip 2 rechargeable battery packs 700mAh 2-way USB cable 2 earphone mikes MA21Li (only in the Hobby&Work version) Coverage The maximum range depends on terrain condition and is obtained during use in an open space. The only limitation to maximum possible range are environmental factors such as blockage caused by trees, buildings, or other obstructions. Inside a car or a metallic constructions, the range can be reduced.
Identifying the parts Display 3 10 2 5 6 PTT SPK MIC PTT SPK 7 4 8 MIC 1 9 XT50 PRO XT50 PRO Selected channel VOX - Function activated - Keypad lock activated H/L - Indicates the high / low power selection in transmission (only in PMR band) 5. - Battery status indicator 6. RX - Radio in rx mode (busy channel) 7. TX - Radio in transmission (PTT pressed) 8. DCS/CTCSS - Type of sub-audio tone selected 9. Code of the selected CTCSS or DCS tone (CTCSS: 1-38; DCS: 1-83) 10.
Transceiver 1 2 SPK 3 MIC 4 8 5 6 5 7 PTT SPK PTT SPK XT50 PRO 9 MIC MIC 12 10 11 XT50 PRO 4| XT50 PRO user’s manual
Antenna LCD display MENU/ - Press this control to turn on/off the unit or to enter the radio’s menu 4. CALL/ – Press this button to lock the keypad or to send out a call signal. 5. ▲-▼ controls - use these buttons to adjust the volume, select the channels and functions. 6. Microphone 7. Built-in Speaker. 8. MON/SCAN - With this button you can enable/disable the Scan and Monitor functions. 9. SPK | MIC (under the protective cover) - To connect to external audio devices such as microphones, headphones, etc.
Let’s communicate! To turn on/off the radio Hold down MENU/ for 3 seconds. Channel selection Press once the Menu button and then select the desired channel by the ▲/▼ buttons. Press PTT to confirm the selection. Remember that both radios must be set on the same channel. Transmission Keep pressed the PTT button. The display will show “Tx” and “to”. Release the PTT and the radio beeps to confirm to other users that your transmission has finished ( ‘Roger Beep’, see paragraph).
VOX function and its sensitivity The VOX function lets you open the transmission by voice without the use of the PTT button. To get the most use from the VOX feature you must first determine what sensitivity (noise level) is needed to activate the VOX. Push the Menu button until “VOX” blinks on the display. Select the desired VOX level by means of the ▲/▼ buttons . Press the PTT or wait 3 seconds as confirmation.
To activate 1 of 38 different CTCSS/83 DCS tones in RX and TX 1. Turn on the radio. 2. Select the desired channel. 3. Press twice MENU until the Display shows oF (blinking on the right side). 4. By pushing the ▲/▼ controls the display will show CTCSS (blinking) or 5. DCS (blinking); press MENU to enter the CTCSS or DCS tones. Now 6. select the desired tone with the ▲/▼ keys. 7. To confirm the setting, press the PTT key or wait for approximately 5 seconds.
MON/SCAN Monitor function When this feature is activated, the radio can receive very low and weak signals. This is very useful when you need to talk but the distance is as far as the maximum range possible; with the monitor feature you can extend the coverage of the radio. The disadvantage is the reception of loud background noises. Activation/Deactivation: Keep pressed MON/SCAN till the display shows “Rx”. SCAN function The SCAN mode monitors the busy channels.
bars of the icon will be steady. We recommend to disconnect the power supply (disconnect the USB cable). the USB cable must be connected to devices with a charge current of 500mAh at least. Auto power save XT50 PRO is supplied with an automatic current economy circuit. If the transceiver receives no signal for more than 10 seconds, the “power save function” automatically activates. The battery life may increase by up to 50 %.
Technical specifications Channels........................................................................85: 69 LPD+16 PMR446 Frequency range.......................... 446.00625 ÷ 446.09375MHz (PMR446) ............................................................................. 433.075 - 434.775MHz (LPD) Channel spacing.................................................12.5 KHz (PMR); 25 KHz (LPD) Power supply....................................................................... 700mAh battery pack ........
Prodotto o importato da: MIDLAND EUROPE srl Via. R.Sevardi 7, 42124 Mancasale - Reggio Emilia Italia - www.midlandeurope.com L’uso di questo apparato può essere soggetto a restrizioni nazionali. Prima dell’uso leggere attentamente le istruzioni. Produced or imported by: MIDLAND EUROPE srl Via. R.Sevardi 7, 42124 Mancasale - Reggio Emilia - Italy. Imported by: Alan-Nevada UK Unit 1 Fitzherbert Spur Farlington Portsmouth Hants. P06 1TT - United Kingdom - www.nevada.co.
