Operating instructions/Installation instructions
Table Of Contents
- Title page
- Contents
- Contents
- IMPORTANT SAFETY INSTRUCTIONS
- Appliance description
- Caring for the environment
- References to illustrations
- Preparing for use
- Attaching the suction hose (Fig. 01)
- Disconnecting the suction hose (Fig. 02)
- Connecting the suction hose to the handle (Fig. 03)
- Connecting the handle to the wand (Fig. 04)
- Adjusting the telescopic wand (Fig. 05)
- Connecting the telescopic wand to the floorhead/floorbrush (Fig. 06)
- Adjusting the floorhead (Fig. 07 + 08)
- Using the accessories supplied (Fig. 09)
- Use
- Parking, transport and storage
- Maintenance
- _
- Emptying the dust container (Fig. 21 - 26)
- Cleaning the dust container
- Cleaning the filter frame (Fig. 27 + 28)
- Cleaning the fine dust filter
- Starting the ComfortClean self-cleaning function manually (Fig. 29)
- When to change the thread catchers?
- How to replace the thread lifters (Fig. 30 + 31)
- Cleaning the roller on the AllTeQ floorhead (Fig. 32)
- Cleaning and care
- Frequently Asked Questions
- Frequently asked questions
- Technical Service
- Optional accessories
- Purchasing accessories
- Floor tools / Brushes
- AllergoTeQ floorhead (SBDH 285-3)
- TurboTeQ Turbobrush (STB 305-3)
- Parquet Twister floorbrush with swiveling head (SBB 300-3)
- Floorbrush Parquet Twister XL with swiveling head (SBB 400-3)
- Other accessories
- MicroSet accessory case (SMC 20)
- Turbo XS hand turbo brush (STB 20)
- Universal brush (SUB 20)
- Radiator brush (SHB 30)
- Mattress tool (SMD 10)
- Crevice nozzle, 12" (300 mm) (SFD 10)
- Crevice nozzle, 22" (560 mm) (SFD 20)
- Upholstery nozzle, 7 1/2" (190 mm) (SPD 10)
- Contents
- Leere Seite
- Leere Seite
- Leere Seite
en-US
20
Frequently asked questions
Always switch off the vacuum
cleaner before attempting to rectify a
fault and unplug it.
Cleaning the pre-filter(Fig. 31 + 32)
The pre-filter is located at the rear of the
vacuum cleaner.
This should be cleaned if it is obviously
dirty.
Remove the dust container.
Release the handle of the pre-filter
and remove the pre-filter.
Rinse the pre-filter under cold running
water.
Do not use detergent!
Do not use any sharp or pointed ob-
jects!
Dry the pre-filter carefully!
Replace the dry filter in the dust con-
tainer and lock the handle.
Reinsert the dust container in the
vacuum cleaner.
Cleaning the fine dust filter
manually(Fig. 33 -
38)
Allow a drying time of 24hours.
Remove the dust container.
Release the fine dust container in the
direction of the arrow and remove it.
Run a little water into the opening at
the top of the fine dust container.
Gently shake the fine dust container
back and forth.
This will rinse out the dust.
Shake the water out of the opening.
Release the top so that the marking is
pointing to the symbol.
Carefully lift the fine dust filter up and
out of the fine dust container.
Clean the outside of the fine dust fil-
ter under cold running water.
Do not clean the inside of the
fine dust filter.
Do not use detergent.
Do not use any sharp or pointed ob-
jects and do not brush the fine dust
filter.
After cleaning, allow the fine dust fil-
ter to dry for a minimum of 24hours.
Clean the fine dust container with wa-
ter and mild detergent.
Dry the fine dust container carefully.
Insert the dry fine dust filter into the
dry fine dust container so that the
marking is pointing to the symbol.
Lock the top into place so that the
marking is pointing to the symbol.
Reinsert the fine dust container in the
vacuum cleaner and lock it into place.
Reinsert the dust container in the
vacuum cleaner.
Customer Service
Contact in case of fault
In the event of a fault which you cannot
remedy yourself, please contact your
Miele dealer or Miele Service.