WWF 060 Quick Start Guide
WWF 060 en - US M.-Nr. 10 669 380/01
Operation
Washing Extra options
OPERATION
WASHING
ADDING DETERGENT
Initial commissioning
Adding detergent
ɉBefore using the machine for the first
time, ensure that it is correctly installed
and connected.
Please read the separate Operating
Instructions supplied with the appliance
ɉFailure to remove the shipping struts
can result in damage to the washing
machine and to adjacent cabinetry or
appliances.
Remove the shipping struts as described
in "Installation".
Switching on the washing machine
ĺ Turn the program selector to the Normal
program.
The welcome tone will sound and the
welcome screen will light up.
The display will now guide you through the
initial commissioning, which is divided into
5steps.
For further information please refer to the
separate Operating Instructions supplied.
Operating the sensor buttons
The sensor buttons react to fingertip
contact. Selection is possible as long as
the respective sensor button is illuminated
If a sensor button is brightly lit, this means:
currently selected
If a sensor button is dimly lit, this means:
selection possible
1. Preparing the laundry
ĺ Empty all pockets.
ɉForeign objects (e.g. nails,
coins, paper clips, etc.) can
cause damage to garments and
components in the machine.
ĺ Sort the laundry by color and by care label. Most
garments have a textile care label in the collar or side
seam.
ĺ Pre-treat stains and badly soiled areas (see the booklet
"Miele's guide to laundry care").
2. Selecting a program
ĺ Turn the program selector to a program.
The interior drum lighting will come on.
Program selection
There are three possible ways to select a program:
1. Selecting the standard programs with the program
selector dial
ĺ Turn the program selector to the required program.
The selected program will be shown in the display. This
will then be replaced by the standard display.
2. Selecting additional programs by setting the
program selector to the "More programs/"
position and the display.
ĺ Turn the program selector to the More programs/
position.
The display shows: Table Linens/Drapes
ĺ Touch the sensor buttons until the program you want
appears in the display.
ĺ Confirm the program with the OK sensor button.
3. Selecting the programs via the MobileControl
program selector position and the Miele@mobile app
ĺ Turn the program selector to the MobileControl
position.
ĺ Touch the "Start⁄Stop" sensor button.
The washing machine can now be operated via a mobile
device together with the Miele@mobile app.
3. Loading the washing machine
Check the drum for pets or foreign objects before
loading it with laundry.
Opening the door
ĺ Take hold of the door and pull
it open.
ĺ Loosely load the laundry in the
drum.
Closing the door
ĺ Make sure that no items are
caught between the door and
the seal.
ĺ Shut the door.
4. Selecting program settings
Selecting a temperature/spin speed
ĺ Touch the sensor buttons above or below the
temperature or spin speed value in the display until
the temperature/spin speed you want appears in the
display. Confirm with the OK sensor button.
Selecting an extra option
There are two ways of selecting extras.
1. Directly above the sensor buttons
ĺ Touch the sensor button for the desired extra. It then
lights up brightly.
2. Via the Extras sensor button and the display
ĺ Touch the Extras sensor button.
The following appears in the display: No Extra
ĺ Touch the sensor buttons until the extra you want
appears in the display and confirm this with the OK
sensor button.
EcoFeedback
You can use the sensor button to view
an energy and water consumption forecast
for the selected wash program.
ĺ Touch the sensor button.
The estimated energy and water
consumption levels will be displayed as a
bar chart.
Level of soiling
You can specify the level of soiling of the
load.
– lightly soiled
No visible soiling or stains
– normal
Visibly dirty and / or just a few slight
stains
– heavily soiled
Soiling and/or stains clearly visible. Pre-
wash starts automatically.
Delay start/SmartStart
Delay start
With the delay start function, you can delay
the start of the program. The start of the
program can be delayed from 15 minutes
up to a maximum of 24 hours.
SmartStart
With the SmartStart function you can define
a time period during which your washing
machine will be started automatically by a
signal.
6. Starting the program
- End of the program
Starting a program
ĺ Touch the flashing Start/Stop sensor
button.
The door will lock (will appear in the display
to show this) and the wash program will
start.
Program end
The door is still locked during the Anti-
crease phase and the following will appear
alternately in the display:
End / Anti-crease
and
Press Start / Stop
ĺ Touch the Start/Stop sensor button. The
door will be unlocked.
ĺ Pull open the door.
ĺ Remove the laundry.
Check that all items have been removed
from the drum.
ĺ Check the folds
in the door seal
for any small
articles. Leave
the door slightly
open to allow the
drum to dry.
ĺ Turn the program selector to the
position. This switches the washing
machine off.
ĺ If applicable, remove the used capsule
from the detergent dispenser drawer.
Leave the detergent dispenser drawer
slightly open to allow it to dry.
Extra options
You can supplement the wash programs
with extra options.
SoftSteam
In order to reduce creasing, the laundry
undergoes a smoothing process at
the end of the program. Reducing the
maximum load by 50% will give a better
result. Please note the load information
in the display. Small loads give a better
result.
Without
SoftSteam
With
SoftSteam
Full load
Half load
Half load
Small load
Small load
Very small
load
The garments must be suitable for drying
in a tumble dryer and suitable for
ironing .
Buzzer
A buzzer sounds at the end of the
program. The buzzer will sound until the
washing machine is switched off.
Pre-wash
For laundry with large amounts of dirt,
e.g., dust and sand.
Pre-wash and Bleach are not possible.
The bleach is added too early.
Only liquid detergent may be added to
the chamber of the detergent
dispenser drawer.
Powder detergent clogs up the chamber
and water can escape from the
detergent dispenser drawer.
Gentle
Drum rotation and wash duration are
reduced. Lightly soiled textiles are washed
more gently.
Rinse plus
An additional rinse cycle can be activated
to give a more thorough wash result.
Soak
For heavily soiled textiles with stains.
A duration of between 30 minutes
and 5 hours can be chosen for the
soak process. See "Settings" for more
information.
The factory default setting is 30 minutes.
Environmentally friendly washing
– Make use of the maximum load of the
respective wash program.
– When smaller amounts of laundry
are washed, the washing machine's
automatic load control system will
reduce the amount of water and energy
used.
– Use the Express program for small,
lightly soiled loads.
– Modern detergents make it possible to
wash at lower temperatures. Using the
corresponding temperature settings will
save energy.
– For precise dispensing, use automatic
detergent dispensing.
– Select the highest possible spin speed
for the wash program to save energy in
the subsequent tumble dryer cycle.
1 Control field
The control field consists of a display
and various sensor buttons.
2 Display
Values are displayed and/or selected in
the display.
3 Sensor buttons
The values in the display can be
changed with the sensor buttons .
4 OK sensor button
Confirm the selected values with the OK
sensor button.
5 Optical interface
for service technicians.
6 Sensor buttons for extras
You can supplement the wash programs
with extra options.
7 Sensor button
You can use the sensor button to
view an energy and water consumption
forecast for the selected wash program.
8 Sensor button
The sensor button starts the delay
start function.
9 Sensor button
For selecting the level of soiling.
10 Start/Stop sensor button
Touching the Start/Stop sensor button
starts the selected program or cancels a
program that has already been started.
11 Sensor button
Activates cap dosing via the detergent
dispenser drawer.
12 Program selector
For selecting programs and for switching
off the machine.
3
1
2
4
1 Detergent dispenser drawer
2 Control panel
3 Drain filters
4 Door
5. Adding detergent
There are several options for adding
detergent to the washing machine.
Detergent dispenser drawer
This washing machine requires
high efficiency (HE) detergent
Ensure that TwinDos dispensing is
deactivated.
ĺ Pull out the
detergent drawer
and add
detergent to the
compartments.
Chlorine bleach for removing
stains or liquid detergent for the
pre-wash
Detergent for the main wash,
including Soak if selected
/
Fabric softener, liquid starch or
capsules
Using chlorine bleach
ɉChlorine bleach is a very aggressive
substance. It can cause damage to the
colors and fibers of textiles. Only use
chlorine bleach on suitable textiles.
Chlorination must be activated in the
settings before chlorine bleach is first used.
Dispensing chlorine bleach
Follow the manufacturer's instructions on
the packaging.
The extra option pre-wash must not be
selected.
ĺ Pour max. ¼ cup (60ml) of chlorine
bleach into the chamber.
The chlorine bleach is added automatically
10minutes before the end of the main
wash.
Using powder detergent
The detergent dispenser drawer contains
an insert for liquid detergent in the
compartment. This insert must be removed
to use powder detergent.
Using powder detergent in the
compartment is not possible.
CapDosing
Three different types of capsule are
available:
Contents:
Fabric care (e.g., fabric softener,
proofing agent)
Additives (e.g., detergent enhancers)
Detergent (for the main wash only)
Each capsule contains the correct amount
for one wash cycle.
Activating CapDosing
ĺ Touch the sensor button.
See "Detergent" in the Operating
Instructions for more information.