Operating instructions Heat-pump dryer To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr.
Contents Caring for the environment ............................................................................. 6 Warnings and safety instructions ................................................................... 7 Operating the tumble dryer .............................................................................. 19 Control panel ....................................................................................................... 19 How the sensor controls work ..............................
Contents Delay start/SmartStart................................................................................. 34 SmartStart ........................................................................................................... 35 Programme chart .............................................................................................. 36 Changing the programme sequence .............................................................. 40 Changing a programme once it has started....................
Contents Service................................................................................................................ Contact in the event of a fault ............................................................................. Optional accessories........................................................................................... Warranty .............................................................................................................. 63 63 63 63 Installation...............
Contents Programmable functions .................................................................................. Programming ....................................................................................................... Cottons drying levels..................................................................................... Minimum iron drying levels........................................................................... Cool-down temperature ......................................
Caring for the environment Disposing of the packaging material The packaging material is used for handling and protects the appliance from transport damage. The packaging material used is selected from materials which are environmentally friendly for disposal and can generally be recycled. Recycling the packaging material reduces the use of raw materials. Use material-specific collection points for valuable materials and take advantage of return options.
Warnings and safety instructions It is essential to read these instructions. This tumble dryer contains a refrigerant that is flammable and explosive. This tumble dryer complies with all current local and national safety requirements. However, inappropriate use can lead to personal injury and damage to property. Read the operating instructions carefully before using the tumble dryer. They contain important information on safety, installation, use and maintenance.
Warnings and safety instructions Correct application This tumble dryer is intended for use in domestic households and similar working and residential environments. This tumble dryer is not intended for outdoor use. It must be used only as a domestic appliance to dry items which have been washed in a water solution and which are marked on the manufacturer's care label as being suitable for tumble drying.
Warnings and safety instructions Technical safety Before setting up the tumble dryer, check it for any externally visible damage. Do not install or use a damaged tumble dryer. Before connecting the tumble dryer, ensure that the connection data on the data plate (fuse rating, voltage and frequency) match the mains electricity supply. If in any doubt, consult a qualified electrician.
Warnings and safety instructions Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician, otherwise any subsequent damage will not be covered by the warranty. Faulty components must only be replaced by genuine Miele original spare parts. The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used.
Warnings and safety instructions This tumble dryer is supplied with a special lamp to cope with particular conditions (e.g. temperature, moisture, chemical resistance, abrasion resistance and vibration). This special lamp must only be used for the purpose it is intended for. It is not suitable for room lighting. Replacement lamps may only be fitted by a Miele authorised person or the Miele Service Department. This tumble dryer uses a gaseous refrigerant which is condensed by the compressor.
Warnings and safety instructions The R290 refrigerant contained in this tumble dryer is flammable and explosive. If the tumble dryer is damaged, proceed as follows: - Avoid naked flames or anything which creates a spark. - Disconnect the tumble dryer from the electrical supply. - Air the room where the tumble dryer is located. - Contact the Miele Customer Service Department. Risk of fire and explosion due to damage to the tumble dryer. The refrigerant is flammable and explosive if it leaks.
Warnings and safety instructions Warning: Do not switch the dryer off before the drying programme has finished. If this is done, the laundry must be hung up or spread out to cool it down. Fabric conditioner and similar products must be used according to the instructions on the manufacturer's packaging. Remove all items from pockets (e.g. lighters, matches). The fluff filters must be cleaned after every drying cycle. The fluff filters or the plinth filter must be thoroughly dried after cleaning.
Warnings and safety instructions To prevent the risk of fire, textiles that have not been cleaned thoroughly or are still soiled with deposits of any kind must not be dried in this tumble dryer. This applies in particular to textiles that - have not been washed. - have not been thoroughly cleaned and are still soiled with grease, oil or other deposits (such as cooking oils, cosmetics, lotions, etc.).
Warnings and safety instructions To prevent the risk of fire, these textiles must not be tumble dried: - textiles that have been cleaned using chemicals (e.g. professional dry-cleaning agents) - textiles which contain a large proportion of rubber, foam rubber or rubber-like materials. For example, products made from latex foam rubber, shower caps, waterproof textiles, rubberised articles and items of clothing and pillows with foam rubber filling.
Warnings and safety instructions Always close the door after use. This way you will avoid the danger of: - Children climbing onto or into the dryer or hiding things in it. - Pets or other small animals climbing into it. The tumble dryer must not be used without fluff filters or - with damaged fluff filters, or - with a damaged plinth filter. This would cause an excessive build-up of fluff which in turn would cause a fault.
Warnings and safety instructions Using a fragrance flacon (optional accessory) Only use genuine Miele original fragrance flacons. The fragrance flacon must be stored in its packaging so please make sure you retain this. Caution. The fragrance can leak out of the flacon. Make sure that you always keep the flacon, or the fluff filter with the flacon inserted in it, in a horizontal position when carrying and do not tip or place down on any surface.
Warnings and safety instructions Accessories Only use genuine Miele original spare parts and accessories with this appliance. If non-Miele parts are used, warranty, performance and product liability claims will be invalidated. The tumble dryer can be combined with a Miele washing machine in a washer-dryer stack. The appropriate “WTV” stacking kit (available to order) to match your tumble dryer and washing machine is required.
Operating the tumble dryer Control panel a Control field The control field consists of various sensor controls, a time display and indicator lights. b Sensor controls for drying levels After selecting a drying level programme with the programme selector, the recommended drying level lights up. The drying levels that can be selected for the corresponding programme are dimly lit. c Indicator lights (These light up when necessary.) Empty the condensate container.
Operating the tumble dryer f Time display After the programme has started, the programme running time will appear on the display in hours and minutes. – When Delay start is being used, the programme running time will appear after the Delay start period has elapsed. – With most programmes, the running time displayed may vary or “jump”. The following factors, among others, affect the programme running time displayed: the quantity of laundry, the type of fabric and the residual moisture in the laundry.
Operating the tumble dryer How the sensor controls work The , , and sensor controls react to fingertip contact. If a sensor control is lit, it can be selected. If a sensor control is brightly lit, this means it is currently selected. If a sensor control is dimly lit, this means it can be selected.
Before using for the first time Installation Before using the appliance for the first time, check that you have followed all the instructions under “Installation”. Read these operating instructions, paying particular attention to the information provided under “Installation”. Removing the protective foil and stickers Remove: - Any protective film from the door - Any stickers from the front and the lid Please do not remove any labels (e.g. the data plate) which are visible when you open the door.
Before using for the first time Availability of the WiFi connection The WiFi connection shares a frequency range with other appliances (including microwave ovens and remote control toys). This can give rise to sporadic or even complete connection failures. Therefore, the availability of featured functions cannot be guaranteed. Miele@home availability The ability to use the Miele app depends on the availability of the Miele@home service in your country.
Before using for the first time Setting up Miele@home There are 2 ways of connecting: 1. Via the Miele app (default) 2. Via WPS To do so, you will need a WPS-compatible router. Logging in via the Miele app The Miele app can be used to connect to your network. Activate the WPS function on your router within 2 minutes. When you have successfully connected, will appear on the time display. Tip: If the connection has not been set up when the timeout has finished counting down, repeat the process.
Energy saving tips This dryer with heat-pump technology is designed for energy-saving drying cycles. However, you can save a little more energy with the following measures as the drying time is not extended unnecessarily. - If possible, make use of time-variable, low-cost electricity tariffs. Ask your energy supplier for information. Your tumble dryer's delay start function will be useful as you can select when during the next 24 hours you want drying to start automatically.
1. Notes on correct laundry care Points to note regarding washed laundry - When washing very heavily soiled items ensure that you use sufficient detergent and select a high temperature. If in doubt, wash the items several times. - Do not put soaking wet items into the tumble dryer. Make sure your laundry is thoroughly spun before drying. The higher the spin speed, the greater the savings that can be made in energy and time during drying.
1. Notes on correct laundry care Drying Care symbols Tip: Read the “Programme chart”, which contains a complete list of data for programmes and load sizes. Drying - Always observe the maximum recommended load size for each programme. This will mean that the energy consumption for the amount of laundry is at its most economical. Normal or higher Reduced* Do not tumble dry - Down-filled garments have linings which have a tendency to shrink, depending on the quality of the item.
2. Load the tumble dryer Loading the laundry Preventing damage to fabrics. Before loading the dryer, read “1. Notes on correct laundry care”. Checking FragranceDos If you are not using a fragrance flacon, check that the FragranceDos sockets are closed. The “Fragrance flacon” chapter describes how to use the fragrance flacon. Open the door. Remove any items that have been left inside the drum. Unfold the laundry and load loosely into the drum.
3. Select a programme and start it Switching on the tumble dryer The tumble dryer is switched on by selecting a programme, and switched off by turning the programme selector to the position. 3. Selecting a drying programme via the Wash2Dry programme selector position Turn the programme selector to Wash2Dry . If the connection is successful, ...... will flash in the display, followed by .
3. Select a programme and start it Selecting programme settings Selecting the drying level Check the “Programme chart” to see which programme you can select a drying level for and which drying level meets your requirements. - An estimated programme running time is displayed at the start of a programme for which the HygieneDry drying level has been selected. - The programme completes the normal drying process for laundry care first. The finish time counts down to 0 minutes.
3. Select a programme and start it Selecting the programme running time for Time Dry/DryFresh The programme running time can be selected in 10-minute increments. The programme running time can be between minutes and up to hours. Touch the or sensor control repeatedly until the required programme running time appears on the time display. Selecting DryCare 40 It can be used for all fabrics that are free of wool and are washable at temperatures of 40 °C and above.
3. Select a programme and start it Starting a programme Touch the flashing Start/Add laundry sensor control. Touch the Start/Add laundry sensor control to switch the indicators on again (this does not have any effect on a running programme). The Start/Add laundry sensor control lights up. Adding laundry Programme sequence You can add laundry items after the programme has started. - If Delay start has been selected, the Delay start time will start to count down first. - The programme starts.
4. Remove the laundry End of programme/Anti-crease action End of programme: lights up in the time display and the Start/Add laundry sensor control goes out. A buzzer sounds. The end of the programme is followed by the anti-crease phase, which will run for up to 2 hours. The Woollens handcare programme does not support the anti-crease function. See “Programmable functions”, “ Anti-crease”. The tumble dryer switches off automatically.
Delay start/SmartStart Selecting the Delay start function With Delay start, you can delay the start of a programme from minutes up to (hours). Delay start cannot be used with the Warm air/DryFresh programme. Start by selecting a programme with programme settings. Starting Delay start Touch the Start/Add laundry sensor control to start the Delay start function. - Delay start times of more than will count down in hours and then in minutes until the start of the programme.
Delay start/SmartStart SmartStart The SmartStart function lets you define a time period during which your tumble dryer will start automatically. The appliance will start on receipt of a signal, e.g. from your energy supplier, that indicates that the electricity tariff is particularly economical. This function is active when the SmartGrid programmable function is activated The time period can be defined between 30 minutes and 24 hours.
Programme chart All weights marked with * are based on the weight of dry laundry. Cottons max. 9 kg* Use for Cotton items such as those described under Cottons Normal with normal residual moisture. Note - Items are dried to a Normal level only in this programme. - The Cottons programme is the most energy-efficient for drying cotton items with normal residual moisture levels.
Programme chart Cottons max. 9 kg* HygieneDry Use for - Cottons and linen fabric which will be in direct contact with the skin, e.g. underwear, baby clothes, bed linen, towelling - Other hard-wearing items with specific hygiene requirements Tip Use for special hygiene requirements. Extra dry, Normal Use for Single and multi-layered cotton items, e.g.
Programme chart Woollens handcare max. 2 kg* Use for Woollen garments and fabric containing wool blends, e.g. pullovers, cardigans, tights. Note - Wool and wool blend items are only fluffed up; they are not dried completely. - Remove the garments as soon as the programme has finished. Bed linen max. 4 kg* HygieneDry, Extra dry, Normal, Hand iron Use for Bed linen, pillowcases, cushion covers Tip Use HygieneDry for special hygiene requirements.
Programme chart Proofing max. 2.5 kg* Use for Fabrics suitable for tumble drying, e.g. microfibre fabrics; skiwear; outdoor clothing; fine, close-weave cotton garments (poplin); and tablecloths. Note - With this programme, items can only be dried to the Normal level. - This programme includes an additional proofing fixing phase. - Only use proofing agents which are stated by the manufacturer as being “suitable for use on membrane fabrics”. These agents contain fluorochemical compounds.
Changing the programme sequence Changing a programme once it has started It is no longer possible to change the selected programme. This is to prevent the operation of the machine being tampered with. If you adjust the programme selector, the symbol will light up in the time display. The symbol goes out when you select the original programme. Adding or removing laundry You have forgotten something but the programme is already running. Touch the Start/Add laundry sensor control.
Condensed water container Emptying the condensed water container The condensed water is collected in the condensed water container. To prevent water from running out, keep it in a horizontal position when carrying it. Hold the condensed water container by the front panel and at the back. Empty the condensed water container after every drying programme. The indicator will light up if the maximum level of the condensed water container is reached.
Fragrance flacon FragranceDos Fragrance flacons (optional accessories) can be used to give your laundry a pleasant scent. This dryer has 2 places for inserting fragrance flacons. This gives you a choice of how to use them. - You can use both positions if you wish to change from one scent to another. You can close the fragrance flacon that you are not using. Removing the protective seal from the fragrance flacon Only hold the fragrance flacon as illustrated.
Fragrance flacon Inserting the fragrance flacon Open the door of the tumble dryer. The fragrance flacon is inserted in the upper fluff filter. They can be fitted on the left and the right hand side next the opener. Insert the fragrance flacon into the socket as far as it will go. Markers and must line up with one another. Open the cover using the tab until the tab is right at the top as shown. To prevent the accumulation of fluff, the cover of the unused socket must remain closed.
Fragrance flacon into the laundry effectively. The fragrance will also be noticeable in the room air during the process. Closing the fragrance flacon After drying, the fragrance flacon should be closed to prevent the fragrance from escaping needlessly. Turn the outer ring clockwise a little. The fragrance flacon can slip out. Turn the outer ring in such a way that markers and line up. Opening the fragrance flacon Before drying, you can select the intensity of the fragrance.
Fragrance flacon Removing/replacing the fragrance flacon Turn the outer ring counter-clockwise until markers a and b line up. Replace the fragrance flacon with a new one. When not in use, you can store the fragrance flacon in its original packaging. Fragrance flacons are available to order from Miele or online at www.mieleshop.com. Fragrance can leak. Do not lay the fragrance flacon down.
Cleaning and care Fluff filters This tumble dryer has 2 fluff filters in the loading area of the door. Both fluff filters trap fluff produced during the drying process. Pull the upper fluff filter forwards to remove it. Clean the fluff filters after each drying programme. This avoids having to extend the programme running time. Also clean the fluff filters when the indicator light comes on. To make the indicator light go out, open and close the door while the tumble dryer is switched on.
Cleaning and care Remove the fluff from the filter surface of all the fluff filters and the perforated laundry deflector. Turn the yellow dial on the lower fluff filter in the direction of the arrow (until it reaches the stop position). Push the upper fluff filter back into position until it clicks. Close the door.
Cleaning and care Use a vacuum cleaner with a long crevice nozzle attached to remove any visible fluff from the upper air flow openings. Finally, clean the fluff filters with water. Cleaning the fluff filters with water Wipe the smooth plastic surfaces of the fluff filters with a damp cloth to clean them. Flush the filters through under warm running water. Shake the fluff filters thoroughly and then dry them carefully. Ensure the filters are dry before replacing them.
Cleaning and care Cleaning the plinth filter Clean the plinth filter whenever the indicator light comes on or when the programme running time seems to be taking longer than usual. To make the indicator light go out, open and close the door while the tumble dryer is switched on. Removing the plinth filter Pull the plinth filter out by the handle. The right-hand guide pin comes out when the plinth filter is removed. The guide pin prevents the access panel from closing without the plinth filter.
Cleaning and care Cleaning the plinth filter Pull the handle out of the plinth filter. Fit the plinth filter back on the handle. Make sure it is the correct way round. Clean the plinth filter thoroughly under running water. Squeeze the plinth filter very carefully several times as you rinse it. Rinse the plinth filter until all visible residues have been removed. Use a damp cloth to remove any fluff from the handle. Damage caused by a damaged or worn plinth filter.
Cleaning and care Cleaning the plinth filter access panel Cleaning the dryer Disconnect the tumble dryer from the electrical supply. Damage due to the use of unsuitable care products. Unsuitable care products could damage plastic surfaces and other parts. Do not use any solvents, abrasive cleaners, glass cleaners, or all-purpose cleaners. Use a damp cloth to remove any fluff. Make sure that you do not damage the rubber seal when doing this. Close the heat exchanger access panel.
Problem solving guide Many malfunctions and faults that can occur in daily operation can be easily remedied. Time and money will be saved because a service call will not be needed. The following guide may help you to find the reason for a malfunction or a fault, and to correct it. Indicator lights or information on the time display triggered when a programme is cancelled Problem Cause and remedy The indicator light comes on. and flash after a programme has been cancelled, a signal sounds.
Problem solving guide Problem Cause and remedy The indicator light comes on. and continue to flash after a programme has been cancelled despite thorough cleaning. The plinth filter looks clean after thorough cleaning. However, the programme terminates and the fault message appears again. It is likely that the filter contains residue further down inside that could not be removed. To deactivate the message, turn the programme selector to the position.
Problem solving guide Indicator lights or information on the time display Problem Cause and remedy The indicator light comes on at the end of the programme. The tumble dryer is not working correctly or economically. Possible causes could be clogging caused by fluff or detergent residue. To switch off the indicator light, open and close the door (with the tumble dryer switched on). Please see “Cleaning and care” for notes on cleaning. Clean the fluff filters.
Problem solving guide Problem Cause and remedy : lights up and the programme has been cancelled, a signal sounds The laundry is unevenly distributed or has rolled up. Disentangle the laundry and remove a few items, if necessary. Switch the dryer off and then on again. Start a programme. lit and programme start is not possible. An update is available for the tumble dryer. See “Programmable functions – RemoteUpdate” for more information. lights up This is not a fault.
Problem solving guide Unsatisfactory drying results Problem Cause and remedy The DryCare 40 Extra is The room where the tumble dryer is located is too not drying the laundry warm. This has caused the DryCare process to finish sufficiently. prematurely. Ventilate the room thoroughly. To fully dry the laundry, select Warm air with the DryCare 40 Extra. The laundry is not suffi- The load consisted of different types of fabric. ciently dry. Finish drying using the Warm air programme.
Problem solving guide The drying cycle duration is very long Problem Cause and remedy The drying process goes on too long or even switches off.* The room where the tumble dryer is located is too warm. Ventilate the room thoroughly. Detergent residues, hair and fine fluff can clog the filters. Clean the fluff filters and the plinth filter. Remove visible fluff from the heat exchanger. The laundry is unevenly distributed or has rolled up. The drum is too full.
Problem solving guide Other problems Problem Cause and remedy There are humming noises The compressor is operating. These noises are quite normal and do not indicate a fault. A programme does not start No obvious cause. Connect the tumble dryer to the mains Turn on the tumble dryer Close the door Check whether the mains fuse has tripped Has there been a power cut? When power is restored any previously running programme will restart automatically.
Problem solving guide Problem Cause and remedy The drum lighting does not come on. To save energy, the drum lighting goes out automatically after a set time and after the programme starts. Switch the dryer off and then on again. To switch the drum lighting on, open the door of the tumble dryer. The drum lighting is faulty. The drum lighting is designed to last a long time and should not normally need to be replaced.
Problem solving guide Replacing the plinth filter Deformations The heat exchanger can clog up. Replace the plinth filter immediately if you see the following signs of wear before or after cleaning (optional accessory). Poor fit Deformations indicate that the filter has become blocked and worn by continuous use. The edges of the plinth filter do not sit properly and the plinth filter is out of shape. Fluff will blow into the heat exchanger unfiltered through edges that do not sit properly.
Problem solving guide Cracks, tears, indentations Fluff will blow into the heat exchanger through cracks and tears. This will, in time, cause a blockage in the heat exchanger. White residues or residues of other colours These residues arise from laundry fibres and traces of detergent components. They can be found on the front and side edges of the plinth filter. In extreme cases, they can form stubborn crust.
Problem solving guide Reactivating the plinth filter You can reactivate one or more soiled plinth filters in a washing machine. You will then be able to use the plinth filter again. Prior to reactivation, check that the plinth filter is in good order. Check the plinth filter following the instructions provided in “Problem solving guide – Replacing the plinth filter”. Replace the plinth filter if it has worn out. Wash the plinth filter(s) separately, not with any laundry items. Do not add any detergent.
Service Contact in the event of a fault Optional accessories In the event of any faults which you cannot remedy yourself, please contact your Miele dealer or the Miele Customer Service Department. Optional accessories for this tumble dryer are available from Miele or from your Miele dealer. You can book a Miele Customer Service Department call-out online at www.miele.com/service. Contact information for the Miele Customer Service Department can be found at the end of this document.
*INSTALLATION* Installation Front view a Mains connection cable e Plinth filter flap b Control panel f 4 height-adjustable feet c Condensed water container g Cooling air grille d Door h Drain hose for condensed water 64
*INSTALLATION* Installation Rear view a Protruding lid for holding when moving the appliance b Drain hose for condensed water c Hook for winding up the mains connection cable during transport d Mains connection cable Transporting the tumble dryer Danger of injury to people and damage to property caused by moving the appliance incorrectly. If the tumble dryer tips up there is a danger of injury to people and damage to property. Ensure that the tumble dryer is stable during transportation.
*INSTALLATION* Installation Installation Levelling the tumble dryer Ensure that no closeable door, sliding door or oppositely hinged door is installed that could hinder opening of the tumble dryer door in any way. Risk of fire and explosion due to damage to the tumble dryer. The refrigerant is flammable and explosive. Do not make any alterations to the tumble dryer. Take measures to protect the tumble dryer against damage.
*INSTALLATION* Installation Ventilation The cool air intake at the front of the tumble dryer must not be blocked or covered. This would hinder a sufficient intake of cool air for the heat exchanger. Do not block the gap between the bottom of the tumble dryer and the floor with plinth facings, deep pile carpet etc. This would hinder a sufficient flow of air to the tumble dryer. The hot air that is blown out from the heat exchanger warms the room air. Ensure sufficient ventilation of the room: e.g.
*INSTALLATION* Installation Additional installation requirements Slot-in This tumble dryer is suitable for pushing under a worktop. Appliance defect due to a build-up of heat. Make sure there is adequate room for warm air from the dryer to be directed away. - The appliance lid cannot be removed. - The electrical socket must be located in an accessible position near the tumble dryer. - Drying durations may increase slightly.
*INSTALLATION* Installation External condensed water outlet Note When drying is in progress, condensed water is pumped into the condensed water container through the drain hose which is located at the back of the dryer. The condensed water can also be externally drained away via the drain hose at the back of the dryer. This means that the condensed water container no longer has to be emptied. Drain hose length: 1.49 m Max. delivery head: 1.00 m Max. drain hose length: 4.
*INSTALLATION* Installation Arranging the drain hose Examples Damage to the drain hose Drainage into a sink or floor gully through incorrect handling. The drain hose can suffer damage and leak. Do not pull on the drain hose and do not stretch it or allow it to become kinked. Use the hose holder to secure the drain hose. There will be a small amount of residual water left in the drain hose. Have a container ready to collect this. Water damage.
*INSTALLATION* Installation Direct connection to a sink drain outlet Use the hose holder, the adapter, the hose clips and the non-return valve (available to purchase). Fit adapter 1 to the sink drain outlet using nut 2. The nut is usually fitted with a washer which must be removed. Attach the end of the hose 4 to adapter 1. Use the hose holder. Use a screwdriver to tighten hose clip 3 up close to the nut. Fit non-return valve 5 to tumble dryer drain hose 6.
*INSTALLATION* Installation Changing the door hinging You can change the door hinging on this tumble dryer yourself. For safety reasons the tumble dryer must be disconnected from the electricity supply before changing the door hinging. You will need: - a Torx T20 and T30 screwdriver - a flat head screwdriver or pointed pliers Hold the door securely and pull it forwards: to remove the door you will need to pull the base plate of the hinge with its 2 pins out of the dryer.
*INSTALLATION* Installation Turn the door lock through 180°. Press the door lock into openings on the opposite side of the door opening. Use a T20 Torx screwdriver to remove screw on the lock catch. Pull off the lock catch together with lock catch cover . Adjust the position of the door lock so that the screw holes line up with those in the front panel of the dryer . Secure the door lock with the two Torx screws. 3.
*INSTALLATION* Installation 4. Dismantle the door hinge from the door The door hinge cover must be unclipped from position and then removed. Insert the lock catch into the new cover supplied with the dryer. Place this new cover to one side for now. Use a screwdriver to press down gently on position on the door hinge cover. Using a little force, pull out door hinge cover . This door hinge cover is no longer needed, however, please keep it in a safe place.
*INSTALLATION* Installation 5. Change over the door hinge on the door The door hinge is secured to the door with 2 angled rods. These rods need to be removed with a screwdriver or pointed pliers. Tip: In some circumstances, the rods can be difficult to dislodge. Moving the screwdriver with a levering action while pulling at the same time may help to work the rods free. Remove the door hinge and turn it through 180°. Fit the door hinge on the opposite side of the door.
*INSTALLATION* Installation You now need the new door hinge cover supplied with the tumble dryer. Fit new door hinge cover and clip it into position. 6. Change the lock catch on the door You now need the new lock catch cover supplied with the dryer which you have already fitted with the lock catch. Push lock catch cover with its lock catch into position. Tighten screw .
*INSTALLATION* Installation Refitting Now that you have changed the 7. Refit the door door hinging the door will open from the opposite side. Press the rubber seal back into the grove on the door. Position the door in front of the dryer. Fit the base of the door hinge with its 2 pins into the openings on the dryer. The base of the door hinge must be flush with the front panel of the dryer. The door cannot fall off in this position.
*INSTALLATION* Installation Electrical connection The tumble dryer is supplied with a mains cable with moulded plug ready for connection to a suitable earthed socket. The socket must be easily accessible after the tumble dryer has been installed. If the socket is not easily accessible, ensure that a suitable means of disconnection is provided on the installation side for each pole. Risk of fire from overheating.
Technical data Height 850 mm Width 596 mm Depth 643 mm Depth with door open 1077 mm Suitable for pushing under a worktop Yes Suitable for stacking Yes Weight approx. 62 kg Drum volume 120 litres Load size 9.0 kg (weight of dry laundry) Capacity of condensed water container 4.8 l Hose length 1.49 m Maximum delivery head 1.00 m Maximum drain hose length 4.00 m Length of connection cable 2.
Technical data Data sheet for household tumble driers In acc. with delegated regulation (EU) No.
Technical data 3 4 5 6 If the household tumble drier is equipped with a power management system. This programme is suitable for drying normal wet cotton laundry and is the most efficient programme in terms of energy consumption for cotton. If the household tumble drier is a condenser tumble drier. For the standard cotton programme at full load.
Technical data EU Conformity declaration Miele hereby declares that this heat-pump tumble dryer complies with Directive 2014/53/EU. The complete text of the EU declaration of conformity is available from one of the following internet addresses: - Products, Download from www.miele.ie - For service, information, operating instructions etc: go to www.miele.ie/domestic/customer-information-385.
Consumption data Load size Cottons 2 Cottons Normal Cottons Hand iron 1 Final spin speed in Residual Energy Prowashing machine moisgramme ture running time kg rpm % kWh min 9.0 1000 60 1.55 184 4.5 1000 60 0.84 108 9.0 1200 53 1.40 166 9.0 1400 50 1.30 158 9.0 1600 44 1.15 141 9.0 1000 60 1.14 137 9.0 1200 53 1.00 120 9.0 1400 50 0.95 112 9.0 1600 44 0.80 95 Minimum iron Normal 4.0 1200 40 0.45 66 Delicates Normal 2.5 800 50 0.
Programmable functions Programming You can use the programmable functions to alter the dryer's electronics to suit your requirements. Programming is carried out by following these steps (, , ... ) using the sensor controls. Accessing the programming level Before starting - Make sure that the programme selector is turned to any of the programme settings. - Make sure that the door of the tumble dryer is open.
Programmable functions Confirm the selected programmable function by touching the Start/Add laundry sensor control. X X X = can be selected, = factory default Editing and saving a programmable function Confirm the chosen selection with the Start/Add laundry sensor control. You can either switch a programmable function on/off or select different options. The number of the programmable function (e.g. ) will then light up again.
Programmable functions Cottons drying levels You can adjust the drying levels for the Cottons programme to one of 7 different levels. Options = Even damper Cool-down temperature The laundry will be cooled to 55 °C before the end of the programme. It can be cooled to a lower temperature, but this will prolong the cooling phase. The value is set in increments of 1 °C.
Programmable functions Buzzer volume The buzzer volume can be changed. = Quieter = Factory default setting Keypad tone The buzzer that sounds when a sensor control is pressed can be changed or switched off. Selection = Off = Factory default setting = Louder Lock code The code prevents your dryer being used without your knowledge. When the code has been activated, you have to enter the code after switching the dryer on. Otherwise the dryer cannot be operated.
Programmable functions Conductivity This programmable function should only be altered if the water is so soft that it is likely to cause the electronics which sense residual moisture in the laundry to give false readings. Options = Off (factory setting) = Low Important This programmable function should only be set if the water used for washing the laundry is extremely soft with a conductivity reading (electrical conductivity) of less than 150 μS/cm.
Programmable functions Memory You can set the following: the electronic module will save the drying level and any options selected for the current drying programme. It will also save the duration of the Warm air/DryFresh programme. When the programme is selected again, these saved settings will appear in the display. Options Buzzer is active The buzzer sounds to let you know the programme has finished. It can be switched on or off.
Programmable functions Airways indicator Fluff should be removed after drying. In addition, this indicator will remind you to clean the filters when a certain amount of fluff has collected in them: You can decide at what level of fluff this reminder should be given. You will have an idea of how often this should be done after a few drying programmes. Options = Off does not light up.
Programmable functions Networking The , and programmable functions are only displayed if the requirements for using Miele@home have been met (see “Miele@home” and “Before using for the first time”). Switching off WiFi The network configuration should be reset whenever a tumble dryer is being disposed of or sold, or if a used tumble dryer is being put into operation.
Programmable functions - Some software updates can only be carried out by the Miele Customer Service Department. Postponing the update Activating/deactivating Touch the sensor control. The RemoteUpdate function is activated as standard. Available updates will be downloaded automatically but will only be installed if you initiate installation manually. Deactivate RemoteUpdate if you do not want any updates to be downloaded automatically.
Programmable functions Remote control You can use the Miele app to check the status of your tumble dryer from anywhere and start it remotely. You can also control it remotely via the MobileStart programme. Remote control is automatically activated when you connect the tumble dryer to the WiFi network. You can switch off remote control if you do not want to operate the tumble dryer with your mobile device. A programme can be cancelled via the app even if this programmable function is switched off.
Programmable functions Copyrights and licences for the communication module For the purpose of operating and controlling the communication module, Miele uses proprietary or third-party software that is not covered by open source licensing terms. These items of software/software components are protected by copyright. The copyrights held by Miele and third parties must be respected. Furthermore, this communication module contains software components which are distributed under open source licence conditions.
United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW Tel: 0330 160 6600, Internet: www.miele.co.uk/service, E-mail: info@miele.co.uk Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 Level 4, 141 Camberwell Road Hawthorn East, VIC 3123 Tel: 1300 464 353 Internet: www.miele.com.au China Mainland Miele Electrical Appliances Co., Ltd. 1-3 Floor, No.
TWH 780 WP en-GB M.-Nr.