Operating and Installation Instructions Refrigerator To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Turning the appliance On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Settings . . . . . . . . . . . . . . . . . . . . . . .
Contents Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Climate Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Stainless steel panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual. Only use the appliance for its intended purpose. This appliance complies with current safety requirements. Improper use of the appliance can lead to personal injury and material damage.
IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the door closed until the appliance is completely installed and secured per the installation instructions. ~ This appliance must be installed and connected in compliance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician.
IMPORTANT SAFETY INSTRUCTIONS ~ Do not block the ventilation gaps in the plinth or the top of the appliance housing unit, as this can impair the efficiency of the appliance, increase the electricity consumption and cause damage to the appliance. ~ Never use a steam cleaner to clean the appliance. Pressurized steam could damage electrical components and cause a short circuit.
Guide to the refrigerator a Hinged door shelf b Shelves (height adjustable) c Door shelves (height adjustable) d Deli drawer e Control panel f Main switch g Humidity filters h SmartFresh drawers 7
Guide to the refrigerator Control panel a Access button "p" activates the control panel b Refrigerator c Upper SmartFresh drawer d Lower SmartFresh drawer e Temperature display X colder; Y warmer Allows you to set the desired temperature in the refrigerator f Food type(s) to be stored in the SmartFresh drawers (left: high humidity right: lower humidity) g On/Off sensor button for the SuperCool function h Sensor button for the temperature and door alarm* * Only visible when the relevant function is activa
Before use Before using for the first time Turning the appliance On/Off ^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap. Dry with a soft cloth. ^ Open the appliance door. If the appliance was transported or laid horizontally for any reason, allow it to stand vertical for at least 8 hours before turning it on. Failure to do so will affect the functioning of the appliance. ^ Turn the appliance On/Off with the main switch.
Settings Using the settings This appliance is operated with the use of touch keys activated by a finger. Depending on the zone selected, you can now: – adjust the temperature, – An available button will appear white. – select the SuperCool function or – A selected button will appear yellow. – select settings for the SmartFresh drawers by food type. For additional information, see the corresponding sections in the manual. ^ Touch the access button "p" so it turns yellow.
Settings Custom settings In the custom settings mode you can select and change functions. The function possibilities are described in the respective chapters of this manual. Function Temperature unit °C - °F (see "Setting the temperature") Turning the button sound On/Off If you prefer the buttons to be silent when touched the button sound can be turned off. Display text † ^ Touch the access button "p" so it turns yellow.
Settings ^ By touching the X button, you can choose between: = 0 : Button sound is off = 1 : Button sound is on = – : Return to menu. ^ Touch the access button "p" to confirm the setting. ^ Tap the X button until you see ; in the display. Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions should be taken.
Temperature and door alarm The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door. The alarm system is always operational, it does not need to be switched on. Temperature alarm If the temperature becomes too warm, an alarm sounds, the "alarm" indicator turns red and flashes. At the same time the affected zone flashes in the display.
Setting the temperature Setting the temperature in the refrigerator The loss of coldness is no cause for concern if it is due to the door being left open for a while, e.g. for removing or storing a large amount of food. Temperature range ^ Touch the access button "p" so it turns yellow. The temperature can be selected within the following ranges: – Refrigerator : 35 to 46° F (2°C to 8°C) ^ Touch the sensor button for the refrigerator so it turns yellow.
Setting the temperature Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ Touch the access button "p" so it turns yellow. ^ While holding down the X button, press the access button "p" once. Keep holding the X button down until the following appears in the display (approx. 5 seconds). ^ Tap the X button until † appears in the display. ^ Touch the access button "p" to confirm.
SmartFresh drawers The SmartFresh drawers provide the right combination of temperature and humidity. The result is freshness up to three times longer than in the other zones of the refrigerator. Storage temperatures For fresh foods that are not adversely affected by cold, the best range is 32° - 37°F (0° - 3°C). This helps to keep the food fresh considerably longer than in the rest of the refrigerator, spoiling is minimal. The temperature is set to approx. 35°F (1.5°C).
SmartFresh drawers Tips for storing food in the SmartFresh drawers For optimal storage conditions, it is always best to store similar foods together in one drawer. The upper SmartFresh drawer is the best place to store moisture sensitive foods. Be sure the drawers are clean and dry before placing food in them. Foods that are best stored under dry conditions – fresh fish and shellfish, meats, poultry, sausage, dairy products and deli salads.
Using the refrigerator efficiently Different storage zones Coldest area Due to the natural circulation of air in the appliance, there are different temperature zones in the refrigerator. Cold, heavy air sinks to the lowest section of the appliance. Make use of these different zones when placing food in the appliance. The coldest area in the refrigerator is directly above the SmartFresh drawers. The temperature in the drawers themselves is even colder.
SuperCool When the SuperCool function is activated, the appliance is cooled as cold and quickly as possible (to a factory-preset temperature). The SuperCool function is ideal for the rapid cooling of drinks and for refrigerating large quantities of foods. Switching on SuperCool ^ Touch the sensor button for the refrigerator so it turns yellow. ^ Touch the SuperCool sensor button so it turns yellow. In the temperature display for the refrigerator zone, the new temperature setting appears, 35°F (2°C).
Automatic defrost Refrigerator and SmartFresh drawers The refrigerator and SmartFresh drawers defrost automatically. During normal operation, condensate and frost can form on the rear wall of the refrigerator and drawers. You do not need to remove this build-up, it will defrost and evaporate automatically with the heat generated by the appliance.
Adjusting the interior fittings Moving the shelves Deli drawer The shelves can be adjusted according to the height of the food. This drawer is set on telescopic tracks. It can be pulled in and out for loading and unloading, or removed for cleaning. ^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings. ^ Open the drawer. ^ Pull the shelf forward.
Adjusting the interior fittings SmartFresh drawer Replacing the drawer These drawers are set on telescopic tracks. They can be pulled in and out for loading and unloading, or removed for cleaning. ^ Completely extend the telescopic tracks. ^ Lay the drawer onto the tracks so that it connects in the front and back. ^ Turn the safety lock back to the vertical position. ^ Slide the drawer in. ^ Open the drawer.
Adjusting the interior fittings Adjusting the door shelves Removing a door shelf For easier loading, unloading, and cleaning, the door shelves can be shifted or completely removed. ^ Slide it upward all the way to the top of the slide-rails, until it can be removed. Replacing a door shelf ^ Start at the top of the slide-rails and slide the shelf down into the desired position. Removing the hinged door shelf ^ Pull the stops upward and out of the shelf, and remove the shelf lid upward.
Cleaning and care To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance.
Cleaning and care Before cleaning Aluminum frames The shelf frames are made of aluminum. ^ Clean the frames with a mild solution of warm water and liquid dish soap. ^ Use the main switch to turn the appliance off completely. The main switch is located on the right-side underneath the control panel. ^ Unplug the power cord. ^ Remove any food from the appliance and store it in a cool place. ^ Take out any removable parts, e.g., shelves, drawers.
Cleaning and care Humidity filters The two humidity filters, located above the SmartFresh drawers, must be removed for cleaning. ^ Remove the filter mat. ^ Remove the SmartFresh drawer. ^ Clean the filters by rinsing them with lukewarm water. Do not clean in a dishwasher or washing machine. This will damage the filter. ^ Air-dry the filters. ^ Place the filters back in the filter cover.
Cleaning and care Ventilation slits After cleaning ^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed. ^ Return all shelves and accessories. ^ Place food back in the refrigerator and drawers. ^ Close the appliance door. Door seals Do not use oil or grease on the door seals. This may cause the seals to deteriorate and become porous over time. ^ Insert the plug in the socket and switch the appliance on.
Cleaning and care Changing the light bulb The lighting automatically switches off after the door has been open for approx. 5 minutes. This is not a fault. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb, always hold with a soft cloth. After the bulb has cooled for a short time it will turn on again. If the light does not come on when the door is opened briefly, the light bulb should be changed. ^ Use the main switch to turn the appliance off.
Cleaning and care Side lighting ^ Turn the light cover counterclockwise and pull out. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb, always hold with a soft cloth. ^ Pull the defective light bulb from the socket. ^ Place the new bulb in the socket. Halogen bulb type: 5 W/12 V/socket G 4. ^ Put the light cover back on and turn clockwise into place. ^ Restore power to the appliance.
Frequently asked questions With the aid of the following guide minor problems can be corrected without a service call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty. Issue Possible fault The refrigerator does The machine is not not get cold. turned on. Solution Check whether the appliance is switched on at the main switch.
Frequently asked questions Issue Possible fault Solution The compressor kicks on very frequently and for too long. The ventilation slits are covered or dusty. Clean with a vacuum or brush. The door has been opened too frequently, or a large amount of fresh food has been put in at once. Once the fridge gets down to the set temperature the compressor will turn off. The door is not closed. Check that the door has been closed properly. Issue Possible fault Solution The alarm is ringing.
Noises Normal noises What causes them Brrrrr... This noise may get louder for brief periods when the motor kicks on. Blub, blub.... A gurgling noise can be heard when the refrigerant circulates through the pipes. Click.... Clicking sounds occur whenever the thermostat turns the motor on or off. Sssrrrrr.... In multi-section and frost-free appliances, the movement of air circulating through the appliance can sometimes just barely be heard.
After sales service In the event of a fault which you cannot correct yourself, please contact – your Miele dealer or – Miele Technical Service. See back cover of the this manual contact details. When contacting Miele Technical Service, please quote the model and serial number of your appliance. This information is given on the data plate inside your appliance. Warranty For additional information, please refer to your warranty booklet.
Installation Instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and machine damage read these instructions before installation or use.
Caring for the environment Disposing of the packaging materials The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Return the packaging to your dealer.
Installation Installation site Have the appliance installed by a qualified technician, according to the enclosed installation instructions. WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. Keep the door closed until the appliance is completely installed and secured as per the installation instructions. Empty weight of your machine: K 18x3 Vi . . . . . . . . . . 419 lbs (189 kg) K 19x3 Vi . . . . . . . . . .
Installation Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after installation and that the appliance is installed in accordance with these installation instructions and and with the required ventilation openings.
Installation Base Ventilation A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements: The air intake and outlet must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis. K 18x3 Vi . . . . . . . . . . 996 lbs (452 kg) K 19x3 Vi . . . . . . . . .
Installation Stainless steel panels Side-by-side Stainless steel door panels and toe-kick covers are available from Miele. This appliance can be installed "side-by-side" with another fridge/freezer using a "Merging Kit". Custom door panels The "Merging Kit" is available from Miele. This appliance is compatible with all styles and designs of kitchen cabinetry. The total weight of the decorative panel(s) must not exceed the following: K 18x3 Vi. . . . . . . . . . . . 110 lbs (50 kg) K 19x3 Vi. . . . . .
Installation Installation with partition using the "Merging Kit" Installation with partition without using the "Merging Kit" The minimum thickness of the partition is 5/8" (16 mm). If there is a partition with a thickness of more than 6 5/16" (160 mm) between the adjacent appliances, then each appliance should be individually installed within its own niche using the mounting accessories included (the "Merging Kit" is not necessary).
Installation Adjusting the door opening angle (optional accessory) Front panel gap kit (optional accessory) Depending on the installation site, it may be necessary to adjust the door opening angle to 90°. ^ Open the door. ^ Insert the banking pin through the holes and drive in with a hammer. The door opening angle is now limited to 90°. Two adjacent furniture doors can be attached instead of one large door.
Dimensions Door dimensions (open min. 90°) K 18x3 Vi *The dimensions of the door fronts and handles will vary according to each individual kitchen. K 19x3 Vi *The dimensions of the door fronts and handles will vary according to each individual kitchen.
Dimensions Door dimensions (open min. 115°C) K 18x3 Vi *The dimensions of the door fronts and handles will vary according to each individual kitchen. K 19x3 Vi *The dimensions of the door fronts and handles will vary according to each individual kitchen.
Dimensions Niche dimensions K 18x3 Vi E*: The position of the electrical connection should not be higher than 9" from the floor. Please notice: Miele recommends to place the electrical outlet next to the appliance.
Dimensions K 19x3 Vi E*: The position of the electrical connection should not be higher than 9" from the floor. Please notice: Miele recommends to place the electrical outlet next to the appliance.
Dimensions Door front dimensions K 19x3 Vi 4" - 5 3/16" 4" - 5 3/16" K 18x3 Vi 49
Installing the appliance Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation. These installation instructions are intended for use by qualified installers. In addition to these instructions, the appliance must be installed in accordance with all local codes.
Installing the appliance Aligning the housing unit Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity. ^ Check that the cavity is square. ^ Check the location of the power outlet. The housing unit must be carefully aligned using a spirit level before installing the appliance.
Installing the appliance ,Caution! The appliance is no longer secured and may be unstable. ^ From the rear of the appliance carefully lift it from the pallet. ^ Do not remove the installation supports from the appliance door. They will be used later in the installation niche. There are transportation safety devices inside the appliance to protect the shelves and storage compartments until installation is complete. Do not remove them, or parts may be damaged. ^ Check the appliance for damage in transit.
Installing the appliance Preparing the installation niche ,Keep the appliance door closed until it is securely fastened in the niche. Tipping hazard. Because of the size and weight of the appliance, it is essential to ensure that the appliance cannot tip over once it has been mounted in the niche.
Installing the appliance Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are numbered alphabetically. The bag needed for each step will be marked with its respective letter. Anti-tip brackets The anti-tip brackets a keep the appliance safely secured in the installation niche b and prevent it from tipping. Two anti-tip brackets are recommended for each appliance.
Installing the appliance Securing an alternative anti-tip device – The beam must cover the appliance by at least 2" (50.8 mm). If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. ^ Mark the installation height (lower edge of the beam) on the rear wall of the niche. If possible, always screw the wooden beam to existing studs.
Installing the appliance Sliding the appliance into the installation space If a side-by-side installation is desired, connect the two appliances together. See the Installation Manual included with the "Merging Kit". ^ Plug the appliance into the power outlet a. The plug of the appliance should be easily accessible after installation. If the plug is not accessible after the appliance has been installed, disconnection from the power supply should be completed via the circuit breaker.
Installing the appliance Aligning the appliance ^ Align the appliance with the custom front. Important! When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. ^ Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4" (32 mm). The guide dimension of 1 1/4" (32 mm) is related to a niche height of 84" (2134 mm).
Installing the appliance Attaching the appliance to the installation niche ^ Secure the attachment plate side lugs. ^ Screw the attachment plate lugs f to the overhead furniture/fixtures. If there is no way to attach the top of the appliance, it can be attached to the sides of the installation niche. If there is a fairly large gap above the appliance, cut a wooden beam to fit exactly and place it in the gap. ^ If necessary, shorten the filler strip h to the required height.
Installing the appliance For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip: ^ Open the appliance door. ^ Take the peg from the "side-by-side merging kit" and insert it halfway into the filler strip rail on the left-side appliance. ^ Place the second filler strip on the peg and press both filler strips together. ^ Screw the attachment plate lugs k to the adjacent furniture/fixtures.
Installing the appliance Preparing the custom door ^ Open the appliance door. ^ Unscrew the installation supports l from the appliance door. ^ Loosen the remaining screws from the strips m on each side of the door, then remove. ^ Set aside the screws and side strips m - you will need them again later. ^ Remove the light switch cover (see arrow). ^ Close the appliance door. 60 ^ Measure the distance X between the bracket from the door and the overhead furniture/fixtures. ^ Loosen the two nuts.
Installing the appliance ^ Mark the distance X on the back-side of the custom door. ^ Also calculate and mark the center of the custom door Y. ^ Remove the mounting frame from the appliance door and position it according to the markings on the custom door. ^ Pre-drill the holes. ^ Tightly screw on the bracket using the pre-drilled holes: Attach the bracket to each attachment point with at least one screw.
Installing the appliance Attaching and aligning the custom door front ^ Put the angle trim m back into place and screw it completely down on both sides of the appliance door. Bag E contains spare screws for this purpose. ^ Screw the nuts o a few turns onto the threaded bolts n. Do not tighten the nuts completely. ^ Close the appliance door and check the distance to doors of adjacent furniture/fixtures. ^ Insert the angle trim m as far as it will go in the spaces provided in the mounting frame.
Installing the appliance Attaching the fixing brackets Attaching the covers (Only for appliances using the "Front panel gap kit".) The fixing brackets are used to secure the custom door front to the bottom of the appliance door. ^ To mount the cover strips on both sides of the door, click them into place from bottom to top, into the gap between the appliance door and the custom door. ^ Open the appliance door all the way. ^ Slightly loosen the screw (1.).
Installing the appliance Attaching the toe-kick cover The maximum height of the toe-kick cover is 4" (101 mm) from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance. ^ If required, cut the toe-kick cover to the required length and height. ^ Insert the cover strip into the space between the appliance and the wooden panel. For side-by-side combinations, the cover strips (on both sides of the appliance) are applied to the outermost spaces only.
Installing the appliance ^ Remove the foil from the adhesive strips. ^ Attach the toe-kick cover to the plinth. Mounting the air separator The air separator keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ Position the air separator in the center of the appliance door. ^ From below, screw the air separator firmly onto the door with the 2 screws.
Electrical connection , Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
! " " #"$%#& ' " & " % ! ! $ % " "' " '" ' ( ) * + ! # " &'& , - * , .
K 1803 Vi, K 1813 Vi K 1903 Vi, K 1913 Vi en - US, CA M.-Nr.