Operating and installation instructions for condenser tumble dryer PT 7135 C Vario To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed, commissioned and used for the first time. en - GB M.-Nr.
Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags, etc are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation.
Contents Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operating the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Before using for the first time . . . . . . . .
Contents Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Check and fault messages in the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 An unsatisfactory drying result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Other problems . . . . . . . . . . . . . . . . . . . .
Warning and Safety instructions ~ It is essential to read these instructions. This tumble dryer complies with current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the tumble dryer, please read these instructions carefully before using it for the first time. They contain important information on its safety, installation, use and maintenance.
Warning and Safety instructions ~ The tumble dryer can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, if they are are supervised whilst using it or have been shown how to use it in a safe way and recognise and understand the consequences of incorrect use. ~ Children under 8 years of age must be kept away from the tumble dryer unless they are constantly supervised.
Warning and Safety instructions ~ The tumble dryer may only be operated when the following conditions are met: – the ship’s hull is longer than 28 metres. – the list of the vessel is not more than 2°. – any external vibration is no more than 150 Hz at an amplitude of 0.35 mm. The safe operation and correct functioning of the tumble dryer can only be guaranteed if the above conditions are met. ~ The tumble dryer may not be operated on an open deck.
Warning and Safety instructions ~ The electrical safety of this tumble dryer can only be guaranteed when correctly earthed. It is essential that this standard safety requirement is met. If in any doubt, please have the electrical installation tested by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock). ~ Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability.
Warning and Safety instructions ~ Please observe the instructions in "Installation and connection" and "Technical data". ~ The socket must be easily accessible after installation in order to disconnect the tumble dryer from the electricity supply. ~ For hard-wired machines, the all-pole isolator provided on-site must be easily accessible after installation in order to disconnect the tumble dryer from the electricity supply.
Warning and Safety instructions Correct use ~ The maximum load of dry laundry for this tumble dryer is 6.5 kg. See the Programme chart for the maximum recommended loads in individual programmes. ~ Do not let anyone sit or lean on the door, as this can cause the tumble dryer to tip up. Danger of injury. ~ Always close the door after use. This way you will avoid the danger of: – children climbing into the dryer or hiding things in it. – pets or other small animals climbing into it.
Warning and Safety instructions ~ The dryer must not be used without the fluff filters in place or if the fluff filters are damaged in any way. Damaged filters can cause operational faults and blockages in the airways, condenser unit and heating elements. Fire hazard. In the event of a damaged filter, switch the dryer off and replace the filter with a new one. ~ The fluff filters must be cleaned regularly. ~ The dryer must not be used without the condenser unit in place.
Warning and Safety instructions ~ To prevent the risk of fire, the following textiles must not be dried in this tumble dryer: – items which have not been washed. – items, such as workwear, which have not been thoroughly cleaned and which are still soiled with grease, oil or other deposits (such as cosmetics, lotions etc). If items have not been thoroughly cleaned there is a danger that these might self-ignite when heated, even after they have been removed from the dryer at the end of the programme.
Warning and Safety instructions ~ Danger. This tumble dryer must not be connected to a controllable socket (e.g. a timer switch or a peak load shut-off device). If the dryer programme were to be interrupted before the end of the cooling down phase, the laundry could self-combust. ~ To prevent the risk of fire, the following must not be tumble dried: – items which have been cleaned using chemicals (e.g. professional dry-cleaning agents).
Warning and Safety instructions ~ Benzine, petrol, paraffin or any easily flammable liquid must not be stored or used near the tumble dryer. Danger of fire and explosion. ~ Do not allow air contaminated with chlorine, fluorine or other vapours containing solvents to get into the tumble dryer. Fire hazard. ~ For tumble dryers with stainless steel surfaces: The stainless steel surfaces must not come into contact with liquid cleaning and disinfecting agents which contain chlorine or sodium hypochlorite.
Warning and Safety instructions Accessories ~ Only use genuine Miele original spare parts and accessories with this tumble dryer. If non-Miele parts are used, guarantee, performance and product liability claims may be invalidated. ~ A Miele tumble dryer can be stacked on top of a Miele washing machine using the appropriate stacking kit (available as an optional accessory). Please make sure you order the correct one for the Miele tumble dryer and Miele washing machine.
Operating the tumble dryer Control panel a Display After the machine has been switched on, the display lights up. As soon as the dryer is ready to use, the Entry menu appears in the display. b Short cut buttons (keys) For selecting an individual drying programme quickly. These buttons can be programmed to select your own favourite drying programmes. c Start button The indicator light flashes when a programme can be started and lights up when the programme starts.
Operating the tumble dryer Display Entry menu 1 Cottons Programme selection ... 2 Minimum iron Settings F ... 3 Woollens handcare 4 Smoothing 10:00 When the tumble dryer is switched on, the entry menu (with four favourite programmes listed) appears with Programme selection highlighted. Multi-function selector Turning the multi-function selector moves the highlighting to the next option. Pressing the multi-function selector selects the highlighted option.
Operating the tumble dryer Programme selection menu Programme selection Back A Cottons Minimum iron Delicates H You can use the multi-function selector to select any programme. The highlighting will move up or down depending on the direction the multi-function selector is turned in. The HV arrows on the right of the display, indicate further options. Pressing the multi-function selector takes you to the main menu of the programme selected.
Operating the tumble dryer Operating the tumble dryer in Laundrette mode The entry menu will vary depending on the Controls setting selected. ^ The dryer is operated either with shortcut buttons D, E, F, G or the multi-function selector. WS-shortcut keys, basic 1 Cottons Normal+ 2 Minimum iron Normal 3 Woollens handcare 4 Cool air 4 programmes are available to choose from. To specify which programmes are available go to the Settings/supervisor level menu.
Notes and tips on laundry care 1. Sort the laundry Garment care label symbols Drying q Normal/higher temperature r Reduced temperature: Select Low temperature (for delicate textiles) s Do not tumble dry Ironing I Very hot H Hot G Warm J Do not iron Before drying – Wash heavily soiled items very thoroughly, ensuring that you use sufficient detergent and select a high temperature. If in doubt, wash the items several times.
Notes and tips on laundry care 2. Load the tumble dryer ,Using the tumble dryer incorrectly could cause a fire. Read the "Warning and Safety instructions" before using the tumble dryer. ,Make sure that objects, e.g. detergent dispensing balls, have been removed from the laundry. They could melt and cause damage to the dryer or the laundry. – Do not overload the drum. Overloading can cause unnecessary wear and tear to the laundry, give a disappointing drying result and cause more creasing.
Short instructions A Sort the laundry ,It is very important to read the "Notes and tips on laundry care" section before proceeding. B Load the tumble dryer ,To avoid damaging your laundry, when shutting the door check that no items of laundry have become trapped in the door opening. ^ Open the door. ^ Load the drum. 22 ^ Shut the door either with a gentle swing, or lean against it and push it shut.
Short instructions C Select a programme ^ Switch the dryer on by pressing the On/Off K button. Please note: – If no further selection is made within 15 minutes, the dryer will switch off automatically. – This does not apply to machines with a payment system. Programme chart – See separate booklet "Commissioning, Programme chart and Settings". You can select a programme either by: 2. Selecting a programme from the Programme selection menu (turn A and press B).
Short instructions D Start the programme – Interruption to the power supply The Start button will flash as soon as a programme can be started. – Time remaining ^ Press the Start button. Programme duration/Estimated time remaining The Start button will now light up. – Prog. running will appear in the display, followed by Drying and the programme duration. – With sensor drying programmes, e.g. Machine iron ... Hand iron etc., the drying level reached will be shown in the display later on.
Short instructions E Remove the laundry when the programme has finished Anti-crease (if selected) and Finish will appear in the display to indicate that the programme has finished. Please note: – To avoid creasing, during the anti-crease phase the drum will continue to turn at intervals until the laundry is removed. – The dryer will switch off automatically 15 minutes after the end of a programme/the end of the anti-crease phase. It is advisable to remove laundry as soon as the programme has finished.
Selecting a programme Selecting/changing a programme Entry menu 1 Cottons Programme selection ... 2 Minimum iron Settings F ... 3 Woollens handcare 4 Smoothing 10:00 ^ Press shortcut button D. Main menu Cottons Normal Duration 0:50 h Low temp. Timer Y Save Back A H H H H ^ By turning the multi-function selector you can then highlight the following options in the display: Programme (Cottons) or the drying level (Normal), and confirm your selection by pressing the multi-function selector.
Selecting a programme Note: If you do not make a selection in the sub-menu within approx. 20 seconds, the display will revert to the main menu. – Programmes with drying levels Cottons Normal+ Drying levels from Machine iron - Extra dry c ^ Use the multi-function selector to select the drying level you want, and confirm your selection. – The display will show which drying levels can be selected for each individual programme.
Selecting a programme Low temperature Select Low temperature for all delicate or minimum iron fabrics with the r care label (e.g. acrylic garments). – Delicate fabrics are dried at a lower temperature. – The programme duration is longer. ^ Press shortcut button D Low temp. Saving a favourite programme You can programme the shortcut buttons to call up the four most frequently used drying programmes.
Timer Depending on the Delay start setting, you can use the Timer to set the time you wish a programme to finish or start at, or you can delay the start of the programme. To open the Timer sub-menu Cottons Normal+ Low temp. Duration 1:06 h Low temp. B Timer Y Save Back A H H H H ^ Use shortcut key E Timer to open the Timer sub-menu. To select a delay start time Cottons Normal+ Low temp.
Changing the programme sequence Payment system Opening the door or cancelling the programme after it has started may cause a loss of credit (depending on how the tumble dryer was set up)*. * Either during the commissioning process or subsequently, a Miele service technician can re-set the payment system so that programming changes can be made. Once a programme has started - changing the programme You cannot change to another programme once a programme has started (this prevents unintentional alterations).
Cleaning and care Cleaning the fluff filters Fluff from items being dried is collected by the fluff filters in the door and the door opening. Clean the filters after each drying programme*. Cleaning them whilst dry ^ Remove any fluff from the hollow part of the door opening. You could also use a cleaning brush which is available as an optional extra from your Miele dealer or the Miele Spare Parts Department or use a vacuum cleaner.
Cleaning and care Cleaning them with water If there is a great deal of compacted fluff on any of the filters, they can be removed and cleaned under hot running water. ^ Open the door and pull the fluff filter out of the door as described previously. The two filters in the door opening can also be removed if you need to clean them with water. Replacing the filters ,Do not replace the filters if they are damp or wet. Damp or wet filters could cause operational faults.
Cleaning and care Cleaning the tumble dryer ,Disconnect the tumble dryer from the mains electricity supply. ,Do not use solvents, abrasive cleaners, glass cleaners or all-purpose cleaners. These could damage plastic surfaces and other parts. ,The tumble dryer must never be hosed down. ^ Clean the housing and the control panel with a slightly damp cloth and a mild detergent or soapy water.
Cleaning and care Cleaning the heat exchanger ,Check the heat exchanger unit regularly. It should always be cleaned immediately the Clean condenser unit or Clean out airways message appears. Removing the heat exchanger ^ Turn the lever on the inner cover downwards to the vertical position. ^ Pull the cover forwards. ^ Remove it by pulling it diagonally upwards. ^ Open the access panel. The hooks at the side will prevent the panel from falling off. ^ Now remove the panel by pulling it diagonally upwards.
Cleaning and care If you can see some fluff: ^ Clean the condenser unit as described below. To clean the condenser unit ^ Use a shower head or similar to rinse the unit out as shown. ^ Pull the condenser (heat exchanger) unit out of its housing by the handle. Checking the condenser unit (heat exchanger unit) – From the sides. ^ Hold the condenser unit up to the light as shown. ^ Check to see if there is any fluff inside it. The arrows in the illustration above indicate where to look.
Cleaning and care ^ Check the condenser unit again for any visible fluff, and if necessary flush it through again until it has all gone. ^ Also make sure the rubber seals are clean. The rubber seals must not be removed and must be free of kinks. To check and clean the condenser unit housing ^ Remove any soiling still visible inside the housing by hand using a damp cloth. Do not try and access areas you cannot reach by hand.
Problem solving guide Problem solving guide With the help of the following notes minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Service Department. ,Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous.
Problem solving guide Problem E E Possible cause Remedy There is a blockage – Confirm with OK. in the ducting system. – Clean the fluff filters. – Check all possible causes appears at the end given under "The drying of a programme.* process goes on too long or even switches off." Clean out airways Clean the filters Check ducting. Clean out airways Clean the filters Check ducting. appears after a programme has been cancelled. \ Maintenance message Clean the condenser unit.
Problem solving guide An unsatisfactory drying result Problem The laundry is not sufficiently dry. Possible cause The load consisted of different fabrics. Feathers are a natural product and this is quite normal. Items made of synthetic Synthetic fibres tend to fibres are charged with attract static charge. static electricity after drying. Feather filled pillows smell after drying. There is a build-up of fluff.
Problem solving guide Other problems Problem The drying process goes on too long or even switches off. Possible cause You might be asked to clean the airways/ducting system again. Ventilation to and from the dryer may be insufficient, e.g. because it is installed in a room which is too small. This can cause the temperature in the room to rise sharply. The vents below the door are blocked. The fluff filters are clogged up with fluff or were still wet when they were replaced.
Problem solving guide Problem Possible cause Remedy Water leaks from the dryer after the condenser unit has been cleaned. – The inner cover of the – Ensure that the condenser unit has not condenser unit is been locked properly positioned correctly and/or the condenser and lock the inner unit has not been cover. positioned correctly. – Check the rubber seals. – Fluff has collected in the condenser unit – Use a cloth to remove housing. any visible fluff from the inside of the condenser unit housing.
Problem solving guide Problem Possible cause Remedy The programme does not start and the display is dark. There is no power to the dryer. – Is the dryer switched on? – Is the door closed properly? – Has the fuse or circuit breaker tripped? When the power comes back on after a power cut, confirm with OK and start the programme again. The dryer switches off automatically after 15 minutes if no further selection is made. The display has switched off automatically to save energy: Standby.
Problem solving guide Changing the lamp Disconnect the tumble dryer from the mains electricity supply. The lamp specification and maximum wattage is stated on the data plate and on the lamp cover. ^ Open the door. ^ Replace the lamp. You will find the interior lamp cover at the top of the drum aperture. ^ To close the cover push it upwards and press it on the left and right until you hear it click into position.
After sales service Repairs PC / Optical interface In the event of any faults which you cannot remedy yourself, or if the tumble dryer is under guarantee, please contact The indicator or check light marked PC on the fascia panel is the interface used by Miele service technicians during servicing work for testing purposes and for updating the machine´s programme data. – your Miele Dealer or – the Miele Service Department (see back cover for contact details).
Installation and connection Front view a Mains connection cable b Control panel c Door d Service panel for condenser unit e Four height adjustable screw feet f External drainage options (e.g.
Installation and connection Side view View from above Rear view Washer-dryer stack a Protruding lid edge (see arrows) for holding when moving the tumble dryer. The tumble dryer can be combined with a Miele washing machine in a washer-dryer stack. A stacking kit is required which can be purchased from Miele. The stacking kit must be fitted by a Miele authorised service technician.
Installation and connection Installing the tumble dryer Levelling the machine ,Make sure the dryer door can be opened without hindrance after installation. Transporting the dryer to its installation site The machine must be perfectly level to ensure safe and proper operation. When moving the dryer, hold it by the lid where it protrudes to the rear. To manoeuvre the dryer out of its packing case to its installation site you will also need to hold it by the front feet.
Installation and connection ,Never block the vents on the dryer. In order to ensure sufficient ventilation to the dryer, do not reduce the vent gap between the underside of the dryer and the floor with a plinth, deep-pile carpet, etc. This tumble dryer is not suitable for building under. Room in which the dryer is located Air taken in for use in the drying process will be warm when it is expelled from the underside and back of the dryer. This expelled air heats up the air in the room.
Installation and connection External drainage of the condensed water The condensed water is pumped away through the drain hose which is located at the back of the dryer at the bottom. Drain hose length: . . . . . . . . . . . . . . 2 m Delivery head: . . . . . . . . . . . . . . . . . 1 m ,Do not pull on the drain hose and do not allow it to become kinked as this could damage it. Drain hose connection: ^ Remove adapter 1 and hose clip 3 behind it. 1. Direct into a sink or basin.
Installation and connection Electrical connection ,All electrical work must be carried out by a suitably qualified and competent person in accordance with current local and national safety regulations (BS 7671 in the UK). This machine is supplied with a connection cable and moulded plug (BS 1363) for connection to a 230 V mains supply. The machine must only be operated with the voltage, frequency and fuse rating shown on the data plate supplied with the machine.
Technical data Height 850 mm Width 595 mm Depth Depth with door open 710 mm 1188 mm Weight Drum volume 60.5 kg 130 l Maximum capacity Length of connection cable 6.5 kg dry weight 1600 mm Voltage Connected load Fuse rating Lamp wattage Test certificates awarded Max. load bearing in operation Product safety standard Emission sound pressure level in accordance with EN ISO 11204/11203 See data plate approx.
International Service Contacts America: +1 609 419 4376 Australia, Asia, Oceania: +61 3 9764 7880 Europe, Africa, Middle East: +49 5241 89 66 877 E-mail: service@miele-marine.com www.miele.com/marine-service Manufacturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany Alteration rights reserved/3715 M.-Nr.