XT·30 WALKIE-TALKIE PMR446 * Depending on terrain › Instruction Guide up to 6Km* Downloaded from www.Manualslib.
| Downloaded from www.Manualslib.
Main functions • • • • • • • • • • • • • • • • Frequency: 446.00625 – 446.
Above all….Safety! Warnings ! Do not open the radio for any reason! The radio’s precision mechanics and electronics require experience and specialized equipment; for the same reason, the radio should under no circumstances be realigned as it has already been calibrated for maximum performance. Unauthorized opening of the transceiver will void the warranty. ! Do not use detergents, alcohol, solvents, or abrasives to clean the equipment. Just use a soft, clean cloth.
CALL CALL XT10 XT10 XT10 Description of the controls and PTT PTT functions PTT MENU MENU CALL 2 3 MON MON MENU SCAN SCAN 4 MON SCAN 1 5 6 7 XT10 PTT SPK 10 MIC 17 PTT MON SCAN SPK SPK PTT PTT MENU MIC MIC CALL XT30 9 XT30 XT30 8 12 16 CALL CALL MENU MENU CALL MON MON MENU SCAN SCAN MON SCAN 13 14 11 13 19 18 15 XT30 PTT |5 XT-30 instruction guide Downloaded from www.Manualslib.
VOX function activated Appears when the keypad lock is activated Battery level It is displayed when the radio is receiving a signal Appears when the radio is transmitting (PTT pressed) Indicates the selected CTCSS tone Indicates the selected channel Antenna LCD Display SPK/MIC jack. Jack for the connection to external accessories such as microphones, headsets, etc 11. MON/SCAN. With this button you can enable/disable the Scan and Monitor functions 12.
Let’s communicate! To turn on/off the radio Hold down MENU/ for 3 seconds. Channel selection Press once the Menu button and then select the desired channel by the ▲/▼ buttons. Press PTT to confirm the selection. Remember that both radios must be set on the same channel. Transmission Keep pressed the PTT button. The display will show “Tx” and “to”. Release the PTT and the radio beeps to confirm to other users that your transmission has finished ( ‘Roger Beep’, see paragraph).
Menu button The following functions can be selected by pressing the Menu button: • VOX • Roger Beep on/off • Channel setting • CTCSS tone setting • Keypad Beep VOX function and its sensitivity The VOX function lets you open the transmission by voice without the use of the PTT button. Push the Menu button for three times; “VOX” blinks on the display. Select ‘on’ by means of the ▲/▼ buttons and wait 3 seconds as confirmation. To disable the VOX mode Press the Menu button for three times.
Channel setting Press once the Menu button and then select the desired channel by the ▲/▼ buttons. Press PTT to confirm the selection. CTCSS sub-audio tone setting The CTCSS sub-tones, are code numbers (from 1 to 38) that can be added to the first 8 channels in order to create a new private channel. You can add up to 38 codes to the channels named from P1 to P8.
MON/SCAN Monitor function When this feature is activated, the radio can receive very low and weak signals. This is very useful when you need to talk but the distance is as far as the maximum range possible; with the monitor feature you can extend the coverage of the radio. The disadvantage is the reception of loud background noises. Activation/Deactivation: Keep pressed MON/SCAN till the display shows “Rx”. SCAN function The SCAN mode monitors the busy channels.
Insert the batteries into the radio. Plug the USB supplied in the package into the USB port of the radio. The icon with its bars will be displayed to indicate that the radio is being charged. Once the batteries are fully charged the bars of the icon will be steady. We recommend to disconnect the power supply (disconnect the USB cable). Note: the USB cable must be connected to devices with a charge current of 500mAh at least. Auto power save XT30 is supplied with an automatic current economy circuit.
Troubleshooting and radio reset XT30 is designed to provide you with years of optimal performance. If for some reason problems arise, refer to this chapter before contacting a service centre in your region. Reset If your transceiver experiences a logical malfunction (improper symbols on the display, blocking of functions, etc.), it may not be experiencing a true failure, but rather a problem caused by external factors.
Technical specifications Channels...................................................16 PMR446 (8 + 8 pre-programmed) Frequency............................................................ 446.00625 - 446.09375MHz Channel spacing..........................................................................................12.5 KHz Power supply...................................... 3 x AAA rechargeable batteries 300mAh ....................................................................................
Prodotto o importato da: CTE INTERNATIONAL s.r.l. Via. R.Sevardi 7- 42124 Reggio Emilia Italia www.midlandeurope.com L’uso di questo apparato può essere soggetto a restrizioni nazionali (per l’uso in Italia, è richiesta una dichiarazione di possesso). Prima dell’uso leggere attentamente le istruzioni. Produced or imported by: CTE INTERNATIONAL s.r.l. Via. R.Sevardi 7 42124 Mancasale Reggio Emilia Italy Imported by: ALAN - NEVADA UK Unit 1 Fitzherbert Spur Farlington Portsmouth Hants.