Operating Instructions Freestanding coffee machine CM 5100 To prevent accidents and machine damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 First steps to use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Before the first use . . . . . . . . . . . . . . .
Contents Time of day and clock display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 System lock . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances basic safety precautions should always be followed, including the following: Read all instructions before installation or use of the coffee system. Proper use Please read these instructions carefully to prevent accidents and machine damage. This appliance complies with current safety requirements. Improper use of the appliance can cause personal injury and material damage. ~ This coffee system is not designed for commercial use.
IMPORTANT SAFETY INSTRUCTIONS Technical safety ~ Be sure the vents at the top of the ~ Before installing the appliance, machine are not completely covered, e.g. with a dish towel. check for externally visible damage. Do not operate a damaged appliance. ~ Before connecting the appliance to the electrical supply make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. If in doubt, consult a qualified technician.
IMPORTANT SAFETY INSTRUCTIONS ~ Never open the outer casing of the appliance. Tampering with electrical connections or components and mechanical parts is dangerous and may cause machine damage. ~ To protect against fire, electric shock and injury to persons do not submerge the cord or plugs in water or other liquids. ~ If the coffee system will not be used for an extended period of time, turn it off by using the main power switch. Safety Use Caution. There is a risk of burns when dispensing beverages.
IMPORTANT SAFETY INSTRUCTIONS ~ Never place a cup with an alcohol-coffee mixture under the coffee dispenser. Plastic parts of the unit could catch fire! ~ Do not place anything that produces an open flame such as a candle on top of or next to the coffee machine. Danger of fire! ~ Disconnect the coffee machine from the electrical supply before cleaning. ~ Clean the coffee system daily, see "Cleaning and care". ~ Do not use a steam cleaner to clean the coffee system.
Guide to the machine a Cup warming surface b Bean container, ground coffee chute and rotary selector to control the fineness of the ground coffee c Display and controls k Cappuccinatore control, to select hot milk, hot water or milk froth l Air intake nozzle m Dispenser n Milk flask with tubing d Steam and hot water dispenser e Cappuccinatore (see inset diagram) f Coffee dispensers g Drip tray cover h Drip tray and waste container i Main switch j Water tank 8 Cappuccinatore symbols: - Hot water z Mi
Guide to the machine Display and controls Control Action Function a Coffee button / Press To dispense coffee b Espresso button . Press To dispense espresso c On/Off button - Press Turns the machine On/Off (Standby mode) d Rotary selector Turn in either direction Displays options or settings e OK button Press Confirms a selection or action Cancels beverage preparation Brings up the SETTINGS menu (Press and hold for 2 seconds) The OK button will light up if the option is available.
Accessories The following accessories come included with your coffee system: – Measuring spoon for ground coffee – Cleaning tablets to clean/degrease the brew unit Optional accessory – Microfiber cloth (optional accessory) for removing finger prints and light soiling – Descaling tablets for descaling the water pipework – Test strips to determine the water hardness level – Milk flask for storing and preparing milk 10 These accessories and others are available from your Miele dealer or online at www.
First steps to use Before the first use Clean the appliance and remove protective foils before the first use. See "Cleaning and Care". Turning on When the coffee system is turned on for the first time and after the welcome screen appears, you will be prompted to set the following: ^ Plug in the appliance. If the power cord is too long, it can be pushed into the hole in the back of the unit. – Language ^ Fill the coffee bean container. See "Filling the beans container").
First steps to use Setting the clock format Water hardness ^ Turn the rotary selector until the desired clock format (12 hour or 24 hour) appears in the display. The hardness of the water used in the coffee system must be determined and programmed into the appliance. The water hardness will determine how frequently the unit must be descaled to maintain the coffee system properly.
First steps to use Setting the water hardness ^ In the main menu, press the OK button for two seconds. < SETTINGS WATER HARDNESS > ^ Turn the rotary selector until WATER HARDNESS appears in this display. Confirm with OK. ^ Turn the rotary selector until the desired water hardness level appears in the display. Confirm with OK. The setting is now saved.
Filling the water tank The quality of the water used plays an important part in the overall quality of the coffee. The water tank should be emptied and filled with fresh, cold tap water. Hot or warm water, or other liquids could damage the coffee system. Do not use mineral water. Mineral water will cause lime scale deposits to build up in the machine, possibly damaging it. ^ Open the lid on the left hand side of the coffee system a. Pull the water tank up and out using the handle b.
Filling the coffee bean container Fill the coffee bean container with roasted espresso or coffee beans. Important: Only use roasted espresso or coffee beans in the container. Anything else, including ground coffee, will damage the grinder. Important: Do not use coffee beans that have been treated with sugar, caramel or other substances. Do not put drinks containing sugar in the coffee bean container. Sugar will damage the machine. ^ Open the lid on the right of the coffee system a.
Turning the machine On / Off The On/Off - button (Standby) can be used to turn the coffee system on or off, if the main switch at the back of the machine is turned on. Turning on When the On/Off - button is pressed, the coffee system will heat up. If the coffee system was used recently and still has an operating temperature higher than 140°F (60°C), rinsing will not take place. ^ Press the On/Off button -.
Pre-heating cups In order to allow the flavor of the coffee to develop and be retained, the cups should be pre-heated. The smaller the volume of coffee/espresso and the thicker the cup, the more important it is to pre-heat the cup. Pre-heating cups using the cup warming function The cup warmer on the top of the coffee system can be used to pre-heat coffee cups and glasses. The cup warming function must be turned on. TIP Cups can also be warmed with hot water by using the - button.
Preparing coffee or espresso When the / or . buttons are pressed, the coffee system automatically grinds the beans to brew the coffee. Preparing two portions at one time Two portions of coffee or espresso can be prepared at the same time. The coffee system will make two portions one right after the other. ^ Place a cup under the coffee dispensers. ^ Press the button for the desired beverage: / for coffee, or . for espresso. The chosen beverage will now be dispensed.
Preparing coffee or espresso Canceling preparation The coffee/espresso preparation can be canceled when STOP? appears in this display. Any coffee beans which have already been ground will be directed into the waste container. ^ Press the OK button. Adjusting the height of the coffee dispensers The coffee dispensers can be raised or lowered to the height of your cup. If the dispensers are closer the beverage will not cool down as quickly and the crema will have a better consistency.
Making coffee or espresso using ground coffee One portion at a time of coffee or espresso can be using ground coffee. This allows you to prepare a decaffeinated coffee, if the bean container is already filled with regular coffee beans for example. The coffee system will automatically recognize that ground coffee has been placed in the chute. Use the scoop supplied with the machine to ensure the correct amount of ground coffee is used.
Making coffee or espresso using ground coffee Preparing coffee/espresso using ground coffee The following message appears in this display: SELECT DRINK USE GROUND COFFEE ^ Place a cup under the coffee dispensers. Canceling preparation Coffee preparation can be canceled when STOP? appears in this display. Any coffee which has already been ground will be directed into the waste container. ^ Press the OK button. The preparation will be canceled.
Frothing and heating milk The coffee system draws milk through a tube from the milk flask. Steam is then used to heat the milk in the cappuccinatore. If desired, the milk can also be frothed this way. In order to produce the best milk froth, use cold milk. The milk flask will keep the milk cold for an extended period of time. Preparing the milk flask ^ Connect the stainless steel angled end of the milk tube to the top of the lid until it clicks into place.
Frothing and heating milk Preparing milk froth ^ Turn the cappuccinatore dial to z. ^ Place a cup or suitable container under the cappuccinatore. ^ Press the * button. The coffee system will heat up. HEATING-UP PHASE will appear in the display. After heating the milk froth will be dispensed into the container underneath. ^ Press the OK button when enough milk froth has been prepared. TIP For best results use cold milk.
Frothing and heating milk Preparing hot milk Canceling preparation Milk preparation can be canceled when STOP? appears in this display. ^ Press the OK button. The preparation is canceled. After preparing milk ^ Turn the cappuccinatore dial to the J position. ^ Place a cup or suitable container under the cappuccinatore. ^ Press the * button. The machine will heat up and HEATING-UP PHASE will appear in the display.
Frothing and heating milk Milk temperature Preparing a cappuccino The cappuccinatore dial can be used to adjust the temperature of the milk. ^ Fill the cup half way with milk froth. ^ Place the cup under the coffee dispensers and prepare an espresso. Preparing a Latte Macchiato ^ Fill a Macchiato glass one third full with hot milk. ^ Top the hot milk with one third of milk froth. ^ Turn the dial to: a for warm milk, or b for hot milk.
Preparing hot water If the cappuccinatore has been used to prepare hot milk or milk froth, the cappuccinatore needs to be rinsed. See "Cleaning and care". Use caution. Danger of burning or scalding on the cappuccinatore. The liquid and steam dispensed are very hot. ^ Turn the cappuccinatore dial to -. ^ Place a cup or suitable container under the cappucinatore. ^ Press the - button. ^ Press the OK button when enough hot water has been prepared.
Adjusting the grinder setting The grinder setting should be adjusted to suit the type of coffee you are using. ^ Place a suitable container under the coffee dispensers. When the beans are ground correctly the coffee or espresso will flow evenly into the cup and have a good crema. ^ Open the lid on the right hand side of the coffee system. ^ Select / or .. The coffee is ground too coarse, if – the espresso or coffee flows into the cup too quickly. – the crema is very pale and uneven.
Adjusting the strength of the coffee The ground coffee amount can be set between 0.2 ounces and 0.5 ounces (6 - 14 grams). The greater the quantity the stronger the coffee or espresso will be. The coffee amount is too low, if – espresso or coffee flows into the cup too quickly. – the crema is pale and uneven. – the espresso or coffee lacks body. The coffee ground amount can be altered by selecting a different setting.
Pre-brewing the coffee During pre-brewing a small amount of hot water moistens the ground coffee before the remaining water is pushed through the grounds at high pressure. This helps release the flavor of the coffee. This function can be turned on or off. The machine is delivered with the pre-brewing function turned off. To turn the pre-brewing function on or off ^ In the main menu, press and hold the OK button for two seconds.
Brewing temperature The ideal brewing temperature depends on the type of coffee, and whether espresso or coffee is being prepared. Three temperatures are available for coffee and espresso: – low – normal – high TIP Not all coffee can withstand high temperatures. Certain types are too delicate, which could cause poor crema to form and impair the taste. To set the coffee/espresso temperature ^ In the main menu, press and hold the OK button for two seconds.
Setting the serving size The amount of water used for each serving of espresso, coffee or hot water can be set to suit your taste and cup size. For drinks prepared with milk, you can also set the duration of the steam used for heating or frothing the milk. There is a maximum amount of water that can be programmed for each type of drink. The water flow will stop automatically when the maximum amount of water has been reached. To program the serving size you can either: – use the .
Setting the serving size Setting the steam duration for hot milk and milk froth Programming the amount using the SETTINGS menu The duration of steam is the same for heating milk and for frothing milk. ^ Press and hold the OK button for two seconds. ^ Place a container with sufficient milk next to the coffee system on the right hand side. Place the milk tube into the container. ^ Turn the cappuccinatore dial to the z or J symbol. SETTINGS PROG. THE AMOUNT ^ Turn the rotary control until PROG.
SETTINGS Menu The SETTINGS menu can be used to customize the coffee system to your preferences. Options currently selected are marked with a check B. If a button has not been pressed for some time, the coffee system will revert to the main menu. How to... Action Access the SETTINGS menu In the main menu or standby mode, press and hold the OK button for two seconds. Access an option Turn the rotary selector in either direction until the desired option appears in the display. Confirm with OK.
SETTINGS Menu Options menu Option Available settings Language Deutsch (German), English and other languages Maintenance Rinse the system Descale Clean the brew unit Time of day (available in Comfort mode) Clock display 12 H / 24 H Set Timer (available in Comfort mode) Set switch on at / switch off after (1:00) / switch off at Activate switch on at (12:00) / switch off at (12:00) Prog.
Language The desired display language can be selected in the SETTINGS menu. ^ Press and hold the OK button for two seconds. < SETTINGS SPRACHE F ^ Turn the rotary selector until LANGUAGE F appears in this display. Confirm with OK. ^ Turn the rotary selector until the desired language appears in this display. Confirm with the OK button. The setting is now saved and the display will revert to the previous screen. The display now appears in the set language.
Time of day and clock display If the coffee system is being operated in Comfort Mode you can set the Time of day and the clock display in the SETTINGS menu. The clock can be displayed in a 24 hour or 12 hour clock. The time of day must be set in order for the timer to work, however it will not be visible in the display. The time of day will not be saved if there is a power failure or if the machine is turned off using the main switch. ^ Press and hold the OK button for two seconds.
Timer Setting the timer The timer is only available if you are operating the coffee system in Comfort Mode. The timer can be set so that the coffee system: – turns on at a particular time (SWITCH ON AT). – turns off at a particular time (SWITCH OFF AT). – turns off after a particular length of time if none of the buttons have been pressed and no drinks have been prepared (SWITCH OFF AFTER). ^ Press and hold the OK button for two seconds.
Timer ^ Turn the rotary control until the desired minute setting appears in the display. Confirm with OK. The setting is now saved. Once you have activated the timer function (see "To activate and deactivate the Timer"), the coffee system will turn on at the set time. Switch off after If none of the buttons have been pressed and no drinks have been prepared after one hour the coffee system will turn itself off to save energy. This time can be changed to another time ranging from 15 minutes to 9 hours.
Timer To activate and deactivate the timer If the setting "Switch on at" has been activated, the c symbol will appear in the display when the coffee system is in Standby mode. ^ Press and hold the OK button for two seconds. < SETTINGS TIMER > ^ Turn the rotary selector until TIMER appears in the display. Confirm with OK. ^ Turn the rotary selector until ACTIVATE appears in the display. Confirm with OK. ^ Turn the rotary selector until SWITCH ON AT or SWITCH OFF AT (as desired) appears in the display.
Default settings The settings can be reset to the factory default settings as they were when the machine was first turned on. Refer to the "Options menu" for the default settings marked in bold. The following settings will not be reset: - Language Time of day Number of drinks dispensed ^ Press and hold the OK button for two seconds. < SETTINGS FACTORY DEFAULT > ^ Turn the rotary selector until FACTORY DEFAULT appears in the display. Confirm with OK.
Operating modes The coffee system can be operated in either Eco Mode or in Comfort Mode. When the coffee machine is operated in Eco Mode, the following will appear in the display while the machine is heating up: < HEATING-UP PHASE ECO MODE > The coffee system is preset with Eco Mode. Eco Mode saves energy, the coffee system will switch to Standby mode if a drink has not been prepared for some time. The coffee system will heat up again when a button is pressed.
System lock The coffee system can be locked to prevent it from being used without your consent, e.g. by children. Activating / Deactivating the system lock Once the machine is turned off the system lock will be activated again and the coffee system will be locked again. ^ Press and hold the OK button for two seconds. SETTINGS SYSTEM LOCK > ^ Turn the rotary selector until SYSTEM LOCK appears in the display. Confirm with OK.
Displaying information The INFO option can be used to check: – the total number of portions of espresso, coffee, steam and hot water dispensed (TOTAL PORTIONS), – the number of portions of espresso and coffee dispensed (COFFEE), – how many times steam for hot milk and milk froth has been prepared (STEAM), – how many times hot water has been prepared (HOT WATER), and – the number of portions before descaling needs to be performed (No. PORTIONS UNTIL DESCALING).
Cleaning and care Quick guide The coffee system must be cleaned every day to prevent a build-up of bacteria. How often Necessary cleaning If it is going to be more than one hour before dispensing milk again Rinse the cappuccinatore Every day (after the last drink of the day is dispensed) Rinse the system Wash the cappuccinatore Wash the water tank Wash the milk flask. Wash the waste container Wash the drip tray and cover Once a week Wash the brew unit Approx.
Cleaning and care Allow the coffee system to cool before cleaning. The water in the drip tray can be very hot. May cause burns! Do not clean the unit with a steam cleaner. Never use cleaners containing chlorides, sand, soda or scouring agents. These will damage the surface. Rinsing the system It is important to rinse the system daily to remove any coffee residues from the coffee system. The hot water from the rinsing process also pre-warms the pipework.
Cleaning and care Rinsing the system manually The system will need to be rinsed manually if the machine has been used and the automatic rinsing is turned off. ^ Place a suitable container under the coffee dispensers. ^ In the main menu, press and hold the OK button for two seconds. < SETTINGS MAINTENANCE > ^ Turn the rotary selector until MAINTENANCE appears in the display. Confirm with OK. ^ Turn the rotary selector until RINSE THE SYSTEM appears in the display. Confirm with OK.
Cleaning and care Cappuccinatore The cappuccinatore can become clogged with milk residues, therefore it should be rinsed through if more than an hour has passed since it was last used to prepare milk. Regardless it should be taken apart and cleaned daily. Cleaning the cappuccinatore Danger of burns. The cappuccinatore is very hot after use. Allow it to cool down before cleaning. Wash by hand using a mild solution of warm water and liquid dish soap.
Cleaning and care ^ Clean all the parts with a mild solution of warm water and liquid dish soap. If necessary a small soft brush can be used to remove stubborn soiling. ^ Rinse all parts carefully and completely with water. ^ Dry parts with a soft cloth. Reassemble the cappuccinatore in the reverse order: ^ First replace the locking disc, followed by the dial on the cappuccinatore. ^ Then replace the milk tube and nozzles. ^ Fit the cappuccinatore on to the steam and water spout from below.
Cleaning and care Drip tray cover ^ Remove the cover from the drip tray. ^ The cover can be cleaned in the dishwasher or with a mild solution of warm water and liquid dish soap. ^ Dry with a soft cloth. Drip tray and waste container Clean the drip tray and waste container everyday. The waste container is located in the drip tray. The coffee system will display a message when the drip tray and/or waster container is full and needs to be emptied. This should be done when the message appears, if not sooner.
Cleaning and care Drip tray Waste container ^ Push the coffee dispensers up as far as they will go. The waste container will usually contain some residual water from the rinsing process. ^ Push the coffee dispensers up as far as they will go. ^ Remove the drip tray together with the waste container by pulling the drip tray forward. ^ Empty the waste container and the drip tray, if necessary. ^ Remove the drip tray together with the waste container by pulling the drip tray forward.
Cleaning and care Coffee bean container Disconnect the coffee system from the electrical supply before cleaning. ^ Open the lid on the right hand side of the coffee system. Remove the coffee bean container lid. ^ Remove any coffee beans. ^ Clean the bean container with a soft dry cloth. ^ Refill it with whole roasted espresso or coffee beans. ^ Replace the coffee bean container lid. If necessary, clean the ground coffee chute. ^ Open the lid of the ground coffee chute. ^ Remove any ground coffee.
Cleaning and care Do not move the brew unit handle, this could cause the brew unit to be out of alignment and you would be unable to fully push it back into the machine. To replace the brew unit, repeat the previous steps in the reverse order: ^ Push the brew unit back into the coffee system, making sure it is straight. Clean the brew unit by hand under warm water without soap. ^ Wipe away any coffee from the two filters. One filter is located in the funnel a, the other is to the left of the funnel b.
Cleaning and care TIP Place a suitable container under the coffee dispensers, so that you do not have to continually empty the drip tray. Cleaning/Degreasing the brew unit Depending on the fat content of the coffee, the brew unit can clog. Clean the brew unit approx. every 200 cups with the enclosed detergent tablets. They are specially developed for the coffee maker to optimize the degreasing. The cleaning tablets can be purchased from Miele.
Cleaning and care Exterior Remove any soiling as soon as possible. If not removed right away the surface of the machine could alter or discolor. Be sure water does not get behind the display. The exterior surfaces are susceptible to scratching. Contact with unsuitable cleaning agents could cause discoloration. Clean any descaling agent splashes immediately. ^ Turn the machine off using the button. ^ Clean the exterior with a soft, damp cloth and a mild solution of warm water and liquid dish soap.
Descaling Due to lime scale buildup the coffee system must be descaled regularly. How often, depends on the hardness of your local water supply. If the coffee system is hot, it will need to cool down for approx. 10 minutes before the descaling program can begin. The coffee system will remind you when a descaling program is needed. NO. PORTIONS UNTIL DESCALING: 50 will appear in the display. This number will then count down after each drink is prepared.
Descaling ^ Replace the water container in the coffee system. Selecting Descale via the MAINTENANCE menu When FILL WATER CONTAINER AND PLACE IN MACHINE appears in this display: ^ In the main menu press and hold the OK button for two seconds. ^ remove the water tank and rinse it carefully with clean water. Be sure that no descaling agent is left in the water container. Fill the water container with cold, clean tap water up to the "Max." mark.
Energy saving mode Eco-Mode Turning off When using Eco Mode the coffee system will save energy. If the machine will not be used for an extended period of time, turn it off using the main switch at the back of the machine. The coffee system will switch to Eco mode if it has not been used to prepare a drink in some time. When in Eco mode the heat function is not on constantly, therefore reducing energy usage. The coffee system will heat up again when a drink is selected.
Transport If the coffee machine will not be used for an extended period of time, e.g. vacation, or will be transported over a long distance, the machine should be prepared in the following ways: – Empty and clean the coffee bean container The evaporation process starts, the coffee system heats up and DRAIN THE SYSTEM appears in the display. The evaporation process is complete when the message goes out. Caution! Hot steam will escape from the cappuccinatore, de careful of burns.
Frequently Asked Questions ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Do not open the outer casing of the coffee system. Fault messages appear in the display Fault - 1, Fault - 80 or Fault - 82 The coffee machine has overheated ^ Turn the machine off with the On/Off button. Wait approx. one hour and then turn it on again.
Frequently Asked Questions EMPTY THE DRIP TRAY appears in the display even though the drip tray is empty The drip tray is not seated correctly. ^ Push the drip tray into the coffee system into it clicks into place. The metal contacts are dirty. ^ Clean and dry the contacts. or ^ The drip tray sensor is not working correctly. ^ Turn the coffee system off and then on again using the main switch. If the fault still appears, contact Miele Technical Service.
Frequently Asked Questions FILL WATER CONTAINER AND PLACE IN THE MACHINE appears in the display even though the water tank is full The water tank is not seated correctly. ^ Remove the water tank and then place it back into the niche. If the fault message still appears ^ empty the water container. ^ Check to see that the float moves freely, by shaking the water tank. ^ Fill the water container with fresh, cold tap water and replace it in the coffee system.
Frequently Asked Questions Preparation / dispensing problems Water is dispensed from the coffee dispensers when coffee has been selected ^ If ground coffee has not been added to the The ground coffee chute lid ground coffee chute, NO must be selected was opened and closed when prompted to use GROUND COFFEE. without coffee being put into it. YES was then selected when the GROUND COFFEE option appeared in the display.
Frequently Asked Questions The coffee or espresso is not hot enough The cup has not been pre-heated. ^ Pre-heat the cups (see "Pre-warming cups"). The brewing temperature is set too low. ^ Set a higher brew temperature (see "Brewing temperature"). The brew unit filters are blocked. ^ Clean the brew unit. ^ Clean/degrease the brew unit. See "Cleaning and care". The crema on the coffee or espresso is "not right" The grinder is not set correctly.
Frequently Asked Questions General problems When a drink is selected very little or nothing at all is dispensed from the coffee dispensers. The brew unit filters are blocked. ^ Clean/degrease the brew unit. See "Cleaning and care". Water has stopped flowing when programming the amount. The maximum amount possible was reached. Preparation is stopped and the max. portion size possible is saved. There is not enough water in the ^ Fill the water tank with fresh, cold tap water and replace it in the niche.
Frequently Asked Questions When the coffee system is turned on using the - button the display remains dark. The unit has no power. ^ The main switch is turned off. ^ The machine is not plugged in. ^ Check that the fuse had not blown or is defective. If the fuse has blown contact Miele's Technical Service Department. The coffee system turns off suddenly. The programmed turn off time has been reached. ^ If desired set a new turn off time (see "Timer"). The machine is not plugged in. ^ Check the plug.
Frequently Asked Questions The grinder is louder than usual There could be pebbles within the coffee beans. ^ Turn off the unit immediately. The coffee bean container has become empty during the grinding process. ^ Fill with fresh beans. ^ Contact Technical Service. The brew unit cannot be removed, or the brew unit cannot be replaced in the coffee system. The brew unit or the brew unit motor is not in the correct position. ^ Turn the machine off with the - button. ^ Press the .
Frequently Asked Questions The descaling program was started accidently. ^ Complete the descaling program (see The descaling program cannot "Descaling".) be canceled once the OK button has been pressed. This is a safety measure to ensure that the machine is fully descaled. It is important for the long-term protection of the machine and to ensure that it functions properly. Loud noises are heard during the descaling program. This is not a fault.
After sales service Repairs In the event of a fault which you cannot correct yourself please contact the Miele Service Department by phone number at the back of this booklet. ^ Please quote the model type and number of your appliance. These can be found on the data plate located behind the drip tray inside the coffee system.
Installation instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.
Caring for the environment Disposal of packing material Disposal of an old appliance The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Please recycle. Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
Electrical connection All electrical work should be performed by a qualified electrician in strict accordance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. Verify that the voltage, load and circuit rating information found on the data plate match the household electrical supply. This data must match to prevent damage to the coffee system. If in doubt, consult a licensed electrician.
Installation Danger of overheating! Ensure that there is sufficient ventilation around the coffee system. Be sure the vents at the top of the machine are not covered completely. Danger of overheating. If the coffee system is installed behind a cabinet door, it may only be used with the door open. Do not close the cabinet door while the coffee system is in use. – Install the coffee system in a dry, well ventilated room. – The ambient temperature should be between 50°F (10°C) and 90°F (32°C).
Dimensions 73
Alteration rights reserved / 2111 M.-Nr. 07 995 311 / 00 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
