Operating instructions Fashion Master (steam ironing system) B 1312 B 1826 B 1847 To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed, set up and used for the first time. en - GB M.-Nr.
Contents Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Caring for our environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Disposal of your old appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Moving the Fashion Master. . . . . . . . . . . . . . . . .
Contents Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Cleaning the casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Automatic rinse . . .
Guide to the appliance a Ironing table i X-frame for the ironing table b Iron with steam hose j Iron resting surface c Steam hose holder k Mains connection cable d Handle f Tower l Lower storage compartment for the mains connection cable, steamer*, non-stick sole plate and holder for the mains connection cable.
Guide to the appliance h On/Off button s with indicator light i Steam ready * indicator light j Water container empty k indicator light k Steam generator too hot l indicator light a Handle with rotary dial for adjustment and folding the appliance up b Iron resting surface c Steam connection l Empty residual water container 2 indicator light m Descale k indicator light n Descale button j d Sockets for the steam hose holder e Control panel f Steam hose holder g Iron with steam hose 5
Warning and Safety instructions This appliance complies with all relevant safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important information about its safety, use and maintenance. Keep these instructions in a safe place and ensure that new users are familiar with the content.
Warning and Safety instructions Safety with children ~ Children 14 years and older may only use the appliance if they have been shown how to use it in a safe way and understand the hazards involved. ~ Children under 14 years of age must be kept away from the appliance unless they are constantly supervised. ~ The appliance is not a toy! To prevent the risk of injury, do not allow children to play with it or use the controls. Please supervise children whilst you are using the appliance.
Warning and Safety instructions ~ Do not use the appliance if the ironing table cover is damaged. A damaged ironing table cover could be dangerous. Do not use the appliance without an ironing table cover. The ironing table cover must be replaced with an original Miele cover. ~ The electrical safety of this appliance can only be guaranteed when correctly earthed.
Warning and Safety instructions ~ The appliance must not be used in a non-stationary location (e.g. on a ship). ~ In areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee. Correct use , Caution. Danger of burning.
Warning and Safety instructions ~ Do not use demineralised water (e.g. distilled) on its own to fill the water container as this could cause the appliance to malfunction. ~ Always place the iron with the steam function switched off on the iron resting surface so that the sole plate does not protrude over the edges. Placing it otherwise could be a fire hazard. ~ Take care not to burn yourself. If the iron remains on the resting surface for any length of time, the surface will become hot.
Warning and Safety instructions ~ Do not plug any objects into any of the apertures on the steam ironing system. If an aperture is blocked, do not use the system. ~ Do not hang items of laundry on the appliance when folded as this could cause it to tip over. ~ Do not store the appliance near petrol, benzine or other easily flammable substances. Fire and explosion risk. ~ Only use the appliance in buildings with an ambient temperature of between 10°C and 40°C.
Caring for our environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags etc. are kept out of the reach of babies and young children.
Moving the Fashion Master The appliance is fitted with two rollers, so it can be pulled or pushed across an even surface when folded up. ^ Hold on to it by the handle and tip it gently towards you until the wheels are free. Two people are required to carry the Fashion Master up or downstairs. It should always be carried with the ironing table underneath. Obstacles such as carpet edges, door sills or single steps can also be easily negotiated. ^ Use the hand holds on the underside of the appliance.
Assembling ^ Take the Fashion Master to the place where it is to be set up. The ironing table is held independently in this position. ^ Pull upwards on the release mechanism with one hand. Hold the tower tightly by the handle with the other hand. ^ Pull the ironing table upwards with both hands into a horizontal position until you hear a click. The locking mechanism on the tower will be released and the X-frame will fold down at the same time.
Assembling The Fashion Master is now assembled in its lowest working position - a height of approx. 83 cm.
Assembling Adjusting the height You can adjust the Fashion Master to suit your working height. Take care not to trap the electrical connection cable in the mechanism. Ensure that the ironing table has clicked into place on both sides of the tower otherwise you will not be able to adjust the height. ^ At the same time pull the handle on the tower upwards with the other hand. or: ^ Press the handle on the tower down at the same time. Do not push down on the ironing table when doing this.
Connection The Fashion Master system is supplied for connection to a 230 volt, 50 Hz mains electricity supply and is fitted with a moulded BS 1363 plug. ^ Open the lower storage compartment by opening the lid downwards. ^ Remove the electrical connection cable completely from the compartment. ^ Insert the plug in a wall socket. ^ Guide the electrical connection cable through the grove provided and close the lower storage compartment again.
Connection ^ Close the storage compartment lid again. ^ Connect the iron by plugging the steam hose into the steam connection. Pull back the sliding mechanism on the steam hose plug and release it when it is plugged in. ^ Plug the steam hose holder into one of the sockets provided. Please note: Use the socket on the side on which you are ironing. The appliance can be used by right- or left-handed people. Operation is optimised for both sides. ^ Open the lid of the steam connection by lifting it upwards.
Connection ^ To avoid damaging or fading the ironing table cover, always place the iron on the resting surface during pauses in ironing. Condensation can form on the resting surface. However, this does not affect the functioning of the steam ironing system. When putting the iron down on the iron resting surface, the steam * button must be unlocked. ,The iron must not be placed upright on the resting surface as it could tip and fall.
Before using for the first time It is helpful to get to know the FashionMaster before using it for the first time so that you will be able to make use of all the functions. ^ Remove the packaging (e.g. the protective film from the tower, etc). When using for the first time, you might notice a slight odour during the heating-up phase. This will dissipate with further use. During operation pumping, boiling and knocking noises may be heard. These are normal noises which occur during operation.
Before using for the first time If you cannot find out the water hardness level, you can use the test strip provided: If your water hardness is different from this, you must adjust it to the corresponding value. Where the water hardness fluctuates e.g. between 6.7 - 9.0 mmol/l (37 - 50 °dH), always programme it to the higher value (9.0 mmol/l / 50 °dH in this example). In the event of a fault, it will help the service technician if you know the hardness of your local water supply.
Before using for the first time Setting the water hardness level Water hardness is programmed using the control panel on the tower. ^ Briefly press the j button to select the number of flashes which equates to your water hardness level. Each press of the button moves you up a level. When the highest water hardness value is reached, the setting starts from the beginning again. Please set the correct water hardness level, as otherwise this invalidates the guarantee.
Switching on Switching on the Fashion Master Filling the water container If the water container is empty or not inserted into the system, the k indicator light comes on. ^ Press the On/Off button s. The ring around the s button lights up yellow. The Fashion Master starts heating up. Steam can escape from the iron during the heating-up phase. During operation pumping, boiling and knocking noises may be heard. These are normal noises which occur during operation.
Switching on If you refill and replace the water container as soon as the indicator light k lights up, there is no delay. The * indicator light indicates readiness immediately. While the k indicator light is on, the steam system is not active. The iron remains functional. Energy-saving tip: You can save energy by ironing without steam by removing the water container, so that the steam generator is not heated. ^ Turn the screw cap on the back of the water container anti-clockwise and lift it off.
Switching on Water quality CoolDown function Use only fresh tap water. If the iron is not moved for more than 3 minutes, the heating switches off. After some time steam is no longer available and the * indicator light goes out. The iron will automatically start heating up again as soon as the iron is moved. The time taken for steam to be available again depends on the length of time the heating was switched off. Filtered tap water may also be used. For water hardness of more than 2.
Switching on Selecting the temperature for ironing Material Minimum iron/ Synthetics Woollens/ Silks Linen / Cottons Dot symbol ß ßß ßßß Temperature range Low temperature Medium temperature High temperature ^ Use the temperature selector to set the temperature required. The temperature selector on the iron is used for setting the ironing temperature. The temperature settings are indicated by dots around the selector. These dots correspond to the international symbols for ironing.
Switching on Tip: Sorting the laundry Sort your laundry according to heat sensitivity for efficient ironing. Iron the most sensitive fabrics, such as synthetics first, Then iron silk, wool, cotton and linen at increasing temperatures. Please also observe the advice and symbols on the care labels in your garments.
Ironing Iron B 1826 and B 1847: Your Fashion Master has one of the following irons, depending on model: B 1312: a Steam button * b Sliding switch for constant steam a Steam button * b Sliding switch for constant steam c Suction button p d Blow button o 28 c Power output selection button m d Blow/suction button n
Ironing Ironing with steam The burst of steam is controlled by the * button. The fan starts up when the * button is pressed. The fan will continue running for a short while after using steam. For short bursts of steam: ^ Press the * button briefly and release it again. For constant steam: ^ Press the * button and at the same time slide switch b backwards. Condensate can form in the steam hose during pauses in ironing. This is expelled by operating the steam button.
Ironing Ironing with the non-stick sole plate In the lower compartment there is a non-stick sole plate which simply clips onto the iron. ,Danger of burning. The sole plate becomes very hot when in use. Avoid direct contact with it. It also reduces or eliminates the formation of shiny patches on dark textiles. Always try it out on an unobtrusive part of the fabric first. Removing the non-stick sole plate ,Danger of burning. The sole plate becomes very hot when in use. Avoid direct contact with it.
Ironing Fan Suction function The fan on the ironing table is controlled with the o, p or n, m buttons. The suction function assists steam permeation of textiles, avoids the formation of condensation on the ironing table and holds the item so that it does not slip off the ironing table. B 1312 only: The blow function is activated by the o button. The suction function is activated by the p button.
Steamer Steamer (B 1847 only) The B 1847 Fashion Master is equipped with a steamer in addition to the iron. The steamer can be plugged into the steam connection as an alternative to the iron. ^ Remove the steamer from the lower compartment. ^ Disconnect the iron from the steam connection in the tower. Pull back the sliding mechanism on the steam hose plug and withdraw the plug. Do not pull on the steam hose. ^ Plug the steam hose of the steamer into the steam connection.
Steamer a ,Danger of burning. Do not direct the steam or the steam jets at people, animals or electrical appliances of any kind. The distance between the steamer and the textile is dependent on the sensitivity of the fabric and can vary between textiles. Always test this first on an unobtrusive part of the fabric. Condensate can form in the steam hose during pauses in ironing. This is expelled by operating the steam button.
Steamer Brush attachment The steamer comes with a brush attachment which can be clipped onto the head. The steamer can be held directly on the textile with the brush attached. Always try it out on an unobtrusive part of the fabric first. The brush attachment helps to raise and straighten the fibres. ^ Guide the brush attachment into the notches on the opposite side and click these into place.
Switching off Switch off the appliance. ^ Press the On/Off button s. The yellow ring around the s button goes out. The last fan settings selected are saved for the next time you switch on. If you are putting the appliance away: ^ Disconnect the appliance from the mains electricity supply. ^ Stow the electrical connection cable in the lower compartment or hang it up on the cable clip. The cable clip is in the lower compartment and can be pushed into one of the sockets for the steam hose holder.
Storage ^ Place the iron on the resting surface to cool down. Once the iron has cooled down you can fold the Fashion Master away. The ironing table must be put back in the lowest working position in order to fold the appliance away. Ensure that the residual water container is correctly inserted and clicked into place and take care not to trap the electrical connection cable in the mechanism. ^ At the same time push the tower handle downwards to lower the ironing table into the lowest working position.
Storage Make sure that the ironing table is in its lowest working position when releasing it. There must also be nothing on the ironing table. ^ Guide the ironing table downwards or allow it to slide down by itself. The ironing table is held independently in this position. ^ Turn one of the rotary dials as far as it will go towards ). The ironing table is now released. ^ Release the rotary dial and it will spring back into the middle position.
Storage ^ Once the iron has cooled down on the resting surface, stow the iron and the steam hose holder in the upper storage compartment ^ Stow the steamer (for B 1847) in the lower storage compartment. Do not stow the iron or steamer if they are still connected. Empty the water container if the system is not going to be used for a long period. ^ Push the bottom of the X-frame which is still protruding in until it clicks into position. ^ The Fashion Master can now be put away.
Cleaning and care Cleaning the casing ,Disconnect the appliance from the electricity supply before any cleaning and maintenance work on the casing. The 2 indicator light comes on. Emptying the residual water container The residual water container may be hot after rinsing. Do not use any abrasive cleaning agents. Depending on the level of soiling, the casing can be wiped with a wet or dry E-cloth (see "Optional accessories").
Cleaning and care Automatic descaling Make sure that the metal contact discs at the top of the residual water container are cleaned and dried properly. These metal discs send a signal to the appliance when the residual water container is full or if it is not in the appliance. The discs will not convey these signals if they are dirty or damp. ^ Insert the residual water container after a short interval (approx. 15 seconds) so that it clicks into place. The 2 indicator light goes out.
Cleaning and care Descaling can be started at any time whilst the red k indicator light is flashing by pressing the j button. If the k indicator light is permanently on, the remaining operating hours have expired. You can still finish your ironing, however, the appliance must carry out descaling next time it is switched on, before any more ironing is done. ^ Disconnect the steam hose of the iron or the steamer from the steam connection.
Cleaning and care If the appliance is still hot from the last use, the l indicator light comes on. The descaling process is automatically resumed when the appliance has cooled down and the l indicator light has gone out. The k and 2 indicator lights go out. The k indicator light comes on. Water is now pumped into the steam generator to rinse it out. The water is then drained away completely into the residual water container. The 2 indicator light comes on again.
Cleaning and care Cleaning the ironing table cover Replacing the ironing table cover If the ironing table cover is soiled, it can be removed for washing. Do not use the appliance if the ironing table cover is damaged. ,Do not operate the appliance without an ironing table cover. ,When removing the ironing table cover, always ensure the appliance is switched off and disconnected from the electricity supply. Wait until the ironing table has cooled down.
Cleaning and care Cleaning the sole plate of the iron ,Caution. Danger of burning. The sole plate of the iron remains hot for some time after ironing. Allow it to cool down before starting to clean it. ^ Switch the appliance off and disconnect it from the electricity supply before cleaning the iron sole plate. Depending on the level of soiling, the sole plate can be wiped with a wet or dry E-cloth (see "Optional accessories").
Cleaning and care Cleaning the water filter The water filter prevents foreign objects in the water from getting into the appliance and causing damage. If the water filter is dirty or blocked, it can be cleaned. A dirty water filter can cause more frequent pumping noises from the water feed pump. ^ Switch the appliance off and disconnect it from the electricity supply before cleaning the water filter. ^ Undo the screw on the water filter cover and lift the cover upwards and off.
Cleaning and care ^ Replace the water filter, ensuring that the filter seal is underneath. ^ Replace the seal in the right-hand socket. ^ Attach the appropriate tool in the cover onto the water filter in the right-hand socket and remove it. ^ Replace the cover and tighten the screw. ^ Replace the water container. The appliance is ready for use again. Do not use the appliance if the water filter is not in place as this will cause a fault to be indicated. See "Problem solving guide".
Optional accessories Miele appliances are built to the highest standards to achieve the best possible results for as long as possible. To help you get the most out of your appliance Miele also offers a comprehensive range of accessories and care products. The following products are just a few examples from our full range which is available to order online at: Ironing table cover Miele ironing table covers are hard-wearing and highly absorbant.
Optional accessories Cleaning products The Miele CareCollection has products which have been specially developed to clean your appliance gently and thoroughly. Descaling tablets for the Fashion Master Miele descaling tablets guarantee an optimum result when descaling your Miele Fashion Master. One tablet is required for each descaling process. E-cloth (microfibre cloth) Removes fingerprints and light soiling without damaging the surface.
Problem solving guide With the help of the following notes, minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Service Department. ,Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous.
Problem solving guide Problem The appliance will not fold away. The ironing table will not click into place during assembly or dismantling for storage. Possible cause Remedy The ironing table is not in its lowest working position. Adjust the ironing table to its lowest working position (see "Storage") The residual water container is not correctly inserted and clicked into place. Insert the residual water container fully into the tower until it clicks into place.
Problem solving guide Problem Possible cause Remedy Water is leaking from the steam ironing system at the height of the water container when it is being transported. Water droplets can Dry the area underneath the collect in the area water container in the tower with under the water a cloth. container as a result of frequent removal and replacement of the water container. The iron or steamer does not heat up. The appliance is switched off. Switch the appliance on with the On/Off button s.
Problem solving guide Problem Possible cause Remedy The ironing table is not Steam has not been Operate the steam button *, to heating. used for a while. activate the ironing table heating. The iron always heats to a high temperature. The steamer is connected to the tower. The ironing table does not heat up when the steamer is connected. The appliance is damaged. Call Miele Service There is a fault with the appliance. Call Miele Service. The ironing table cover There is a fault with is damp.
Problem solving guide Problem Possible cause The fan is not running. No steam is required. The steam is not ready. Remedy The fan only runs when the steam function on the iron is operated. Wait until the * indicator light signals that steam is ready. The water container Fill the water container with fresh is empty or missing. tap water and insert it into the appliance. Descaling cannot be started, although the indicator light k is flashing or lit up. The steamer is connected.
Problem solving guide Problem Possible cause The appliance The iron or the switches off during the steamer was descaling process. connected during the descaling process. Remedy Disconnect the iron or the steamer from the steam connection. Switch the appliance on again. The k indicator light is The water container Remove the water container, fill on. or contents have not and replace it. been recognised. Rinsing or descaling could still be taking place. Wait until the process has finished.
Problem solving guide Problem The 2 indicator light is on constantly. Possible cause Remedy The empty residual Empty the residual water water container has container completely and dry it not been recognised. out. Insert the residual water container after a short interval (approx. 15 seconds) so that it clicks into place. Clean and dry the metal contacts on the residual water container and replace the container. If the indicator light is still on, call Miele Service.
Problem solving guide Problem When using the steam button * on the iron, drops of water or white deposits escape from the steam jets. Possible cause Remedy The temperature Set the temperature to at least selected on the iron ßß (see "Selecting the temperature for ironing"). is too low. The appliance is not ready to steam and the iron has not yet reached the selected temperature.
Problem solving guide Problem The * indicator light flashes four times and the k indicator light is also lit up. Possible cause Remedy The empty or missing water container is not recognised by the appliance. Switch off the appliance. Fill the water container with fresh tap water and replace it. Do not use distilled water. Switch the appliance back on again. The water container The l indicator light is lit up.
Problem solving guide Problem The * indicator light flashes six times and the k indicator light is also lit up. Possible cause Remedy The steam generator is contaminated with water which is too hard or too salty. Start the descaling process by pressing the j button. In this case the descaling requirement is not indicated by the k light (see "Cleaning and care").
Problem solving guide Problem The * indicator light flashes eight times and the k indicator light is also lit up. Possible cause The residual water container has not been recognised. Remedy – Switch off the appliance. – Wash and dry the metal contacts on the residual water container. – Switch the appliance on again and reset it as follows: – Insert the residual water container, filled with water, for at least 15 seconds. – Remove the residual water container again and empty it.
After sales service In the event of a fault that you cannot easily remedy, please contact – your Miele Dealer or – Miele (see back cover for contact details). Please note that telephone calls may be monitored and recorded for training purposes (UK only). When contacting Miele, please quote the Model and Serial number of your appliance, both of which are given on the data plate which is located in the tower behind the water container.
Electrical connection ,All electrical work must be carried out by a suitably qualified and competent person in accordance with current local and national safety regulations (BS 7671 in the UK). This appliance is supplied with a connection cable and moulded plug (BS 1363) for connection to a 230 V mains supply. The appliance must only be operated with the voltage, frequency and fuse rating shown on the data plate (located in the tower behind the water container).
Technical data Dimensions when dismantled (H x W x D) 1281 x 471 x 382mm Dimensions when assembled (H x W x D) 963 x 1460 x 471mm Weight 29 kg for B 1312 and B 1826 30 kg for B 1847 Voltage See data plate Connected load See data plate Fuse rating ³ 10A Steam pressure 3.5 bar for B 1312 4.0 bar for B 1826 and B 1847 Steam output 100 g/min Capacity of water container 1.25 l Electrical connection cable length 2.50 m Steam hose length 1.
Alteration rights reserved/1412 M.-Nr.