Operating and Installation manual Vented Dryer PT 7136 Plus To prevent accidents and machine damage read these instructions before installation or use. en - US M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Display function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Before using for the first time. . . . . . . .
Contents INSTALLATION INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Installation of exhaust venting . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS ,WARNING - To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: ~ Make sure that no unattended children can access the machine. There is a potential danger that children can be trapped in the drum. This may cause major injuries or the death of the child. ~ Do not reach into the dryer if the drum is moving.
IMPORTANT SAFETY INSTRUCTIONS ~ To prevent the risk of fire, the following articles must not be dried in this tumble dryer: ~ To prevent the risk of fire, the – items which have not been washed. – fabrics which contain a large amount of rubber, foam rubber or rubber-like materials. For example, products made from latex, shower caps, waterproof textiles, rubberized articles, and items of clothing and pillows with foam rubber filling, or similarly textured rubber-like materials.
IMPORTANT SAFETY INSTRUCTIONS ~ GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Guide to the dryer Control panel a Display* See the following pages for more information d Optical interface PC Allows a service technician to check and update the drying programs b Direct select buttons To select a drying program directly. You can also save "Favorite" drying programs on these buttons. e Jog shuttle Turn to select Press to confirm the selection c "Start" button f a button To open the drum door. *Contents in the display will vary with program offering.
Guide to the dryer Display function Contents in the display will vary with program offering. Main menu 1 Cottons Program selection ... 2 Minimum iron Settings F ... 3 Woollens handcare 4 Smoothing 10:00 The display shows the main menu (with factory default settings). "Program selection" is highlighted. If the display is dark (in Stand-by mode) turn the jog shuttle. Jog shuttle Turn the jog shuttle to select a program or setting. Press the jog shuttle to confirm the selection.
Guide to the dryer Menu Program selection Program selection Back A Cottons Minimum iron Woollens handcare H ^ All pre-set programs can be selected with the jog shuttle. Depending on the direction the jog shuttle is turned the highlighter moves up or down. The arrows e- at the right side of the display show that more selections are available. ^ Press the jog shuttle to open the basic menu of the selected program. Basic menu of a drying program Cottons Normal Duration 1:16 h Low temp.
Before using for the first time The appliance must be correctly installed and connected before the first use. Please see the "Installation instructions." Welcome screen The Welcome screen shows when the dryer is turned on for the first time. Once the total use time of the dryer exceeds one hour the welcome screen will not show again. The display then shows the language selection. Language J Select the desired language and confirm with "OK".
Use Fabric care labels Before drying, check fabric care labels for special drying instructions. q = Drying with normal temperature r = Drying with low temperature s = Do not dry in a tumble dryer Drying tips – Observe the maximum loads, see the "Program guide". Overloading the dryer will result in poor drying and wrinkling. – Do not place dripping wet items in the dryer. Spin the laundry after the wash for at least 30 seconds.
Use 1. Sort the laundry 2. Load the laundry ^ Loosen up the washed laundry. ^ Use the a button to open the drum door. ^ For even drying results sort by desired dryness, fiber/fabric, size and residual moisture after spinning. ,Do not dry items that may melt or ignite in the dryer such as plastics, rubber or sneakers. They could melt and damage the laundry. ^ Load the laundry loosely into the drum. Do not overload the drum. Overloading strains the fabrics and results in poor drying.
Use 3. Select a program 6. Starting a program Two program selection possibilities: "Start" flashes when the program can be started. ^ Select a "Favorite" by pressing the respective direct select button. ^ Press the "Start" button. or The "Start" button lights. ^ Select from the "Program selection" menu by turning the jog shuttle. – The display shows "Program start" and then "Drying" with the program duration. 4. Select "Low temp." and/or "Timer" – The drying levels are displayed, e.g.
Use Remaining time 7. At the end of a program When a program is selected, the approximate duration is displayed. This is the "remaining time". "Anti-crease" (if selected) and "End" mark the end of a program in the display. During the anti-crease phase the drum will turn in intervals if the laundry is not immediately removed from the dryer to prevent the laundry from wrinkling. Run time 1 h.
Use Coin mechanism For coin mechanism operated machines: Money or tokens will be lost when the door is opened after program start or when canceling a program. Technical Service can set a time frame when a program can be changed. Adding/removing laundry during a drying program ^ Press the a button. ^ Open the door. ,Do not touch the rear of the drum while adding or removing items. Danger of burns due to high temperatures in the drum. Canceling a program ^ Add or remove items.
Program guide Programs may vary depending on the offerings of your machine. Cottons Extra dry, Normal+, Normal Items Load size: 14.3 lbs (6.5 kg) Single and multilayered cotton and linen laundry e.g. terry towels, beach towels, bath robes, T-Shirts, underwear, cottons bed linens, baby clothing, etc. – Select "Low temp." for items with the fabric care symbol r. – Select "Extra dry" for multilayered and thick items. – The "Extra dry" program should not be selected for jersey materials. Items may shrink.
Program guide Woollen handcare Items Note Load size: 5.5 lbs (2.5 kg) Woolen fabrics – Woolen items will be loosened up and fluffed in a short time, but not completely dried. – Remove the items immediately after the program ends and allow them to air dry. Smoothing Load size: 6.6 lbs (3.0 kg) Items – Cotton or linen fabrics – Permanent Press items of cotton, mixed fabrics or synthetics. e.g. khakis, shirts, etc. Note – Program to reduce creasing after spinning in the washer.
Program guide Load size: 7.7 lbs (3.5 kg) Jeans Normal, Hand iron r Items Denim fabric items, pants, jackets, skirts or shirts, etc. Shirts Normal, Hand iron r Items Shirts and dress shirts. Outerwear Normal, Hand iron r Items Load size: 5.5 lbs (2.5 kg) Load size: 7.7 lbs (3.5 kg) Outdoor clothing suitable to dry in a tumble dyer. Proofing Load size: 5.5 lbs (2.5 kg) Items For dryer suitable items, e.g. ski and outdoor clothing, tablecloths and poplin items.
Timer The timer allows the user to select the time of day for the program end. The program start can be delayed from 30 minutes to 24 hours. Select the submenu Timer Cottons Normal+ Low temp. Duration 1:47 h Low temp. B Timer Y Save Back A H H H H ^ Press the direct select button E. The "Timer" menu shows. Select the time Cottons Normal Low temp. 10:00 Start 10:13 Finish 12:00 ^ Select the desired program end time with the jog shuttle and confirm.
Favorites The dryer has the option to save the most used drying programs on the direct select buttons. The option "Save" must be selected in "Settings - Supervisor level". Contact Technical Service for access to this level. Selecting/Changing a Favorite ^ Close the door. Main menu 1 Cottons Program selection ... 2 Minimum iron Settings F ... 3 Woollens handcare 4 Smoothing 10:00 ^ Press the D button. Basic menu Cottons Normal Duration 1:16 h Low temp.
Favorites Depending on the selection the display shows one of the following submenus – Select a program Program selection Back A Cottons Minimum iron Woollens handcare H ^ Select the desired program with the jog shuttle and confirm. Important: If no selection is made in the submenu, the display will switch back to the basic menu after 20 seconds. – Drying level programs Cottons Normal+ Drying levels from Machine iron - Extra dry c ^ Select and confirm the desired drying level with the jog shuttle.
Favorites Low temp. To dry delicate items (fabric care symbol r) e.g. made from acrylic, press the "Low temp." button. – The temperature is reduced and the program duration is extended. ^ Press the D "Low temp." button. Saving a Favorite The basic menu shows all selected components. Cottons Normal+ Low temp. Duration 1:47 h Low temp. B H Timer Y H Save H Back A H ^ Press the F "Save" button. Assigning a direct select button Cottons Normal+ Low temp.
Cleaning and Care Cleaning the lint filter ,Check and clean the lint filter when the following message shows: "Clean the filters" or "Clean out airways". A two-piece lint filter in the dryer fan cavity collects the lint. It has to be removed and disassembled. Note: Use a vacuum cleaner to clean the lint filter without touching it. Removing the lint filter ^ Pull the lint filter out by its handle. Disassembling the lint filter ^ Press on the right side of the flap to open it.
Cleaning and Care Clean the lint filters - dry Cleaning the fan cavity Check the fan cavity regularly. Clean only if heavily soiled. ^ Open the door. ^ Remove the lint with your fingers or a vacuum. Clean the lint filters - wet Rinse the lint filters only if clogged. ^ Turn the knobs, a, of the left and right covers until they click. ^ Holding by the knobs, pull the covers up, b, and clean. ,Let the lint filters air dry before inserting them. The dryer efficiency can be affected by wet lint filters.
Cleaning and Care Cleaning the exterior and the control panel ,To reduce the risk of electric shock, disconnect the appliance from the power supply by unplugging or tripping the circuit breaker. ,Do not use an abrasive cleaner, glass cleaner or all-purpose cleaner. They will damage the dryer. The impeller in the dryer interior can become clogged with detergent residues or lint. ,Do not hose the dryer down.
Frequently asked questions Repairs to electrical appliances must only be carried out by a qualified and trained technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or machine damage. The manufacturer cannot be held responsible for unauthorized work. Check and fault messages in the display What if ... l Adjust the load , Technical fault A numerical fault message shows, e.g. "F47". 26 Possible cause Solution This is not a fault.
Frequently asked questions What if ... Possible cause At the end of a program Clean filter or The dryer reminds you to – Remove and clean the lint filter. clean the lint filter. To delete this message: – Confirm with "OK". The cycle of the "Clean – See "Settings - Supervisor level filter" message can be - Cleaning the lint filters". adjusted.
Frequently asked questions Other faults What if ... The program runs too long or stops. Possible fault Solution In some cases "Clean out airways" is displayed. See "Settings - Supervisor level - Clean the airways". Open and close the dryer door. The air supply is Open a window or door to insufficient. increase the air flow. The lint filter is clogged Remove the lint. with lint. The exhaust hose or the – Check the exhaust parts connection is clogged with regularly (e.g. wall vent duct, lint.
Frequently asked questions What if ... Possible fault What if there is The non-return flap of the condensed water in dryers' collective exhaust the drum? duct does not work correctly. Items made of synthetic fabrics have static cling after drying. Lint has built up. Solution – The dryer must only be installed with a non-return flap to a collective exhaust duct. – Check the non-return flap regularly for damages and replace if necessary. Synthetics are prone to static cling.
Frequently asked questions What if ... Possible cause Solution A program cannot be started, the display remains dark. The fault cannot be detected immediately. – Is the dryer connected to the power mains? – Is the door closed? – Are the fuses blown? After closing and opening the door the light comes back on. The drum light does The light turns off not come on. automatically (energy saving). The bulb may be bad or burnt out. The display shows a foreign language.
Frequently asked questions Changing the light bulb To reduce the risk of electric shock, disconnect the appliance from the power supply by unplugging or tripping the circuit breaker. ^ Open the door. The bulb cover is located along the upper rim of the drum opening. The light bulb must not exceed the maximum wattage listed on the data plate. ^ Replace the light bulb with a new one. ^ Flip the light bulb cover upwards and press it firmly into the left and right sides until it clicks into place.
After sales service In the event of a fault which you cannot fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Service Department, please quote the model and serial number of your appliance. They can be found on the data plate located below the drum opening. The PC indicator allows a service technician to check and update the drying programs.
INSTALLATION INSTRUCTIONS To prevent accidents and machine damage read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS , WARNING - Risk of Fire ~ To reduce the risk of severe injury or death, follow all installation instructions. ~ Clothes dryer installation must be performed by a qualified installer. ~ Install the clothes dryer according to the manufacturer's instructions and local codes. ~ Check the packaging, the dryer and accessories for any signs of damage. Do not use a damaged appliance. ~ Repair and maintenance work should be performed by a Miele authorized service technician.
IMPORTANT SAFETY INSTRUCTIONS ~ When installing multiple dryers to one collective exhaust duct, a non-return flap per dryer must be installed directly to the collective duct. Otherwise the dryers could be damaged and the electrical safety affected. ~ The installation of this unit in non stationary locations (e.g. ships) must be performed by a qualified installer or service agency, in strict accordance with national and local safety regulations and standards.
Installation Front view a Exhaust connection d Door The exhaust hose can be installed either at the rear, left or right of the dryer.
Installation Side view Top view Rear view Washer/ Dryer Stack a Lid over hang with transport grips (arrow) The Miele dryer can be installed as part of a washer-dryer stack in combination with a Miele washer. An appropriate "stacking kit" available from Miele is required. Installation of the stacking kit must be completed by a Miele Service Technician.
Installation Installation on a cement base Coin mechanism The dryer can be equipped with a coin mechanism (optional accessory). Miele’s Technical Service will install the coin mechanism and program the electronic. Empty the coin mechanism regularly to avoid jams. ^ Secure the front feet of the dryer with retaining clips on the cement base. ,Do not install devices to automatically turn the dryer off, e.g. clock timers.
Installation Installation ,Do not install a lockable or slide door in the pivoting area of the dryer door. Transporting the dryer to the installation site The rear overhang of the lid has transport grips. ^ Use the front dryer feet and the rear overhang to transport the dryer from the packaging base to the installation site. Level the dryer ^ The machine can be leveled by turning the legs clockwise or counterclockwise as necessary.
Installation Electrical connection ,This installation should be performed by an experienced and qualified technician, in accordance with local codes and regulations. The dryer comes with a power cord and NEMA L6-30 plug. The machines is supplied for a connection to a 2 AC 208V 60Hz 2x30A, Single Phase Supply. For extra safety it is advisable to install a residual current device (RCD) with a trip current of 30 mA. The machine must only be connected to the voltage and frequency shown on the data plate.
Installation of exhaust venting General notes ,The dryer must only run if the moist exhaust air from the drying process is conducted outside by an installed exhaust duct vent. ,Disconnect the dryer from the power supply during installation of the exhaust duct. The exhaust connection (e.g. a wall pipe) must be installed, so that the moist exhaust air cannot get drawn back into the installation room and cause constructional damage or unreasonable disturbance.
Installation of exhaust venting How to calculate the effective duct length The overall duct length will determine the duct diameter (see the "Additional duct lengths" table). In Canada the exhaust duct must be 4" (102 mm) in diameter. ^ Measure the actual duct length needed to go from the dryers exhaust connection to the vent outlet: 1. Establish the number of elbows or bends necessary, noting the type of bend, angle and radius involved (see Table). 2.
Installation of exhaust venting Tips about the ductwork – Check with your local building codes to determine the maximum allowable duct length. – Only use rigid or flexible metal duct for exhausting. Non-metallic flexible hose should not be used, it is a potential fire hazard. – In the United Stated foil-type flexible ducts should only be used if identified for use by the manufacturer as compliant with the Outline for Clothes Dryer Transition Duct, Subject ANSI/UL 2158A.
Installation of exhaust venting Additional duct lengths (4" rigid pipe only) Type of bend Radius Additional duct length ft cm ft cm Flexible metal duct – 3’ 3" (1 m) straight – 45° angle – 90° angle 10" 10" 25 25 5’ 11" 4’ 11" 8’ 2" 180 150 250 Smooth metal duct – 3’ 3" (1 m) straight – 45° angle – 90° angle 10" 10" 25 25 3’ 3" 1’ 11" 2’ 7" 100 60 80 7’ 6" 230 2’ 4" 70 Wall vent or window vent – with louvers – with flap 12’ 5" 4’ 11" 380 150 Exhaust connection – left or right side 3
Installation of exhaust venting Example: Calculating the effective duct length and required internal duct diameter Rigid pipe Duct length ft Duct length m A Wall duct with louvered wall vent 12’ 5" 3.8 m B 90° bend 2’ 7" 0.8 m C 20" (0.5 m) rigid pipe 1’ 7" 0.5 m D 90° bend 2’ 7" 0.8 m E left vent opening 3’ 3" 1.0 m 22’ 5" 6.9 m Total duct length The total duct length is less than 33 feet (10 m), so a duct diameter of 4" (100 mm) with adapter is sufficient.
Installation of exhaust venting Determining the position of the exhaust connection The exhaust connection can be left at the rear of the dryer (factory standard) or moved to the left or right side of the dryer. Changing the position of the exhaust connection ^ Remove the cap by turning it counterclockwise. ^ Press the supplied cover firmly into the rear opening. Install the exhaust duct as follows.
Installation of exhaust venting Exhaust connection with a flexible exhaust hose or rigid pipe Window connection Using the connector supplied, an exhaust hose (4" [100 mm] diameter) can be installed. Necessary materials: – the supplied connector – a wall or window duct (optional accessory) – an exhaust hose made of approved non-flammable material.
Installation of exhaust venting Chimney connection 1 Pipe with connection nozzle (= single parts of the Miele wall pipe) 2 Connector for the flexible exhaust hose 3 Chimney, humidity insulated ,The appliance must not be connected to a chimney or vent flue which is in use. Neither should it be connected to ducting which ventilates rooms with fireplaces.
Installation of exhaust venting Direct wall connection Dryer side view This venting type is ideal if the dryer can be installed directly to an outer wall. The shorter the exhaust ductwork, the more efficient the dryer will be. However, for the wall pipe to be installed a hole must be cut through the outer wall. Regard the Install manual for the Miele wall pipe and the dimension illustrations below.
Installation of exhaust venting Collective exhaust duct ,A non-return flap* (optional accessory, see right picture) per dryer must be installed directly into the collective exhaust duct. Otherwise the dryers can be damaged and the electrical safety compromised. When installing multiple dryers, increase the duct diameter. Number of units Increasing factor for duct diameter from table 2 2 3 4 - max. 5 1 1.25 1.
Technical Data Height 33 7/16" (850 mm) (adjustable + / - 1/4" (7 mm)) Width 23 7/16" (595 mm) Depth Depth with the door open 27 9/16" (700 mm) 46 3/4" (1,188 mm) Weight Drum 123 lbs (56 kg) 28.6 gal (130 l) Maximal load Power cord 14.3 lbs (6.5 kg) Dry laundry weight 63" (1.6 m) Fuse rating Rated load see data plate see data plate Fuse rating Light load see data plate see data plate Maximum floor pressure during operation approx.
Caring for the environment Disposal of the packing materials The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. To prevent suffocation, ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. 52 Disposal of an appliance Old appliances may contain materials that can be recycled.
Menu Settings J to adjust standard settings The dryer controls can be adjusted to changing demands through the settings. Depending on default settings: – some settings are visible and can be changed by all users (Menu "Settings J") or – all setting are locked in the "Supervisor level" by a code (Menu "Settings - Supervisor level"). Contact Miele Technical Service.
Settings J Opening the menu Settings 1 Cottons Program selection ... 2 Minimum iron Settings F ... 3 Woollens handcare 4 Smoothing 10:00 ^ Select "Settings" J in the main menu and confirm by pressing the jog shuttle. Selecting Settings Settings Back A Language F ... Anti-crease Buzzer H ^ Select the setting to be changed and confirm. If no selection is made in the submenu, the display will switch back to the "Settings" menu after 20 seconds.
Settings J Language J The displayed language can be set in the submenu "Language J". The flag behind the word "Language J" is a guide to find the settings menu in case a foreign language is selected. ^ Select the desired language and confirm. The change is only valid for the current program. At the end of the program the display language will change back to the language set in the "Settings Supervisor level".
Settings J Contrast/Brightness Display contrast and brightness can be adjusted in 10 levels. Lengthening the cooling time The cooling phase can be lengthened before the program is started. The laundry will be cooled. The bar shows the selected level. The bar shows the selected level. Standby The display goes into standby mode after 10 minutes and the "Start" button flashes slowly to save energy. on Standby is turned on: – when no program is selected. – after pressing the "Start" button.
Settings - Supervisor level The menu "Settings - Supervisor level" is locked with a code to prevent unauthorized access (except Language J). It must be activated by Technical Service. Settings Back A Supervisor level Access via code ^ Select "Access via code" and confirm. Entering the code ^ Enter the code "0 0 0" (factory default). If a wrong code is entered three times, the code entry will be locked for 1 hour. 0 _ _ Please enter code ^ Turn the jog shuttle until the first digit shows.
Settings - Supervisor level Language J The display contents can be shown in different languages. The fixed default language can be set in the submenu "Language J". Controls The controls can be set to "Household" (default setting) or laundromat version "WS-KW buttons simple". ^ Select the desired language and confirm with "OK".
Settings - Supervisor level Language entry A selection can be set to show an additional welcome menu with language selection before the entry menu and at the end of the program. national: no additional welcome menu international: The welcome menu shows. A language must be selected. All languages are available. See "Sort languages". Drying levels The bars show the selected level. Factory default: medium level – The program duration shortens (more moist) or lengthens (more dry).
Settings - Supervisor level Cleaning the airways The lint filters must be cleaned after every drying cycle. Additionally the indicator "Clean out airways" lights once a certain level of lint is collected. The user can decide at which level of lint collection the indicator should come on. off "Clean out airways" does not light up heavy "Clean out airways" shows only when large amount of lint is collected. normal Factory default light "Clean out airways" shows even when a small amount of lint is collected.
All rights reserved / 1912 M.-Nr. 06 975 240 / 04 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
