Operating and Installation Instructions Tepan Yaki CS 1327 To prevent accidents and appliance damage, read these instructions before installation or use. en - US M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Guide to the Tepan Yaki . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Turning On/Off . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS Correct usage WARNING- When using your appliance follow basic precautions, including the following: Read all instructions before installation or use to prevent injury and appliance damage. This appliance complies with current safety requirements. Improper use of the appliance can lead to personal injury and material damage. Keep these instructions in a safe place and pass them on to any future user.
IMPORTANT SAFETY INSTRUCTIONS Technical Safety ~ Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ Be sure your appliance is properly installed and grounded by a qualified technician. ~ Before installing the Tepan Yaki, check for externally visible damage. Do not operate a damaged appliance.
IMPORTANT SAFETY INSTRUCTIONS Safety ~ The appliance is hot during use and remains so for some time after being switched off. Be careful not to touch the appliance if it may still be hot. ~ Protect your hands with oven mitts or potholders when using the appliance. Use only dry, heat resistant potholders. Moist or damp potholders used on hot surfaces can result in steam burns. Do not let the potholder touch the hot heating elements. Do not use towels or other bulky items near the appliance.
IMPORTANT SAFETY INSTRUCTIONS ~ When wiping spills on a hot appliance with a wet sponge or cloth, be careful to avoid steam burns. ~ Do not let flammable materials, i.e. cooking grease, accumulate on the appliance. ~ Do not use a steam cleaner to clean this appliance. Steam could penetrate electrical components and cause a short circuit.
Guide to the Tepan Yaki a Rear heated area Indicators b Front heated area c Cooking zone indicators d Display g On/Off indicator e Control knob, rear cooking zone h Temperature control light f Control knob, front cooking zone i "Residual Heat" indicator 7
Before using for the first time Clean the appliance Heat the appliance ^ Before using for the first time, clean the appliance with a damp cloth and dry with a soft cloth. Metal components of the appliance have a protective coating which may give off a slight odor the first time the appliance is heated. The smell will dissipate after a short time and does not indicate a faulty connection or appliance defect.
Use The Tepan Yaki is divided into two heating areas, which can be used and adjusted separately. For large quantities, you can use the entire surface for cooking. For smaller quantities, you can, for example, cook in the front and keep food warm at the back, at a lower setting. When the appliance is switched on, the On/Off indicator N and temperature control light %come on. The temperature control light "responds" to the heating element in the appliance, i.e.
Use Settings Cooking Setting Range Keep cooked foods warm 1-2 Sauté fruit, e. g. diced apples, halved peaches, sliced bananas, etc. 2-4 Sauté vegetables, e. g. sliced mushrooms, onions, peppers, etc. 5-7 Gently pan-fry fish 7-9 Quickly pan-fry meat, firm fish, eggs, pancakes, crepes, etc. 9 - 11 Pan-fry shrimp, corn on the cob, etc. 11 - 12 These settings are intended as guidelines only. The cooking time depends on the type, preparation, and thickness of the food item.
Use Grilling tips Before each use, wipe the griddle with a damp cloth, to remove dust or other residue. – It is best to pre-heat the appliance for 8-10 minutes, at the preferred cooking temperature. For power settings 9 to 12, pre-heat at level 12. – When cooking meat, the appliance should be hot, otherwise too much moisture will be lost from the meat. – Generally, the appliance requires very little fat or oil for cooking, and none is needed for marinated items.
Cleaning and care ,Do not use a steam cleaner to clean this appliance. Steam could penetrate electrical components and cause a short circuit. ^ Turn the appliance off, and allow it to cool. ^ Place a mild solution of warm water and liquid dish soap on the Tepan Yaki and allow it to soak. Clean the appliance regularly, preferably after each use. Allow the appliance to cool before cleaning. ^ Remove the built-up debris with a spatula and wipe clean with a damp cloth.
Frequently asked questions ,Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. What if the appliance does not heat up after it is turned on? Possible fault Solution The circuit breaker has tripped. Check whether a fuse is blown. If the problem persists contact Miele.
Technical Service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance. Adhere rating label sticker supplied with the appliance below.
Technical Service MieleCare (USA only) MieleCare, our Extended Service Contract program; gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts. Only genuine Miele parts installed by factory trained professionals can guarantee the safety, reliability and longevity of your Miele appliance.
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and appliance damage read these instructions before installation or use.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS Note to the installer: Please leave this instruction book with the consumer for the local electrical inspector’s use. The minimum distances given in these Installation Instructions must be observed in order to ensure safe operation. Failure to do so increases the risk of fire. The cabinetry and venting hood should be installed first to prevent damage to the appliance.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS Safety distances above the appliance The minimum safety distance given by the hood manufacturer must be maintained between the cooktop and the hood above it. See the installation instructions of the hood for these safety measurements. If the hood manufacturers instructions are not available or if flammable objects are installed over the cooktop (e.g. cabinets, utensil rail, etc.), a minimum safety distance of 30" (760 mm) must be maintained.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS Safety distances to the sides of the appliance The appliance should only be installed as shown in the illustrations, while maintaining the required safety distances shown. Do not install the appliance between two tall cabinets, this is a fire hazard. A distance of at least 2" (50 mm) must be kept between the countertop cut-out and the rear wall because of the high temperatures radiated.
Installation Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintained between the countertop cut-out and the covering, since high temperatures can damage these materials. If the covering is made of a combustible material (such as wood), the distance between the countertop cut-out and the wall covering must be a minimum of 2" (50 mm).
Installation Installation dimensions a Spring clips b Appliance front c Installation height d Power supply box with connection cable, L = 78 3/4" (2000 mm) e Rating label 22
Installation Cut out ^ Make the countertop cut-out for the desired number of appliances. Remember to maintain a minimum safety distance from the back wall, as well as from any tall unit or side wall to the left or right of the combiset. See also the "IMPORTANT INSTALLATION SAFETY INSTRUCTIONS". If during installation the seal around the frame does not sit flush with the countertop in the corners, the corner radius, maximum 3/16" (4 mm), can be carefully filed down to fit.
Installation Installation of multiple appliances When installing more than one combiset appliance, a support bar b must be installed between the appliances. Countertop cut-out two appliances Countertop cut-out three appliances For the installation of two appliances the width of the countertop cut-out D is the sum of A and C. For the installation of three appliances the width of the countertop cut-out D is the sum of A and B and C.
Installation Sample calculations for a countertop cut-out for three appliances A appliance width minus 5/16" (8 mm) B appliance width C appliance width minus 5/16" (8 mm) D Countertop cut-out 11" (280 mm) 11 5/16" (288 mm) 11" (280 mm) 33 3/8" (848 mm) 11" (280 mm) 15" (380 mm) 14 5/8" (372 mm) 40 5/8" (1032 mm) 11" (280 mm) 22 11/16" (576 mm) 22 3/8" (568 mm) 56 1/16" (1424 mm) 11" (280 mm) 37" (940 mm) 14 5/8" (372 mm) 44 1/4" (1124 mm) 14 5/8" (372 mm) 22 11/16" (576 mm) 22 3/8' (568
Installation a Spring clips b Support bars c Space between support bar and countertop d Cover The illustration represents the attachment of spring clips a and support bars b for 3 appliances. An additional support bar is required for each additional appliance. The position for attachment of an additional support bar depends on the width of appliance B.
Installation Attach the spring clips and support bars Wood or solid surface countertops ^ Place the supplied spring clips a and the support bars b at the marked positions as shown above, by laying them on the upper edge of the cut-out and then securing them with the 1/8" x 1" (3.5 x 25 mm) screws (supplied).
Installation Granite countertop The screws are not needed for granite countertops. ^ Coat the side and lower edges of the spring clips between a and b with silicone. ^ Position and attach the spring clips a and support bars b with strong, double-sided tape c. 28 ^ Fill the space e between the support bars b and the countertop with silicone.
Installation Installing the appliance(s) ^ Feed the power cord down through the cut-out. ^ Place the front edge of the appliance into the cut-out. ^ With a hand on each side of the appliance press down evenly on the edges until it clicks into position. When doing so make sure that the appliance seal sits tightly on the countertop to ensure it is sealed correctly. This is important to ensure an effective seal. Do not permanently seal into the countertop.
Installation Sealing Tiled surfaces The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. The grouting a and shaded area under the appliance frame must be flat and even so that the frame will lie evenly and the sealing strip under the edge of the upper part of the appliance can provide an adequate seal against the countertop.
Electrical connection ,CAUTION: Before installation or servicing, disconnect the power supply by either removing the fuse, shutting off the main power or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous.
Help protect our environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
Alteration rights reserved / 0112 M.-Nr. 09 054 720 / 00 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
