Operating and Installation Instructions Fridge-Freezer Combination To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the Fridge-Freezer combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Turning the appliance On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Water filter change indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Exchanging the water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Confirming the filter change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Using an external water filter . .
IMPORTANT SAFETY INSTRUCTIONS When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual. Only use the appliance for its intended purpose. This appliance complies with current safety requirements. Improper use of the appliance can lead to personal injury and material damage.
IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the doors closed until the appliance is completely installed and secured per the installation instructions. ~ This appliance must be installed and connected in compliance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician.
IMPORTANT SAFETY INSTRUCTIONS ~ After your appliance is in operation, do not touch the cold surfaces in the machine, ice cubes or frozen food, particularly when hands are damp or wet. Skin may adhere to these extremely cold surfaces. ~ Do not refreeze frozen foods which have thawed completely. ~ Do not handle frozen food or ice with wet hands. Danger of injury. ~ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
IMPORTANT SAFETY INSTRUCTIONS Disposal of your old appliance ~ Before disposing of an old appliance, first make the door latch or lock unusable. ~ Take off the doors. ~ Leave the shelves in place so that children may not easily climb inside. ~ Consult with your municipal policy on recycling. ~ Be careful not to damage any part of the pipework while awaiting disposal by: puncturing the refrigerant channels in the evaporator. bending any pipework. scratching the surface coating.
Guide to the Fridge-Freezer combination a Hinged door shelf b Shelves (height adjustable) c Door shelves (height adjustable) d Floating drawer e Control panel f Humidity filter g Main switch to turn the appliance On/Off h SmartFresh drawer i Ice maker j Water filter k Small freezer basket l Large freezer basket m Ice cube container 8
Guide to the Fridge-Freezer combination Control panel a Access button "p" activates the control panel b Refrigerator c Left SmartFresh drawer d Right SmartFresh drawer e Freezer f Temperature display X colder; Y warmer Allows you to set the desired temperature in the refrigerator or freezer section g Food type(s) to be stored in the SmartFresh drawer (left: high humidity right: low humidity) h On/Off sensor button for the SuperCool function i On/Off sensor button for the ice cube maker j Sensor button for
Before use Before using for the first time Turning the appliance On/Off ^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap. Dry with a soft cloth. ^ Open the upper appliance door. If the appliance was transported or laid horizontally for any reason, allow it to stand vertical for at least 8 hours before turning it on. Failure to do so will affect the functioning of the appliance. ^ Turn the appliance On/Off with the main switch.
Settings Using the settings This appliance is operated with the use of touch keys activated by a finger. – An available button will appear white. – A selected button will appear yellow. The selected sensor button appears yellow and depending on the zone selected additional sensor buttons may appear on the control panel. Depending on the zone selected, you can now: – adjust the temperature, – select the SuperCool function, or ^ Touch the access button "p" so it turns yellow.
Settings Custom settings In the custom settings mode you can select and change functions. The function possibilities are described in the respective chapters of this manual.
Settings ^ By touching the X button, you can choose between: = 0 : Button sound is off = 1 : Button sound is on = – : Return to menu. ^ Touch the access button "p" to confirm the setting. Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions should be taken. ^ Tap the X button until you see ; in the display.
Temperature and door alarm The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or open doors. The alarm system is always operational, it does not need to be turned on. Turning the temperature alarm Off As soon as the alarm condition is corrected, the alarm signal turns off and the affected zone stops flashing in the display. The "alarm" indicator goes out.
Setting the temperature Setting the temperature in the refrigerator and freezer sections Temperature range The refrigerator and freezer sections can be set independently of each other. – Refrigerator: 36°F to 46°F (2°C to 8°C) ^ Touch the access button "p" so it turns yellow. A temperature of 37°F (4°C) in the refrigerator section is recommended. The temperature can be selected within the following ranges: – Freezer: 7°F to -11°F (-14°C to -24°C).
Setting the temperature Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ By touching the X button you can select either Fahrenheit or Celsius for the temperature display. † 0: Fahrenheit † 1: Celsius † –: return to menu ^ Touch the access button "p" to confirm the setting. ^ Touch the access button "p" so it turns yellow. ^ Tap the X button until a ; appears in the display. ^ Touch the access button "p".
SmartFresh drawers The SmartFresh drawers provide the right combination of temperature and humidity. The result is freshness up to three times longer than in the other zones of the refrigerator. Storage temperatures For fresh foods that are not adversely affected by cold, the best range is 32° - 37°F (0° - 3°C). This helps to keep the food fresh considerably longer than in the rest of the refrigerator, spoiling is minimal.
SmartFresh drawers For optimal storage conditions, it is always best to store similar foods together in one crisper. Foods that are best stored under dry conditions – fresh fish and shellfish, meats, poultry, sausage, dairy products and deli salads. Foods that are best stored under moist conditions – fresh produce, e.g., vegetables, lettuce, herbs, mushrooms, cabbage, fruit. Remember that higher moisture levels can only be attained when the food is stored unpacked so air can circulate freely.
SmartFresh drawers If you are not satisfied with your stored food (for example the food wilts or becomes withered after only a short storage time), check the following again: ^ Store only fresh food. The initial condition of the food is most important for maintaining freshness. ^ Before storing food, clean the SmartFresh zone. ^ Very moist food should be dried off before storing it. ^ Do not store cold-sensitive food in the SmartFresh zone. ^ Remember that not all foods can be stored together.
Using the refrigerator efficiently Different storage zones Due to the natural circulation of air in the appliance, there are different temperature zones in the refrigerator. Cold, heavy air sinks to the lowest section of the appliance. Make use of these different zones when placing food in the appliance. This appliance uses a dynamic cooling feature to establish a constant temperature during cooling. As a result, the differences between temperature zones are less pronounced.
Using the freezer efficiently Freezing food Placing food in the freezer Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food. Food to be frozen can be placed anywhere in the freezer section. Never refreeze partially or fully defrosted food. Consume defrosted food as soon as possible, it will lose its nutritional value and spoil if left for too long. Do not refreeze defrosted food unless it has been cooked.
Using the freezer efficiently Defrosting Cooling drinks quickly Frozen food can be defrosted in different ways: To cool drinks quickly, switch on the SuperCool function. See "SuperCool" for more information. – in a microwave oven, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep the other food cold), – in a steam oven. Poultry It is especially important to observe proper hygiene when defrosting poultry. Never save the liquid from defrosted poultry.
SuperCool When the SuperCool function is activated, the appliance is cooled as quickly as possible (to a factory-preset temperature). SuperCool When used with the refrigerator the SuperCool function is ideal for the rapid cooling of drinks and refrigerating large quantities of food. When used with the freezer the SuperCool function is ideal for freezing large quantities of unfrozen food. The function should be switched on 4-6 hours before the fresh food is placed in the freezer. If the max.
Ice cube maker For the automatic ice cube maker to operate, it must be connected to the household water supply. See "Plumbing". Turning on the ice cube maker ^ Make sure that the ice cube container is under the ice cube maker, as far as possible. Ice cubes will not be produced unless the container is completely closed. ^ Touch the sensor button for the ice cube maker so that it turns yellow. As soon as the freezer has cooled to a freezing temperature, the ice cube container fills with water.
Automatic defrost Refrigerator section and SmartFresh drawers The refrigerator and SmartFresh drawers defrost automatically. During normal operation, condensate and frost can form on the rear wall of the refrigerator and drawers. You do not need to remove this build-up, it will defrost and evaporate automatically with the heat generated by the appliance. Freezer section The freezer section defrosts automatically. The moisture generated in the appliance collects in the evaporator.
Adjusting the interior fittings Moving the shelves SmartFresh drawer The shelves can be adjusted according to the height of the food. These drawers are set on telescopic tracks. They can be pulled in and out for loading and unloading, or removed for cleaning. ^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings. ^ Pull the shelf forward. ^ Move the shelf to the desired height, then insert the (rear) hooks into place.
Adjusting the interior fittings The divider in the drawer can also be removed for cleaning. ^ Remove the drawer. ^ Lift the divider upward and out. To re-insert the divider, slide it back down along the tracks. Important: If the divider is not in place, the SmartFresh drawer will not work properly. Replacing the SmartFresh drawer ^ Completely extend the telescopic tracks. ^ Lay the drawer on the tracks so that it connects in the front and back. ^ Turn the safety lock back to the vertical position.
Adjusting the interior fittings Adjusting the door shelves Removing the hinged door shelf For easier loading, unloading, and cleaning, the door shelves can be shifted or completely removed. ^ Pull the stops upward and out of the shelf, and remove the shelf lid upward. ^ Now remove the hinged container upward and out. Removing the storage shelf from above the drawer ^ Remove the rear finishing strip, move the glass plate slightly toward the rear, and carefully lift it upward and out.
Adjusting the interior fittings Ice cube container Small freezer basket The ice cube container is set on telescopic tracks, and can be removed for loading, unloading and cleaning. The small freezer basket can be removed for cleaning. ^ Slide the container forward until resistance is felt. ^ On both sides of the container, pull the latches (see arrow) upward and lift the container out of the freezer. ^ Slide the basket forward until resistance is felt.
Cleaning and care To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance.
Cleaning and care Before cleaning Aluminum frames The shelf frames are made of aluminum. ^ Clean the frames with a mild solution of warm water and liquid dish soap. ^ Use the main switch to turn the appliance off completely. The main switch is located on the right side underneath the control panel. ^ Unplug the power cord. ^ Remove any food from the appliance and store it in a cool place. ^ Take out any removable parts, e.g., shelves.
Cleaning and care Humidity filters The two humidity filters, located above the SmartFresh drawers, must be removed for cleaning. ^ Clean the filters by rinsing them with lukewarm water. Do not clean in a dishwasher or washing machine. This will damage the filter. ^ Air-dry the filters. ^ Place the filters back in the filter cover. ^ Put the filter cover back in place, inserting the rear hooks first. ^ Remove the SmartFresh drawer. ^ Re-insert the SmartFresh drawer.
Cleaning and care After cleaning Changing the light bulb ^ Return all shelves and accessories. The lighting automatically switches off after the door has been open for approx. 5 minutes. This is not a fault. ^ Place food back in the refrigerator section, close the appliance doors, insert the plug in the power outlet and turn the appliance on. After the bulb has cooled for a short time it will turn on again. ^ Switch on the SuperCool function for the freezer section.
Cleaning and care Side lighting Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold it with a soft cloth. ^ Turn the light cover counterclockwise and pull out. ^ Remove the defective light bulb. ^ Place the new bulb in the socket. Halogen bulb type: 20 W/12 V/socket GY 6.35. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold it with a soft cloth.
Water filter The appliance is supplied with an active charcoal filter which improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water. Additional water filters are available from Miele. It is important to change the water filter regularly. To avoid serious illness or death, do not use water that is microbiologically or chemically unsafe or of unknown quality without adequate disinfection or other treatment before or after use of a filter.
Water filter Exchanging the water filter Note: Air trapped in the system may cause water and the filter cartridge to eject forcefully. Use caution when removing. ^ Remove the cap from the used filter, 3. ^ Take a new filter cartridge out of the packaging and remove the protective cap. ^ Push the cap onto the new filter cartridge, 4. ^ Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180°, 1. ^ Pull the used filter cartridge out of the appliance, 2.
Water filter Using an external water filter ^ After the filter change the filter indicator in the display still flashes. The change must be be confirmed in the electronic. If your household water supply already has an external water filter installed, leave the standard water filter (bypass cartridge) installed in the appliance. Confirming the filter change ^ Press and hold the filter change sensor button. ^ At the same time place a finger on the access button.
Water filter State of California Department of Public Health Water Treatment Device Certificate Number 06 - 1775 Date Issued: March 10, 2006 Date Revised: April 3, 2008 Trademark/Model Designation 9000 077095 Miele 07134220 Replacement Elements 9000 077104 07134220 Manufacturer: Cuno, Incorporated The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminants: Microbiologica
Water filter Performance Data Sheet For Filter Model 07134220 Using Replacement Cartridge 07134220 This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.
Lead free certificate This product KF 1803 Vi, KF 1813 Vi (KIMBM30US) / KF 1903 Vi, KF 1913 Vi (KIMBM36US) is tested and certified by WQA against ORD0902 for California "lead free" compliance. Miele & Cie.
Frequently asked questions With the aid of the following guide minor problems can be corrected without a service call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty. Problems with temperature Issue Possible fault The refrigerator The machine is not or freezer turned on. section does not get cold. The machine is not plugged in.
Frequently asked questions Problems with temperature Issue Possible fault Solution The freezer section is too warm. The room temperature is lower than the ambient temperature for which the appliance is designed. Raise the temperature of the room. Operating the appliance in a room that is too cold will cause the cooling system to switch off for too long, causing the freezer section to become too warm. The temperature display for the freezer shows -18°C, although I have set a higher temperature.
Frequently asked questions General problems Issue Possible fault Solution Water is flowing out of Close the shut-off valve immediately. the appliance. Check whether the water Contact Miele Technical pipe in the appliance is Service. defective. Check whether the water pressure is too low. Contact a plumber. Check whether the correct Self-tapping valves and 3 water valve has been /16" (4.76 mm) saddle installed. valves reduce the water pressure and can block the pipe. The door to the This is not a fault.
Frequently asked questions Alarm / Indicator warnings Issue Possible fault Solution The alarm is ringing. The appliance door(s) have been open for longer than 5 minutes. Close the door(s). The alarm is ringing and The door is not closed. the "alarm" indicator for A large amount of food is the door or temperature being frozen at the same is flashing. time. There has been a power failure. Once the alarm condition has been corrected, the alarm will turn off and the "alarm" indicator will stop flashing.
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice cube maker will not switch on. The appliance is not plugged in. Check that the appliance is connected to the power supply. The ice cube maker is not producing any ice cubes. When the appliance is turned on for the very first time, it can take up to 10 hours for the first ice cubes to drop out of the ice cube maker and collect in the container. The appliance is not turned on.
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice cubes are small. Other domestic appliances that use water are in operation. Avoid using such items as a dishwasher, washing machine or shower at the same time. Check whether the water filter needs changing. See "Water filter" for more information. Check the water pressure. The water pressure must be between 25 and 80 psi (1.7-5.5 bar). Consult a plumber.
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice maker is not producing enough ice or the ice cubes are misshapen. Check the water pressure. The water pressure must be between 25 and 80 psi (1.7-5.5 bar). Contact a plumber. Check that the freezer temperature is not too low. See "Selecting the correct temperature". Change the water filter. See "Water filter". Check the water pressure. The water pressure must be between 25 and 80 psi (1.7-5.5 bar).
Noises Normal noises What causes them Brrrrr... This noise may get louder for brief periods when the motor kicks on. Blub, blub.... A gurgling noise can be heard when the refrigerant circulates through the pipes. Click.... Clicking sounds occur whenever the thermostat turns the motor on or off. Sssrrrrr.... In multi-section and frost-free appliances, the movement of air circulating through the appliance can sometimes just barely be heard.
After sales service In the event of a fault which you cannot correct yourself, please contact – your Miele dealer or – Miele Technical Service. See back cover of the this manual contact details. When contacting Miele Technical Service, please quote the model and serial number of your appliance. This information is given on the data plate inside your appliance. Warranty For additional information, please refer to your warranty booklet.
Installation Instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and machine damage read these instructions before installation or use.
Caring for the environment Disposing of the packaging materials The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Return the packaging to your dealer.
Installation Installation site Have the appliance installed by a qualified technician, according to the enclosed installation instructions. ,WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. Keep the doors closed until the appliance is completely installed and secured as per the installation instructions. Empty weight of your machine: KF 18X3 Vi . . . . . . . . . 455 lbs (206 kg) KF 19X3 Vi . . . . . . . . .
Installation Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after installation and that the appliance is installed in accordance with these installation instructions and and with the required ventilation openings.
Installation Base Ventilation A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements: The air intake and outlet must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis. KF 18X3 Vi . . . . . . . . . 950 lbs (431 kg) KF 19X3 Vi . . . . . . . 1,185 lbs (537 kg) To ensure that the appliance is installed securely and functions properly, the base must be flat, level and made of a hard, rigid material.
Installation Stainless steel panels Side-by-side Stainless steel door panels and toe-kick covers are available from Miele. This appliance can be installed "side-by-side" with another fridge/freezer using a "Merging Kit". Custom door panels The "Merging Kit" is available from Miele. This appliance is compatible with all styles and designs of kitchen cabinetry. The total weight of the decorative panel(s) must not exceed the following: KF 18X3 Vi Upper door . . . . . . . . . .
Installation Installation with partition using the "Merging Kit" The minimum thickness of the partition is 5/8" (16 mm). Side panels If one side of the appliance is visible, a side panel must be used. The side panel must be firmly secured to the wall, the floor and the overhead furniture/fixtures before the appliance is placed in the cavity. The dimensions of the side panel are taken from the opposite wall of the installation space.
Installation Adjusting the door opening angle (optional accessory) Front panel gap kit (optional accessory) Depending on the installation site, it may be necessary to adjust the door opening angle to 90°. Two adjacent furniture doors can be attached instead of one large door. ^ Open the door. ^ Insert the banking pin through the holes and drive in with a hammer. The door opening angle is now limited to 90°. 58 To connect these furniture doors, a metal strip can be purchased as an optional accessory.
Dimensions Door dimensions (opening angle 90°) *The dimensions of the door fronts and handles will vary according to each individual kitchen. 3 KF 18X3 Vi KF 19X3 Vi /8" (10 mm) A B 32 5/8" (829 mm) Door front max. 1 1/2" (38 mm)* 38 11/16" (982 mm) Door front max. 1 1/2" (38 mm)* C Door handle* Door handle* Door dimensions (opening angle 115°) *The dimensions of the door fronts and handles will vary according to each individual kitchen. A KF 18X3 Vi 32 5/8" (829 mm) B Door front max.
Dimensions Niche dimensions Niche width (A) KF 1803 Vi, KF 1813 Vi 30" (762 mm) KF 1903 Vi, KF 1913 Vi 36" (915 mm) 60
Dimensions Power supply and water connection 1. Power supply 2. Water connection KF 18X3 Vi KF 19X3 Vi A 15" (381 mm) 18" (458 mm) Install a pressure limiting device and water hammer arrester for inlet water pressures exceeding 80 psi.(Refer to Uniform Plumbing Code, Sections 608.2 and 609.10) Never install or operate where inlet water pressure may exceed 120 psi. ,Power bars or extension cords are not safe (risk of fire). Do not use them to connect the appliance to the power supply.
Dimensions Door front dimensions A B 5 KF 18X3 Vi 53 /16" 29 1354 mm 13/16" 758 mm 26 7/16" 672 mm KF 19X3 Vi 53 5/16" 35 3/4" 1354 mm 908 mm 26 7/16" 672 mm 4" - 5 3/16" (102 - 132 mm) 1/8" - 3/16" (3 - 5 mm) 62 C
Installing the appliance Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation. These installation instructions are intended for use by qualified installers. In addition to these instructions, the appliance must be installed in accordance with all local codes.
Installing the appliance Aligning the housing unit Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity. ^ Check that the cavity is square. ^ Check the location of the power outlet. ^ Check the location of the water connection (see "Plumbing").
Installing the appliance ,Caution! The appliance is no longer secured and may be unstable. ^ From the rear of the appliance carefully lift it from the pallet. ^ Do not remove the installation supports from the appliance doors. They will be used later in the installation niche. There are transportation safety devices inside the appliance to protect the shelves and storage compartments until installation is complete. Do not remove them, or parts may be damaged. ^ Check the appliance for damage in transit.
Installing the appliance ^ Remove the cover b. ^ Push the module into the slot until it locks into place. ^ Connect the appliance to the power supply and turn it on. After several seconds the indicator light e will come on. The indicator light will display different colors one after the other; any control light at the end indicates that the module was correctly installed. If the indicator light does not come on, installation of the module was unsuccessful. In that case, repeat the process.
Installing the appliance Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are numbered alphabetically. The bag needed for each step will be marked with its respective letter. Anti-tip brackets The anti-tip brackets a keep the appliance safely secured in the installation niche b and prevent it from tipping. Two anti-tip brackets are recommended for each appliance.
Installing the appliance ^ Now attach the installation niche to the wall. Securing an alternative anti-tip device If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. – If the installation niche is deeper than the appliance, select a beam with a larger cross section, or attach two beams. – The beam must cover the appliance by at least 2" (50.8 mm).
Installing the appliance Sliding the appliance into the installation niche If a side-by-side installation is desired, connect the two appliances together. See the Installation Manual included with the "Merging Kit". protectors where needed (not included). ^ Plug the appliance into the power outlet a. The plug of the appliance should be easily accessible after installation.
Installing the appliance Aligning the appliance ^ Align the appliance with the custom front. Important! When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. ^ Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4" (32 mm). The guide dimension of 1 1/4" (32 mm) is related to a niche height of 84" (2134 mm).
Installing the appliance Note: – The adjustment of the rear feet is aided if the appliance is lifted at the rear (tipped forward slightly). If there is no way to attach the top of the appliance, it can be attached to the sides of the installation niche. Attaching the appliance to the installation niche ^ Pull out the plate side lugs g. ^ Secure the attachment plate side lugs. ^ Screw the attachment plate lugs f to the overhead furniture/fixtures.
Installing the appliance ^ Insert the filler strip until you hear it click into place j. ^ Open both appliance doors. For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip: ^ Take the peg from the "side-by-side merging kit" and insert it halfway into the filler strip rail on the left-side appliance. ^ Place the second filler strip on the peg and press both filler strips together.
Installing the appliance Now connect the water supply to the appliance (see "Plumbing"). Preparing the custom door For best results, it is important to mount the upper door before the lower door. ^ Open the appliance door. ^ Measure the distance X between the bracket from the upper door and the overhead furniture/fixtures. ^ Loosen the two nuts. Set aside the nuts - you will need them again later. ^ Unscrew the installation supports l from the appliance door.
Installing the appliance ^ Also calculate and mark the center of the custom door Y. Please note: When attaching the mounting frame onto two adjacent doors (see "Front panel gap kit") screw into the thicker outer frames of the doors only. ^ Remove the mounting frame from the appliance door and position it according to the markings on the custom door. The bracket includes a variety of holes for the various design options of custom doors. ^ Pre-drill the holes.
Installing the appliance Attaching and aligning the custom door front ^ Align the custom door height with the threaded bolts n. ^ Now tighten the nuts o on top. This secures the appliance door. ^ Open the door and hang the custom door with the mounting frame over the threaded bolts n. To mount the custom door on the lower appliance door, simply repeat the steps under "Preparing the custom door". The position of the lower furniture door depends on the position of the upper door.
Installing the appliance Note the size of the upper custom door front: The fixing brackets are used to secure the custom door front to the bottom of the appliance door. ^ Open the appliance door all the way. ^ Slightly loosen the screw (1.). ^ Position the fixing bracket on the appliance door (2.) and pre-drill a hole in the custom door front. ^ Screw the fixing bracket securely to the custom door front (3.). ^ Tighten the screw (4.).
Installing the appliance Attaching the covers ^ To mount the cover strips on both sides of the upper and lower doors, click them into place from bottom to top, into the gap between the appliance door and the custom door. ^ Insert the cover strip into the space between the appliance and the side panel. For side-by-side combinations, the cover strips (on both sides of the appliance) are applied to the outermost spaces only. ^ Attach the light switch cover.
Installing the appliance ^ Remove the foil from the adhesive strips. ^ Insert the cover plate on the freezer compartment door. Attaching the toe-kick cover The maximum height of the toe-kick cover is 4" (101 mm) from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance. ^ If required, cut the toe-kick cover to the required length and height. ^ Attach the plinth to the appliance, and put the included cover plates in place.
Installing the appliance Mounting the air separator The air separator keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ If necessary, shorten the three parts of the air separator. ^ Insert the foam pieces back into the sides. ^ Clip the air separator, left and right of the partition, in the exhaust grille. Be sure that it clicks into place and guides the foam partition under the exhaust grille.
Plumbing All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations. Disconnect the appliance from the electrical power supply before connecting it to the water supply. Turn off the water supply before connecting the water lines to the ice cube maker. The water quality must conform to country requirements for drinking water. – The appliance is only suitable for connection to the cold water supply.
Plumbing Preparing the water connection For appliances with a hose guide The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Install the connecting pipe.
Plumbing Connecting the water supply ^ Push the union nut and seal onto the water pipe. When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Push the end of the water pipe into the appliance connection and screw on the union nut, 3. First tighten by hand. When bending the water pipe, be sure not to kink it, otherwise there is a risk of leaks and water damage. Use bending aids.
Electrical connection , Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
RemoteVision (optional accessory) Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem. For information on set-up and installation of the RemoteVision module see the "Installation" section of this manual.
RemoteVision (optional accessory) Accessing the RemoteVision control panel ^ Tap the X button until ; appears in the display. ^ Touch the access button "p" to confirm. ^ Touch the access button "p" so it turns yellow. See the table on the following page for a description of each setting in the display. ^ Note the position of the X button, but do not touch. ^ Use the Y or X buttons to select the RemoteVision options. ^ Touch the access button "p" again so it turns white.
RemoteVision (optional accessory) MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network established, no IP address assigned Solid ;# Connected to network Flashing ; < In Ad-Hoc Mode, not connected Flashing ; = In Ad-Hoc Mode, connected Selectable options Description of function ;- Back ;2 Reboot the module ;3 Reset to factory settings ;4 Enter
KF 1803 Vi KF 1813 Vi KF 1903 Vi KF 1913 Vi en - US, CA M.-Nr.