Operating instructions/Installation instructions
Table Of Contents
- Title page
- Contents
- Contents
- IMPORTANT SAFETY INSTRUCTIONS
- Appliance description
- Caring for the environment
- References to illustrations
- Preparing for use
- Attaching the suction hose (Fig. 01)
- Disconnecting the suction hose (Fig. 02)
- Connecting the suction hose to the handle (Fig. 03)
- Connecting the handle to the wand (Fig. 04)
- Adjusting the telescopic wand (Fig. 05)
- Connecting the telescopic wand to the floorhead/floorbrush (Fig. 06)
- Adjusting the floorhead (Fig. 07 + 08)
- Using the accessories supplied (Fig. 09)
- Use
- Parking, transport and storage
- Maintenance
- _
- Emptying the dust container (Fig. 21 - 26)
- Cleaning the dust container
- Cleaning the filter frame (Fig. 27 + 28)
- Cleaning the fine dust filter
- Starting the ComfortClean self-cleaning function manually (Fig. 29)
- When to change the thread catchers?
- How to replace the thread lifters (Fig. 30 + 31)
- Cleaning the roller on the AllTeQ floorhead (Fig. 32)
- Cleaning and care
- Frequently Asked Questions
- Frequently asked questions
- Technical Service
- Optional accessories
- Purchasing accessories
- Floor tools / Brushes
- AllergoTeQ floorhead (SBDH 285-3)
- TurboTeQ Turbobrush (STB 305-3)
- Parquet Twister floorbrush with swiveling head (SBB 300-3)
- Floorbrush Parquet Twister XL with swiveling head (SBB 400-3)
- Other accessories
- MicroSet accessory case (SMC 20)
- Turbo XS hand turbo brush (STB 20)
- Universal brush (SUB 20)
- Radiator brush (SHB 30)
- Mattress tool (SMD 10)
- Crevice nozzle, 12" (300 mm) (SFD 10)
- Crevice nozzle, 22" (560 mm) (SFD 20)
- Upholstery nozzle, 7 1/2" (190 mm) (SPD 10)
- Contents
- Leere Seite
- Leere Seite
- Leere Seite
en-US
15
Use
Power cord
Unwind the cord completely to
aid the vacuum in dissipating heat.
Do not pull or carry by the cord, use
the cord as a handle, close a door on
the cord, or pull the cord around
sharp edges or corners. Do not run
the appliance over the cord. Keep
the cord away from heated surfaces.
Do not unplug by pulling the cord. To
unplug grasp the plug, not the cord.
This appliance is equipped with a
power cord reel. Hold the plug when
rewinding onto cord reel. Do not al-
low plug to whip when rewinding.
Unwinding the cord (Fig. 12)
Pull the cord out to the required
length.
Insert the plug into the outlet.
If vacuuming for longer than
30minutes, the cord must be pulled
out all the way. Danger of overheat-
ing and damage.
Rewinding the power cord (Fig. 13)
Unplug the power cord from the
socket.
Step on the cord rewind foot switch.
The power cord will then retract itself
into the vacuum cleaner.
If you do not want the cord to retract
completely into the vacuum cleaner
you can deactivate this function. To do
this, take hold of the end of the cord
while rewinding it and give it a short
pull when you want the rewinding to
end.
Turning the vacuum cleaner on and
off (Fig. 14)
Press the On/Off foot control .
Selecting the suction power
The suction power can be adjusted to
suit the type of flooring being cleaned.
Reducing the power lowers the amount
of effort required to maneuver the floor
brush.
The vacuum cleaner has symbols on
the controls which indicate the type of
use the settings are suitable for.
Curtains, lightweight fabric
Deep pile carpets, rugs and run-
ners
Low pile carpet and rugs
Hard flooring and heavily soiled
carpets and rugs (also for clean-
ing upholstery and mattresses
with the upholstery nozzle)
Rotary dial (Fig. 15)
Turn the rotary selector to the suction
power setting you require.
Opening the air inlet valve (Fig. 16)
(not on models with the Eco Comfort
handle)