Operating Instructions Heat-pump Dryer It is essential to read these operating instructions before installing, starting up, and using the appliance. This prevents both personal injury and damage to the appliance. en-US M.-Nr.
Contents Caring for the environment ................................................................................. 5 IMPORTANT SAFETY INSTRUCTIONS ................................................................ 6 Operating the tumble dryer ................................................................................ 14 Control panel ......................................................................................................... 14 How the display works .......................................
Contents Fragrance flacon.................................................................................................. Using the fragrance flacon .................................................................................... Removing the protective seal from the fragrance flacon.................................. Inserting the fragrance flacon........................................................................... Opening the fragrance flacon ....................................................
Contents Installation ............................................................................................................. Leveling the tumble dryer................................................................................. Ventilation ......................................................................................................... Before moving the tumble dryer again ............................................................. Additional installation requirements ...................
Caring for the environment Disposal of the packing material The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of your old appliance Electrical and electronic appliances contain valuable materials.
IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: WARNING This tumble dryer is intended for use in domestic households and similar working and residential environments. It is essential to read all instructions before using the appliance. Do not allow children to play on or in the appliance. Close supervision is necessary when the appliance is used near children.
IMPORTANT SAFETY INSTRUCTIONS Important information regarding use of fabric softener sheets: We do not recommend use of fabric softener sheets. Use of fabric softener sheets can clog the surfaces of the lint filters, extending the drying time and increasing energy consumption. During subsequent cleaning, the plastic and surfaces of the lint filters can be damaged! The best results are obtained by using liquid fabric softener in the washing machine. Follow the manufacturer's instructions.
IMPORTANT SAFETY INSTRUCTIONS To prevent the risk of fire, the following textiles must not be dried in this dryer: – items which have not been washed. – items, such as work-wear, exposed to grease, oils, or other deposits (such as lotions or cosmetics) in your dryer. If these items have not been thoroughly cleaned there is a danger that they may contribute to a chemical reaction that could cause the laundry to ignite when heated even after being removed from the dryer.
IMPORTANT SAFETY INSTRUCTIONS Allow the dryer to complete each stage of the program selected, including the cooling down phase. This will ensure that the items being removed are not too hot to handle. Clean the lint filter before or after each load. Keep the area around the air intake (toe kick) and adjacent surrounding areas free from lint, dust and dirt. The interior of the machine should be cleaned periodically by qualified personnel. GROUNDING INSTRUCTIONS This appliance must be grounded.
IMPORTANT SAFETY INSTRUCTIONS Do not modify the plug provided with the appliance: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Before installation, disconnect the tumble dryer from the electrical supply by shutting off the power main, unplugging the power cord or tripping the circuit breaker. Do not restore power until the installation is complete. Miele tumble dryers and Miele washing machines can be installed as a washer-dryer stack.
IMPORTANT SAFETY INSTRUCTIONS Heat-pump technology and refrigerant: The heat pump in this tumble dryer uses a gaseous refrigerant which is condensed by the compressor. The refrigerant, which is brought to a higher temperature level and liquified by condensing, is led in a closed circuit through the heat exchanger unit where heat exchange with the circulating drying air takes place. – The humming noises caused by the heat pump during the drying process are normal.
IMPORTANT SAFETY INSTRUCTIONS Using a fragrance flacon (optional accessory) Only use genuine Miele original fragrance flacons. Store the fragrance flacon in its original packaging. Caution: The fragrance can leak out of the flacon! Make sure that you always keep the flacon, or the lint filter with the flacon inserted in it, in a horizontal position when carrying and do not tip or place it down on any surface.
IMPORTANT SAFETY INSTRUCTIONS FCC Declaration of Conformity This appliance complies with Part 15 of the FCC regulations. This appliance has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and is subject to the following conditions: This appliance does not cause harmful interference. The appliances may be interconnected as desired.
Operating the tumble dryer Control panel a Display b Sensor buttons for the drying levels c Indicator lights light up when necessary d Gentle sensor button for gentle drying e Time display for the program duration 14 f Sensor buttons for the time selection g Start/Stop sensor button for program start/cancellation h Optical interface for service technicians i Program selector for selecting program and for switching off.
Operating the tumble dryer How the display works Indicator lights – lights up when the condensed water container needs to be emptied. – lights up when the plinth filter needs to be cleaned. The , , , and sensor buttons react to fingertip contact. Selection is possible as long as the respective sensor button is illuminated.
Operating the tumble dryer Time display Drum lighting The remaining program duration will be displayed in hours and minutes. The inside of the drum lights up so that you don't forget any items of laundry when you empty it. The drum lighting switches off automatically (energy saving). With most program, the duration displayed may vary or “jump”.
Energy saving tips This dryer with heat-pump technology is designed for energy-saving drying cycles. However, you can save a little more energy with the following measures as the drying time is not extended unnecessarily. – Make sure your laundry is spun at the maximum spin speed before drying. The higher the spin speed, the greater the savings that can be made in energy and time during drying, e.g., approx. 20% energy can be saved if spun at 1,600 rpm instead of 1,000 rpm.
Functioning of the heat-pump dryer Two separate circuits ensure that the laundry is dried: Dry air circuit The drying air flows through a heat exchanger, the drum, and several filters. This is ensured by a blower in the dryer. – The drying air flows through the heat exchanger in the longitudinal direction and is heated in the rear area. – The drying air is then blown into the drum, where it absorbs the moisture of the laundry.
Initial set-up Removing the protective film and stickers Remove: – The protective film from the door – Any stickers (if present) from the front and the lid Please do not remove any labels (e.g., the data plate) which are visible when you open the door. Carrying out the procedure for initial commissioning outlined in these instructions Read “1. Notes on correct laundry care” and “2. Loading the tumble dryer”. You can then load the tumble dryer and select a program as described in “3.
1. Notes on correct laundry care Points to note regarding washed laundry – When washing very heavily soiled items, ensure that you use sufficient detergent and select a high temperature. If in doubt, wash the items several times. – Do not load the drum with items that are still soaking wet. Make sure your laundry is spun at the maximum spin speed before drying. The higher the spin speed, the greater the savings that can be made in energy and time during drying.
1. Notes on correct laundry care Drying Tip: See the “Program chart”. This describes the programs and gives their maximum load. – Always observe the maximum recommended load for each program. This will mean that the energy consumption for the amount of laundry is at its most economical. – Down-filled garments have linings which have a tendency to shrink, depending on the quality of the item. Only use the Smoothing program for these items.
2. Loading the tumble dryer Loading the laundry Textiles may be damaged. Before loading, read “1. Notes on correct laundry care”. Unfold the laundry and load loosely into the drum. Do not overload the drum. Overloading can cause unnecessary wear and tear to the laundry, give a disappointing drying result, and cause more creasing. Socket for the fragrance flacon The “Fragrance flacon” chapter describes how to use the fragrance flacon.
3. Selecting a program and starting it Selecting a program The tumble dryer is switched on when you select a program and switched off by turning the program selector to the position. Selecting drying levels during drying level programs Normal, Wrinkle-free, Delicates, Dress Shirts, Express, Denims, Bed Linens, Smoothing The pre-set drying level can be changed if required. Turn the program selector. A drying level may light up and durations will appear on the time display.
3. Selecting a program and starting it Time-controlled and other programs Time Dry You can set the duration in ten-minute increments from minutes to hours. Selecting Gentle Delicate fabrics (with the symbol on the care label, e.g., acrylic garments) are dried at a lower temperature and the program duration is longer. Touch the Gentle sensor button. It will then light up brightly.
3. Selecting a program and starting it Sequence Selecting Delay Start You can delay the start of a program from minutes up to hours. However: Delay Start cannot be used with the Time Dry program. – Delay start times of more than will count down in hours and then in minutes until the start of the program. – The drum will turn briefly every hour until the start of the program to reduce laundry creasing. Touch the sensor button. will light up brightly.
3. Selecting a program and starting it Starting a program Energy savings Touch the flashing Start/Stop sensor button. After 10 minutes, the indicators dim and the Start/Stop sensor button starts flashing. The Start/Stop sensor button will light up. Notes If a delay start time has been selected, then this will count down on the time display.
4. Removing the laundry at the end of the program End of program/Anti-crease End of program: lights up and the Start/Stop sensor button goes out. After the program has finished, the drum continues to rotate at intervals for a max. of 2 hours to reduce creasing. There is no Anti-crease phase with Woolens/Silks. See “Programmable functions“, “ Anti-crease”. Energy savings – 10 minutes after the end of the program, the Start/Stop sensor button will begin to flash and the display will go out.
Program chart All weights marked with * are based on the weight of dry laundry. Normal Full load (17.6 lb/8 kg)* Extra, Normal Items Single and multi-layered cotton items. For example, T-shirts, underwear, baby clothes, workwear, jackets, covers, aprons, overalls, hand towels, bath towels, bathrobes, and bed linen. Tip – Select Extra for multi-layered and very thick fabrics. – Do not use Extra for jersey fabrics (e.g., T-shirts, underwear, baby clothes) because they can shrink.
Program chart Smoothing Small load (2.2 lb/1 kg)* Normal, Hand iron Items – Cotton and linen fabric. – For easy care items made of cotton, mixed, or synthetic fiber. For example, pants, jackets, and shirts. Tip – This program smoothes out creasing caused during the spin cycle in the washing machine. – This program is also suitable for dry fabrics. – Please remove the garments as soon as the program has finished. Woolens/Silks Items Small load (4.
Program chart Outdoor Small load (5.5 lb/2.5 kg)* Normal, Hand iron Items Outdoor clothing which is suitable for drying in a tumble dryer. Proofing Small load (5.5 lb/2.5 kg)* Items For drying microfiber fabrics, skiwear, outdoor wear, fine, closeweave cotton garments (poplin), and table linen which are suitable for drying in a tumble dryer. Note – Items are dried to a Normal level only. – This program includes a proofing fixing phase.
Changing the program sequence Changing a program once it has started Cancelling the current program You cannot change to another program once a program has started (this prevents unintentional alterations). The items will be cooled down, depending on the temperature reached and how long they have been dried for. will light up if you press the Start/ Stop sensor button again during the cooling-down phase. If you try to change a program, will light up until the original program is reset.
Changing the program sequence Adding laundry during ongoing delay start period You can open the door to add or remove laundry. – All program settings will be saved. – You can still change the drying level, if required. Open the door. Remove or add the laundry. Close the door. Touch the Start/Stop sensor button so that the delay start period continues. Program duration Altering the program sequence can cause the program duration shown on the time display to be adjusted.
Condensed water container Emptying the condensed water container The condensed water is collected in the condensed water container. Empty the condensed water container after every drying program. The indicator light will light up if the maximum level of the condensed water container is reached. To turn the indicator light off: Open and close the door while the dryer is switched on. Empty the condensed water container. Replace the condensed water container in the dryer.
Fragrance flacon Using the fragrance flacon Using the fragrance flacon (optional accessory) will add a pleasant fragrance to your laundry. Risk of fire and damage to the Removing the protective seal from the fragrance flacon Only hold the fragrance flacon as illustrated. Do not hold it at an angle or tip it as the fragrance will leak out of the flacon. health if fragrance flacons are used incorrectly. The leaked fragrance can damage your health if it comes into contact with your body.
Fragrance flacon Inserting the fragrance flacon Open the door of the tumble dryer. The fragrance flacon is inserted in the upper lint filter next to the recessed grip. Markers and must line up with one another. Open the cover using the tab until the tab is right at the top as shown. Turn the outer ring clockwise a little. The fragrance flacon can slip out. Turn the outer ring in such a way that markers and line up. Insert the fragrance flacon into the socket as far as it will go.
Fragrance flacon Opening the fragrance flacon Closing the fragrance flacon Before drying, you can select the intensity of the fragrance. After drying, the fragrance flacon should be closed to prevent the fragrance from escaping needlessly. Turn the outer ring clockwise: The further you open the fragrance flacon, the more intense the fragrance. Damp laundry and longer drying durations with sufficient heat transfer are needed for the fragrance to be released into the laundry effectively.
Fragrance flacon Removing/replacing the fragrance flacon Turn the outer ring counter-clockwise until markers a and b line up. Replace the fragrance flacon with a new one. When not in use, you can store the fragrance flacon in its original packaging. Fragrance flacons are available to order from Miele retailers or online. The fragrance can leak out of the pod. Do not lay the fragrance flacon down.
Cleaning and care Lint filters This tumble dryer has 2 lint filters in the door opening: The upper and lower lint filters trap lint produced during the drying process. Clean the lint filters after each drying program. This prevents an extension of the program duration. Also clean the lint filters when the indicator light comes on. To turn the indicator light off: Pull the upper lint filter forward to remove it. Open and close the door while the dryer is switched on.
Cleaning and care Remove the lint (see arrows) from the filter surface of all the lint filters and the perforated laundry deflector. Turn the yellow dial on the lower lint filter in the direction of the arrow (until you hear it click). Push the upper lint filter back into position until it clicks. Close the door.
Cleaning and care Cleaning the lint filters with water Wipe the smooth plastic surfaces of the lint filters with a damp cloth to clean them. Flush the lint filters through with warm running water. Shake the lint filters thoroughly and then dry them carefully. Hold the dial and pull the lint filter forward to remove it. Ensure the filters are dry before replacing them. Wet filters could cause operational faults. Push the lower lint filter in completely and lock it with the yellow dial.
Cleaning and care Cleaning instructions when using fabric softener sheets If you are using fabric softener sheets, please follow these warnings and instructions. Option 3 Wet the surfaces of the lint filters with a liquid color detergent (e.g., Miele Ultra Color Liquid Laundry Detergent). Leave it on for approx. 2 hours. First, clean the filters as Risk of fire! described in “Cleaning the lint filters with water”.
Cleaning and care Cleaning the plinth filter Removing the plinth filter Clean the plinth filter whenever the indicator light comes on or when the program duration is longer than usual. To turn the indicator light off: Open and close the door while the dryer is switched on. Press the round, indented area on the heat exchanger access panel to open it. The panel will spring open. Pull the plinth filter out by the handle. This causes the right-hand guide pin in the dryer to come out.
Cleaning and care Cleaning the plinth filter Cleaning the plinth filter flap Pull the handle out of the plinth filter. You can brush off a heavy build-up of lint on the plinth filter or remove it with a vacuum cleaner. Use a damp cloth to remove any lint. Make sure that you do not damage the rubber seal when doing this. Clean the filter thoroughly under running water. Check whether the cooling fins are blocked with lint (as follows). Squeeze the water out of the plinth filter thoroughly.
Cleaning and care Checking the heat exchanger unit Inserting the plinth filter Risk of injury from sharp cooling fins. You could cut yourself. Do not touch the cooling fins with your hands. Look to see if lint has accumulated. If there is visible soiling: Damage due to incorrect cleaning of the heat exchanger. The dryer will not dry if the cooling fins are damaged or bent. Use a vacuum cleaner with a dusting brush attached to clean the cooling fins.
Cleaning and care Damage or ineffective drying if drying takes place without a plinth filter or when the heat exchanger flap is open. Excessive accumulations of lint can damage the dryer in the long term. If the system is not leak-tight, this can make the drying ineffective. You may only operate the dryer with the plinth filter fitted correctly and the heat exchanger flap closed. Cleaning the dryer Disconnect the tumble dryer from the electrical supply.
Frequently Asked Questions With the help of the following guide minor faults in the performance of the machine, some of which may result from incorrect operation, can be remedied without contacting the Service Department. This guide may help you to find the reason for the fault, and how to correct it. Indicator lights or information on the time display Problem Possible cause and solution The indicator light comes on after a program has been cancelled and a signal sounds.
Frequently Asked Questions Problem Possible cause and solution flashes/lights up Access via a code has been activated. See “Programmable functions“, “ Code”. after the tumble dryer is switched on and a program cannot be selected. and light up after a program has been cancelled, a signal sounds. An excessive amount of lint has built up. Clean the lint filters. Clean the plinth filter. Clean the airways: the area underneath the plinth filter and the heat exchanger.
Frequently Asked Questions Unsatisfactory drying results Problem Possible cause and solution The laundry is not sufficiently dry. The load consisted of different types of fabric. Finish drying using the Time Dry program. Select a more suitable program next time. Useful tip: You can alter the drying levels for some programs. See “Programmable functions“, sections “ Drying levels “Normal”“ and “ Drying levels “Wrinkle-free””. The laundry or featherfilled pillows develop a smell after drying.
Frequently Asked Questions The drying cycle duration is very long Problem Possible cause and solution The drying process goes on too long or even switches off.* The room in which the tumble dryer is located is too warm. Ventilate the room thoroughly. Detergent residues, hair, and fine lint can clog the filters. Clean the lint filters and the plinth filter (see “Cleaning and care”, sections “Cleaning the lint filters” and “Cleaning the plinth filter”).
Frequently Asked Questions Other problems Problem Possible cause and solution You can hear operating noises (buzzing/ humming). This is not a fault. The compressor is operating. These noises are quite normal and can be heard when the compressor is operating. A program does not start. There is no obvious cause. Connect the power plug. Turn on the tumble dryer. Close the door. Check whether the fuse has tripped.
Technical Service Contact in case of fault Warranty In the event of a fault which you cannot remedy yourself, please contact your Miele dealer or Miele Technical Service. For further information, please refer to your warranty booklet. Contact information for Miele Technical Service can be found at the end of this document. Optional accessories Optional accessories for this tumble dryer are available from your Miele dealer or Miele Technical Service.
Installation instructions Alteration rights reserved. Visit our website for all the current product specifications, technical appliance information, and warranty information. To avoid accidents or damage to the appliance, please read these instructions before installing and/or using it.
IMPORTANT SAFETY INSTRUCTIONS , WARNING - Risk of Fire To reduce the risk of severe injury or death, follow all installation instructions. Clothes dryer installation must be performed by a qualified installer. Install the clothes dryer according to the manufacturer's instructions and local codes. Repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and could void the warranty.
IMPORTANT SAFETY INSTRUCTIONS The installation of this unit in non stationary locations (e.g. ships) must be performed by a qualified installer or service agency, in strict accordance with national and local safety regulations and standards. Do not install the machine in rooms where temperatures below freezing may occur. If there is any doubt concerning installation, contact Miele’s Technical Service Department. USA 1-800-999-1360 TechService@mieleusa.com CDN 1-800-565-6435 service@miele.
Installation and connection Front view a Drain hose for condensed water b Power cord – Observe the section entitled “Electrical connection”.
Installation and connection Rear view a Protruding lid for holding when moving the tumble dryer (see arrows) b Drain hose for condensed water c Hook for winding the power cord during transport d Power cord Transporting the tumble dryer Danger of injury to people and damage to property caused by moving the appliance incorrectly. If the tumble dryer tips up, there is a danger of injury to people and damage to property. Ensure that the tumble dryer is stable during transportation.
Installation and connection Installation Leveling the tumble dryer Ensure that no closeable door, sliding door, or an oppositely hinged door is installed that would hinder the door of the dryer being opened in any way. Ventilation The cool air intake at the front of the dryer must not be blocked or covered. This would hinder a sufficient intake of cool air for the heat exchanger. Do not block the gap between the bottom of the tumble dryer and the floor with toe kicks, deep pile carpet, etc.
Installation and connection Additional installation requirements All installations must be carried out in accordance with local regulations. Slot-in This tumble dryer is suitable for pushing under a countertop. Installing the dryer in a closet Minimum installation distance You must insert sufficiently large ventilation openings into the closet door. You can also open the closet door slightly while the dryer is operating. Otherwise, the dryer can overheat, which can cause a fault.
Installation and connection Installing the dryer in a floor-to-ceiling closet You can also insert a ventilation opening at the top of the closet. In addition, you must also provide an opening on the bottom side of the closet door. Direct ventilation is also possible via an air conditioning outlet in the closet. The air must be able to circulate freely at the top of the closet. The air supply must not be hindered by a shelf.
Installation and connection Product dimensions Dimensions 5.2 ft (1.6 m) drain hose, detachable, top right on the rear 6.
Installation and connection Electrical connection GROUNDING INSTRUCTIONS The electrical safety of this dryer can only be guaranteed when continuity is complete between it and an effective grounding system. It is essential that this standard safety requirement is observed and regularly tested. If in any doubt, please have the electrical installation inspected by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate grounding system.
Installation and connection External draining of condensed water Note When drying is in progress, condensed water is pumped into the condensed water container through the drain hose which is located at the back of the dryer. The condensed water can also be externally drained away via the drain hose on the back of the dryer. This means that the condensed water container no longer has to be emptied. Drain hose length: 5.2 ft (1.6 m) Maximum delivery head: 4.9 ft (1.
Installation and connection Changing the door hinging You can change the door hinging on this tumble dryer yourself. For safety reasons, the tumble dryer must be disconnected from the electricity supply before changing the door hinging. You will need: – a Torx T20 and T30 screwdriver – a flat head screwdriver or pointed pliers Hold the door securely and pull it forwards: to remove the door you will need to pull the base plate of the hinge with its 2 pins out of the dryer.
Installation and connection Turn the door lock by 180°. Press the door lock into the openings on the opposite side of the door opening. 3. Remove the lock catch from the door First take the rubber seal off the door and place this to one side. Adjust the position of the door lock so that the screw holes line up with those in the front panel of the dryer . Screw in both Torx screws in order to secure the door lock. Use a T20 Torx screwdriver to remove screw on the lock catch.
Installation and connection 4. Dismantle the door hinge from the door The door hinge cover must be unclipped from position and then removed. Remove the lock catch from the cover. This lock catch cover is no longer needed. Use a screwdriver to press down gently on position on the door hinge cover. Using a little force, pull out door hinge cover . This lock catch cover is no longer needed. Insert the lock catch into the new cover supplied with the dryer.
Installation and connection 5. Change the door hinge on the door The door hinge is secured to the door with 2 angled rods. These rods need to be removed with a screwdriver or pointed pliers. Tip: In some circumstances, the rods can be difficult to dislodge. Moving the screwdriver with a levering action while pulling at the same time may help to work the rods free. Remove the door hinge and turn it by 180°. Refit the door hinge on the opposite side of the door.
Installation and connection You now need the new door hinge cover supplied with the dryer. 6. Change the lock catch on the door You now need the new lock catch cover supplied with the dryer which you have already fitted with the lock catch. Fit new door hinge cover and clip it into position. Push the lock catch cover with its lock catch into position. Tighten the screw .
Installation and connection Refitting Now that you have changed the 7. Refit the door door hinging, the door will open from the opposite side. Press the rubber seal back into the groove on the door. Position the door in front of the dryer. Fit the base of the door hinge with its 2 pins into the openings on the dryer. The base of the door hinge must be flush with the front panel of the dryer. The door cannot fall off in this position.
Technical data Height 33 7/16" (850 mm) Width 23 7/16" (596 mm) Depth 25 5/16" (643 mm) Depth with door open 42 3/8" (1077 mm) Slot-in Yes Stackable Yes Weight Approx. 137 lbs (62 kg) Drum volume 31.7 gal (120 l) Load quantity 17.6 lb (8 kg) dry laundry Capacity of condensed water container 1.27 gal (4.8 l) Hose length 63" (1.60 m) Maximum head height 59" (1.
Programmable functions Programming You can use the programmable functions to alter the dryer's electronics to suit your requirements. Programming is carried out in these steps (, , ... ) using the sensor buttons. Accessing the programming level Before you begin, ensure the following: – The dryer is switched on and any program is selected. Choosing and selecting programmable functions The number of the programmable function will appear on the display as and a number: e.g., .
Programmable functions Editing and saving the programmable function You can either switch a programmable function on or off or select different options. The programmable function option will appear on the display as and a number: e.g., . The number of the programmable function, e.g., , will then light up again. Exiting the programming level Turn the program selector to the position. The settings have been changed. You can alter the settings again at any time.
Programmable functions Drying levels “Normal” You can adjust the drying levels for the Normal program to one of seven different levels. Buzzer volume The buzzer volume can be changed. You will hear it as it changes. Options = Even damper = Damper = A little damper = Factory setting = A little drier = Drier = Even drier Exception: The Normal program will remain unchanged.
Programmable functions Code The code prevents your dryer being used without your knowledge. When the code has been activated, you have to enter the code after switching the dryer on. Otherwise, the dryer cannot be operated. Options = Off (factory setting) = On If the option has been selected, after switching on you will have to enter the code before you can operate the dryer. Using the dryer when the code is activated After the dryer is switched on, will flash on the time display.
Programmable functions Display switch-off status To save energy, the time display and sensor buttons will go out after 10 minutes, and only the Start/Stop sensor button will flash. You can alter this setting. However, there is no switch-off in the event of a fault. Options = Off The time display and sensor buttons will remain lit up while the dryer is switched on. = On (factory setting) The time display and sensor buttons will go out after 10 minutes. . . . . .
Programmable functions Memory You can set the following: The electronic module will save the drying level and any options selected for the current drying program. It will also save the duration of the Time Dry program. When the program is selected again, these saved settings will appear on the display. Options = Off (factory setting) Buzzer on The buzzer sounds to let you know the program has finished. It can be switched on or off.
Programmable functions Airway indicator Lint should be removed after drying. The indicator light will also come on when a certain amount of lint has collected in the filters. You can decide at what level of lint this reminder should be given. You will have an idea of how often this should be done after a few drying programs. Options = Off The indicator light does not come on.
Please have the model and serial number of your appliance available when contacting Technical Service. U.S.A. Canada Miele, Inc. Importer Miele Limited National Headquarters 9 Independence Way Princeton, NJ 08540 Phone: 800-843-7231 609-419-4298 Fax: www.mieleusa.com Technical Service & Support Phone: 800-999-1360 888-586-8056 Fax: TechnicalService@mieleusa.com International Headquarters Miele & Cie.
TWB 120 WP en-US M.-Nr.