Commissioning the machine, Programme chart, Settings PW 6065 Vario en - GB To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and commissioned. M.-Nr.
Contents Commissioning the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Basic programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Household . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Sport . . . . . . . . . . . . . . . . .
Contents Auto load control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Pre-wash water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Main wash water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Rinse water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Low water pressure .
Commissioning the machine Before using for the first time ,Before commissioning the machine, ensure that it is correctly installed and connected. Please follow the operating and installation instructions. ,Commissioning must be completed to determine the settings for daily operation. Certain settings can only be altered during the commissioning process. After that, these can only be changed by a Miele service technician.
Commissioning the machine To set the time of day The time may already have been set at the factory. If it has, and is correct, you can skip this section. It is possible to alter the time at any stage via the Settings menu. Settings 24 h clock... Time of day 12 h clock... Time not displayed ^ Confirm either 24 h or 12 h. If you confirm Time not displayed, the following step will be skipped.
Commissioning the machine Determining target groups By selecting target groups, you are determining the programme range of the washer-extractor. You can see which programmes are assigned to each target group under "Programme chart" later in this booklet. Settings § Beauty salons/Health spas Target groups ~ Professional cleaners V ~ Special programmes Confirm selection ^ Use the multi-function selector to select and confirm none, one or several of the target groups, as required.
Commissioning the machine Each of these settings must now be confirmed (and altered if required). More details about the settings are given under "Settings menu". Place a cross in the box 8 to indicate your selection, or fill in the gaps _____ as required. Pre-wash water This setting establishes the temperature of the water for the pre-wash. ^ Select: 8 8 The contrast for the display can be set in 10 steps. ^ Select the contrast for the display.
Commissioning the machine 8 8 IK6 Supervisor level code Serial interface RS 232 for Interface card 6 is active in coin operation mode (an IK6 module must be fitted). The Settings/Supervisor level menu can be locked with a code to prevent it being accessed by unauthorised personnel (the Language J setting can still be altered). RS 232 Serial interface RS 232 is active when the machine is operated with coins (an RS 232 module must be fitted). ^ Select the option you want.
Commissioning the machine Transit bars A message will appear in the display to remind you to remove the transport bars. ^ Remove them (if this has not already been done by your fitter). Then press the multi-function selector to confirm that this has been done. To repeat the commissioning process If you are not certain that all of the settings are correct, you will need to repeat the commissioning process. i Set up successful OK H Back A H ^ Select Back and confirm your selection.
Commissioning the machine 1 Cottons Uni. 2 Minimum iron 60°C Programme selection... 40°C Settings F... 3 Delicates 40°C 4 Woollens H 30°C 15:00 To finish the commissioning process completely, a first wash programme must be started. If the power to the machine is switched off before the first wash programme is started (e.g. by pressing the K button), the commissioning process can be carried out again.
Programme chart Basic programmes Cottons Hygiene Use for 70°C to 95°C Max. load 6.5 kg Cotton or linen fabrics, e.g. bed linen, baby clothing, underwear. Extra options Pre-wash, Starch stop, Rinse hold, Intensive*, Water plus* Detergent Cottons Uni. Universal detergent Cold to 60°C Max. load 6.5 kg Use for Cotton or mixed fibre garments, e.g. T-shirts, trousers. Note For dark coloured fabrics use a detergent for coloured fabrics, or liquid detergent.
Programme chart Delicates 30°C to 60°C Max. load 2.5 kg Use for Delicate synthetic, mixed fibre, rayon and easy care cotton garments. Note Maximum spin speed 600 rpm Extra options Pre-wash, Rinse hold, Intensive* Detergent Liquid detergent for delicates Woollens / Cold to 40°C Max. load 2.5 kg Use for Machine-washable or hand-washable wool or wool blend fabrics.
Programme chart Silks / Cold to 30°C Max. load 2.5 kg Use for Silks and other handwashable fabrics with no wool content Note Place socks, tights, bras etc. in a washing bag. Note Maximum spin speed: 600 rpm Extra options Rinse hold, Water plus* Detergent Liquid detergent for delicates Shirts Cold to 60°C Max. load 2.5 kg Use for Shirts and blouses. Tips – Pre-treat collars and cuffs if necessary. – Wash silk garments in the Silks programme.
Programme chart Proofing Cold to 40°C Max. load 3.0 kg Use for Treating microfibre fabrics, ski wear, fine closeweave cotton garments (poplin) or tablecloths with a water and dirt resistant finish. Tips – The items should be colour sorted and freshly laundered and spun or dried before proofing. – For best results, they should be heat-treated afterwards, either in a tumble dryer or by ironing.
Programme chart Household Dark garments Cold to 40°C Use for Dark garments made from cotton or mixed fibre. Tip Wash inside out. Note Maximum spin speed: 1000 rpm Extra option Rinse hold Detergent Liquid detergent for coloured fabrics Denim Cold to 40°C Max. load 3.5 kg Max. load 3.5 kg Tips – Wash denim inside out. – Denim often contains excess dye and may run during the first few washes. Wash light and dark coloured items separately.
Programme chart Sport Indoor sportswear Cold to 40°C Max. load 3.0 kg Use for Sport and fitness clothing such as shorts and tops made from synthetic or mixed fibre. Note Maximum spin speed: 800 rpm Extra option Rinse hold Detergent Liquid detergent for delicates Outdoor sportswear Cold to 60°C Max. load 3.
Programme chart Hotel Kitchen linen 40°C to 95°C Max. load 6.5 kg Use for Kitchen linen made from cotton and linen fabric, e.g. chef's whites, catering uniforms, serving cloths, cleaning cloths. Tip Select Pre-wash for stubborn soiling. Use a detergent containing enzymes for the pre-wash. Notes Includes a pre-rinse to remove coarse soiling. Extra options Pre-wash, Rinse hold Detergent Universal detergent Table linen 30°C to 60°C Max. load 3.
Programme chart Delicate curtains Cold to 40°C Max. load 2.5 kg Use for Curtains, including net curtains, specified as machine-washable by the manufacturer. Tip Select Without spin for curtains which crease easily. Note Maximum spin speed: 600 rpm Extra options Pre-wash, Rinse hold Detergent Bed linen Specialist curtain detergent, universal detergent or detergent for coloured fabric, in powder form 40°C to 95°C Max. load 6.5 kg Use for Cotton and mixed fibre bed linen.
Programme chart Disinfection Therm.DIS 15min 85°C Max. load 6.5 kg Use for Cotton and mixed fibre fabrics. Note – Thermal disinfection. – The wash cycle is followed by a disinfection phase at 85°C, with a holding time of 15 minutes. – The Without spin setting is not possible. Extra options Pre-wash Detergent Specially formulated detergent (containing bleach) CTh. DIS 10min CTh. DIS 20 min CTh. DIS 20min 70°C 60°C 40°C Max. load 6.5 kg Use for Cotton and mixed fibre fabrics.
Programme chart Hygiene Hygiene No laundry Hygiene will appear in the display if the last programme selected used a temperature below 55°C or if the Spin programme is selected. You should then run a programme that uses a temperature of at least 60°C or the Hygiene programme. To select the Hygiene programme: – Do not put any laundry into the drum, add a little detergent to compartment j and start the programme, or – Select a wash programme with a temperature higher than 60°C.
Programme chart Bakers/Butchers Flour Flour + 40°C to 95°C 40°C to 95°C Max. load 6.5 kg Use for Workwear, jackets, hats and cloths made from cotton or mixed fibres. Note – Use a detergent containing enzymes. – Select the Flour + programme for heavy soiling. Note Includes a pre-rinse to remove coarse soiling. Extra options Pre-wash, Rinse hold Detergent Universal detergent Grease and fat Grease and fat + 40°C to 80°C 40°C to 95°C Max. load 6.
Programme chart Beauty salons/Health spas Towels Cold to 40°C Max. load 5.5 kg Use for Lightly soiled cotton towels Tip For dark coloured fabrics use a detergent for coloured fabrics. Extra option Rinse hold Detergent Universal detergent Towels+ 40°C to 80°C Max. load 5.5 kg Use for Heavily soiled cotton towels Tip For dark coloured fabrics use a detergent for coloured fabrics.
Programme chart Professional cleaners WetCare sensitive Cold to 25°C Max. load 4.0 kg Use for Clothing such as suits and jackets which is not washable and which is marked with the w or h symbols. Note – After wet cleaning, items are treated in a finishing bath. – A liquid finishing agent should be used; this should be added to the fabric conditioner compartment. – Maximum spin speed 1100 rpm Extra options Rinse hold Detergent Specialist liquid detergent WetCare silks Cold to 30°C Max. load 3.
Programme chart Special programmes You can create 5 special programmes and name these. Enter their details in the table below. Example: EXTRA+ – – – – – – – Pre-wash intensive Main wash intensive Rinse 1 Rinse 2 Rinse 3 Spin Finishing agent Max. load: 6.5 kg (1) – – – – – – – (2) – – – – – – – 24 95 °C (3) – – – – – – – (4) 1400 rpm – – – – – – – (5) – – – – – – – Note The 5 special programmes have been pre-programmed with basic parameters at the factory: See "Settings/Supervisor level menu".
Relay control for external dispensing system The washer-extractor is fitted with an adapter for an external dispensing system. The external pumps are controlled by relays in the washer-extractor. The dispensing containers must be filled with the correct detergent or additive in the order specified. Do not use any detergents or agents containing chloride or acids. Pre-wash Main wash Fabric Finishing conditioner agent Cottons Hygiene R1 R2+R5 R4 - Cottons Uni.
Relay control for external dispensing system Pre-wash Main wash Fabric Finishing conditioner agent - R3 R4 - R1 R3 - R6 - R3 R4 - Kitchen linen R1 R2+R5 R4 - Table linen R1 R2+R5 R4 - Curtains R3 R3 R4 - Delicate curtains R3 R3 R4 - Bed linen - R2+R5 R4 - Pillows - R2 R4 - Therm.DIS 15min R1 R2+R5 R4 - CTh.
Relay control for external dispensing system Pre-wash Main wash Fabric Finishing conditioner agent Flour R1 R2 R4 - Flour+ R1 R2 R4 - Grease and fat R1 R2+R5 R4 - Grease and fat+ R1 R2+R5 R4 - Workwear R1 R2+R5 R4 - Workwear+ R1 R2+R5 R4 - - R2+R5 R4 - R1 R2+R5 R4 - - R2 R4 - WetCare sensitive - R3 - R4 WetCare silks - R3 - R4 R3 R3 - R4 Bakers/Butchers Beauty salons/Health spas Towels Towels+ Capes Professional cleaners WetCare intensive Pre-was
Changing default settings Default settings can be altered to adapt the machine to different requirements. Depending on the programmable status, the Settings/Supervisor level menu can be locked with a code to prevent it being accessed by unauthorised personnel (the Language J setting can still be altered). – Code not required Some settings are visible and can be changed by all operators via the Settings J menu.
Settings menu J To open the Settings menu If the Settings menu is not locked (Code not required), some of the settings may be changed. 1 Cottons Uni. 2 Minimum iron 60°C Programme selection... 40°C Settings F... 3 Delicates 40°C 4 Woollens H 30°C 15:00 ^ Select Settings J from the entry menu and confirm your selection with the multi-function selector. To select a setting Settings Back A Language F Suds cooling Time of day H ^ Select the setting you want to change, and confirm your selection.
Settings/Supervisor level menu To open the Settings/Supervisor level menu The Settings menu can be locked against unauthorised use (except for the Language option). It will then only be able to be accessed at Supervisor level by entering a code. To select a setting Settings Back A Language F Supervisor level ^ Select Supervisor level and confirm your selection. Settings Back A Supervisor level Access via code... Change code ^ Select Access via code and confirm your selection.
Settings/Supervisor level menu To confirm the code 0 0 0 Confirm code OK H Back A H ^ Confirm the code you have entered. W Code accepted Menu opened You are now in Supervisor level. You can alter the code if you want to prevent it being accessed by unauthorised personnel (see Settings, Supervisor level).
Settings/Supervisor level menu Language J The display can be set to appear in one of several different languages. To select the language you want, go to the Languages J sub-menu. ^ If the language shown is not the one you want turn the multi-function selector to highlight the one that you do want and confirm your selection. The flag after the word Language acts as a guide to prevent a language which will not be understood from being set.
Settings/Supervisor level menu Time of day First select whether you want the clock displayed as a 24 hour or 12 hour clock, or to not display it at all. Then set the current time of day. Supervisor level You can alter the access code to the supervisor level. ^ Enter the old code. ^ Enter a new code. If you select to not display the clock, the Timer can be used to delay the start by up to 24 hours, i.e. it will show how many hours until the start but not the current time of day.
Settings/Supervisor level menu Standby To save energy, the display goes out after 10 minutes and the Start button flashes slowly. Operating the multi-function selector or one of the short cut buttons switches the display back on again. You have 3 options: On Standby comes on: – if a programme is not selected after the machine has been switched on. – after a programme has started.
Settings/Supervisor level menu Special programmes You can create 5 special programmes and save these as favourite programmes with their own names. The special programmes are pre-programmed with basic settings. – Wash temperature: cold – Spin speed: without spin – Wash block: Main wash: short – Extra options cannot be selected Saving your options to memory and creating individual programmes is described in the next few pages.
Settings/Supervisor level menu ^ Confirm Delete again until the symbols you wish to delete have been removed. Save programme name: EXTRA+ _ ABCDEFGHIJKLMNOPQRSTUVWXYZ 0 1 2 3 4 5 6 7 8 9 / + - _ abc H Delete H Continue H Back A H ^ Turn the multi-function selector to move the cursor to the symbol line. ^ Using the multi-function selector, select and confirm each letter or symbol in turn to create the programme name. A maximum of 7 characters may be entered.
Settings/Supervisor level menu 2. Programme creation menu You can choose the programme's features by changing the basic settings. Enter the names of your special programmes and their basic settings into the "Special programmes" table in the "Programme chart". EXTRA+ Back A Temperature Spin speed Wash block Temperature – The temperature can be selected in 5°C steps from cold to 95°C. Spin speed – The spin speed is selected in steps of 100 from Without spin to 1400 rpm.
Settings/Supervisor level menu Favourites You can configure the 12 programmes in the basic menu for machine variant Shortcut keys + Logo (only in conjunction with Controls setting Shortcut keys + Logo). You can choose programmes from the machine´s complete range of programmes. The first three programmes listed will be allocated to shortcut keys 1 to 3. How to change a programme in the list: ^ Select Favourites and confirm your selection. ^ Select a programme from the list.
Settings/Supervisor level menu Intensive water plus You can choose whether you want the Intensive and Water plus extra options to be available for selection in the Extras menu. The machine is delivered with this setting deactivated (deselected). Water plus This setting is used to select the water intake setting for the Water plus extra option.
Settings/Supervisor level menu Main wash water You can select hot or cold water for the main wash. Hot water can only be taken in if the wash temperature is above 30°C. This setting is confirmed when the machine is commissioned. The machine will need to be set up specifically for Grey water if this option is selected. Rinse water You can select hot or cold water for the final rinse. Hot water can only be taken in if the wash temperature is above 50°C.
Settings/Supervisor level menu Water level Cottons You can increase the water level for the main wash in the Cottons hygiene and Cottons universal programmes. The machine is delivered with the Block parameters option selected (the water level will be controlled according to the data programmed on-site). Water level Min. iron You can increase the water level for the main wash in the Minimum iron programme.
Settings/Supervisor level menu PW duration Cottons The pre-wash duration can be changed in the Cottons hygiene and Cottons universal programmes. The machine is delivered with the Block parameters option selected (the wash duration will be controlled according to the data programmed on-site). Wash time Cottons You can increase the wash duration for the main wash in the Cottons hygiene and Cottons universal programmes.
Settings/Supervisor level menu Pre-wash You can choose for pre-wash to be carried out with every Cottons hygiene, Cottons universal and Minimum iron programme or to select it each time via the Extras menu. The machine is delivered with the Select via prog. menu option activated. No. rinses Cottons You can alter the number of rinses which are carried out in the Cottons hygiene and Cottons universal programmes. 2 rinses (factory default setting) 3 rinses 4 rinses 5 rinses No. rinses Min.
Settings/Supervisor level menu Spin free of charge If your machine is fitted with a payment system, you can release the Spin programme (Free of charge). The machine is delivered with this option deactivated. Demo programme This can be used by dealers to demonstrate the machine in their showrooms. When On is selected, the machine can be used, depending on its programmable status, but it is not possible to start a programme.
Settings/Supervisor level menu Controls You can change the way the machine is used with this setting. Caution: If "WS with short cut keys" or "Short cut keys + Logo" mode has been selected the Settings menu is not accessible after exiting the Settings/Supervisor level menu. You cannot then get back into Supervisor level. If you need to access it please contact the Miele Service Department.
Settings/Supervisor level menu Settings which can only be changed during the commissioning process If you wish to change any of these settings at a later stage, please contact the Miele Service Department. Payment system A coin box needs to be fitted. – No coin box – Programme operation The machine is operated using a coin box. The user purchases a wash programme. – Timed operation The machine is coin-operated using a time meter. The user purchases a time-controlled programme.
United Kingdom Miele Co. Ltd. Fairacres, Marcham Road Abingdon, Oxon, OX14 1TW Customer Contact Centre Tel: 0330 160 6600 E-mail: mielecare@miele.co.uk Internet: www.miele.co.uk Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive, Knoxfield, VIC 3180 Tel: 1300 464 353 Internet: www.miele.com.au China Miele (Shanghai) Trading Ltd. 1-3 Floor, No. 82 Shi Men Yi Road Jing' an District 200040 Shanghai, PRC Tel: +86 21 6157 3500, Fax: +86 21 6157 3511 E-mail: info@miele.