DUAL BAND PMR446/LPD WALKIE-TALKIE › Instruction Guide up to 12Km* * Depending on terrain XT70 PRO
Main functions • Dual Band LPD/PMR446 transceiver Channels: 32 PMR446 (16+16 pre-programmed) + 69 LPD • Waterproof IPX4 • Emergency function • Side Tone: end transmission noise muffler • Wide LCD display with backlight • Low battery indicator • Auto power save: automatic current economy circuit • 38 CTCSS and 104 DCS tones in TX and RX • CALL button with 10 tones selectable • RRM channel (only for Italy) • Battery life up to 12 hours • Fast charger (3h) • Monitor function • Baby Sitter function • Buttons fo
Content of the package • • • • • 2 transceivers with belt clip 1 wall adaptor 1 double fast desktop charger 2 rechargeable battery packs 700mAh 2 earphone mikes MA21L (only in the Hobby&Work version) Coverage (referred to PMR frequency band) The maximum range depends on terrain condition and is obtained during use in an open space. The only limitation to maximum possible range are environmental factors such as blockage caused by trees, buildings, or other obstructions.
Identifying the parts Display 3 12 13 2 4 14 5 VOX PMR EMG HL RX TX DCS CTCSS 6 7 8 9 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
RX TX S CTCSS Transceiver 1 2 VOX PMR EMG HL RX TX DCS CTCSS PTT SPK MIC CHG 3 4 5 6 CALL MENU MON 8 SCAN 5 7 VOX PMR EMG HL PTT RX TX DCS CTCSS SPK MIC CHG 10 9 CALL MENU MON SCAN VOX PMR EMG HL RX TX DCS CTCSS 11 VOX PMR EMG HL 4| RX TX DCS CTCSS XT70 PRO user’s manual
Antenna OFF/VOLUME knob - To switch on/off the radio and to adjust the volume. 3. MENU - Press shortly this control to enter the radios menu. Keep it pressed for 3 seconds to send out the emergency call. 4. CALL/ – to send a call to the selected channel. If you keep it pressed for about 3 seconds, the keypad lock is activated. 5. ▲/ -▼ controls - To change the settings in the menu. If you keep pressed ▲/ you manually verify if there are some radios within the range (manual Out of range function). 6.
Recharging the NIMH battery pack PB70 PRO 700 mAh Place your transceiver into the cradle of the desktop charger. A complete recharge takes about 3 hours. There’s no evidence when the recharge is finished, therefore we suggest you detach the wall adaptor from the radio or remove XT70 PRO from the desktop charger cradle after 4 hours. Recharging process While the radio is being charged, the battery icon on the display will be blinking.
Basic operations Turning on/off To turn on the transceiver, turn the VOLUME knob clockwise until you hear it clicks: the LCD display will light up and do an Auto-Test. Subsequently you will hear 2 beeps of different tones. To turn off the transceiver, turn the knob counter-clockwise until you hear another click. Volume control Turn the knob VOLUME to about half way and adjust it to a comfortable level as soon as you receive a signal.
Transmitting TOT Setting The TOT function is used to prevent a too long transmission. This function temporarily blocks transmissions if the radio has been used beyond the maximum time permitted. Once reached the preset timer (180 seconds), the radio will be forced in reception mode. MON button (Monitor) The Monitor button is for temporarily excluding (opening) the squelch, in order to listen to signals that are too weak to keep the squelch permanently opened.
With the ▲/▼ buttons select “bl on” and confirm by pushing PTT or wait for 4 seconds. Keypad lock Keep pressed CALL/ for about 3 seconds and will be displayed as confirmation. Only PTT and CALL/ remain active. To disable this function, keep pressed again CALL/ for 3 seconds approx. Power Save The battery power saving feature enables a reduction in the consumption of up to 50%; power saving comes on automatically when the transceiver does not receive any signal for more than 5 seconds.
CTCSS/DCS tones selection XT70 PRO can receive in two modes: a. Open traffic: in this case you will hear any communication transmitted on the selected channel; b. Group mode CTCSS/DCS: CTCSS/DCS tones are access keys that allow you to receive only messages coming from parties using the same channel and code. The speaker will remain muted until the correct tone is received. To activate 1 of 38 different CTCSS/104 DCS tones in RX and TX 1. Turn on the radio. 2. Select the desired channel. 3.
• 9 = low sensitivity (useful in very noisy areas or if you talk loudly) All these options can be selected on two levels as follows: 1. To activate VOX function press the MENU button till VOX will appear on the display. 2. Use the scroll ▲/▼ buttons to select the desired setting: OFF: Disabled; 3. 1,2,3,4,5,6,7,8,9. Level 1 is the most sensitive 4. Press PTT to confirm or wait for 5 seconds. To disable the VOX function follow the instructions above and select option oF.
Automatic Out-of-Range By setting this mode a pair of XT70 PRO is transmitting every 30 seconds a data control code. As soon as the contact between both units is getting lost and one radio doesn’t receive this data control code, the icon starts flashing in the display and you will hear a beep tone. Automatic Out of range Activation: Press MENU till the display shows “Or of”, select “Or on” (activated) with the ▲▼ buttons. Confirm the setting by pushing the PTT or wait for 5 seconds. The display will show .
This unit set on one of these baby channels, should be placed near the baby; while the one used for listening to the baby should be set on the sitter channels “p” (from s1 to s9). In the baby channels you can set with the MENU button the VOX sensitivity level from 1 (highest sensitivity) to 9 (lowest sensitivity). See par. “VOX function”. With the MENU button it is also possible to change the baby or sitter channel and select the high (H) or low (L) power.
If you set the squelch at the highest level, you will only hear the strongest signals. 1. In PMR446 band, press the MENU button for three times. 2. The display will show “SL” followed by a number that identifies the squelch level. 3. Select the desired level by pushing the ▲/▼ controls, then confirm with PTT (or wait for 4 seconds). Troubleshooting and radio reset Your Midland XT70 PRO is designed to provide you with years of optimal performance.
Technical specifications Channels...................................................................................... 32 PMR; 69 LPD Frequency range....................................446.00625 ÷ 446.19375MHz (PMR) ............................................................................. 433.075 - 434.775MHz (LPD) Channel spacing.................................................12.5 KHz (PMR); 25 KHz (LPD) Power supply.............................................................
Prodotto o importato da: MIDLAND EUROPE srl Via. R.Sevardi 7, 42124 Mancasale - Reggio Emilia Italia - www.midlandeurope.com L’uso di questo apparato può essere soggetto a restrizioni nazionali. Prima dell’uso leggere attentamente le istruzioni. Produced or imported by: MIDLAND EUROPE srl Via. R.Sevardi 7, 42124 Mancasale - Reggio Emilia - Italy. Imported by: Alan-Nevada UK Unit 1 Fitzherbert Spur Farlington Portsmouth Hants. P06 1TT - United Kingdom - www.nevada.co.
