Fitting and installation instructions Miele|home Con|ctivity XKM 2100 KM en - GB M.-Nr.
Contents Warning and safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Connecting the communication module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Con|ctivity. . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning and safety instructions This appliance complies with all relevant legal safety requirements. Improper use of the appliance can present a risk of both personal injury and material damage. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time. They contain important notes on its installation, safety, use and maintenance.
Warning and safety instructions ~ Installation, maintenance and repairs may only be carried out by a Miele authorised person in strict accordance with current national and local safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. Ensure that current is not supplied to the appliance until after maintenance or repair work has been carried out.
Electrical connection All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK). This appliance can be connected to the mains electricity supply either via a plug and switched socket or via a suitable fused spur connection unit. The socket and on-off switch should be easily accessible after the appliance has been built in.
Electrical connection To change the mains connection cable If the connection cable is damaged, it must be replaced by cable type H 05 V V-F (pvc insulated), available from the Miele Spare Parts Department. If the appliance is connected via a fused spur, the electrical cable must only be replaced by a suitable qualified electrician in accordance with local and national safety regulations. Connection data is quoted on the data plate.
Description of the appliance Miele|home connection box c b a a Shaft with communication module fitted b Data line c Connection point for mains connection cable 1 connection cable with plug 1 connection cable with wire end ferrules Accessories supplied: Adapter 7
Connecting the communication module Data line The connection point for the data line is located underneath the hob. The following illustrations are examples. The connection position may vary.
Connecting the communication module ,Data line types 1 and 2 must only be connected to the appliance by a qualified and competent electrician in strict accordance with current local and national safety regulations (BS 7671 in the UK). ^ Disconnect the hob from the electricity supply. ^ Remove the cover from the data line connection point (see illustration "Connecting the data line", Type 1 and Type 2). ^ Connect the data line. Use the adapter supplied for connection types 1 and 2.
Con|ctivity How the Con|ctivity system works Con|ctivity is the communication between the hob and the cooker hood. The operation of the cooker hood is automatically controlled by the operating status of the hob. For communication to take place, the cooker hood must be fitted with communication module XKM 2000 DA a and the hob must be fitted with communication module XKM 2100 KM b. The hob transmits information about its operating status to the cooker hood via the household power supply (Powerline) c.
Con|ctivity Establishing connection For communication to take place, the cooker hood and the hob have to be signed on. ^ Sign on the cooker hood (see "Fitting and installation instructions Con|ctivity XKM 2000 DA"). The process for signing on the cooker hood must be completed before the hob can be signed on. ^ Start the signing on process on the hob. Induction hob KM 59**: see "KM 59**" All other hobs: please refer to the "Con|ctivity / Miele|home" section in the operating instruction manual for your hob.
Con|ctivity Con|ctivity and Miele|home To install Con|ctivity and Miele|home for the first time ^ Select the correct installation option (see chart in "Miele|home / Installation options"). Carry out the first installation without signing on the cooker hood and the hob. ^ Sign on the cooker hood as an "Installation at a later date" appliance. ^ Sign on the hob as an "Installation at a later date" appliance (see chart in "Miele|home / Installation options").
Miele|home How the Miele|home system works Communication enabled appliances use the existing household power supply (Powerline communications) to transfer data to Miele|home master appliances (e.g. the InfoControl unit, the SuperVision appliance). You can use the master appliance to call up information about communication enabled appliances, such as programme status or fault messages at any time.
Miele|home Components Description Communication module – XKM 2000 SV This networks the master appliance with the communication enabled appliances and enables appliance data to be transferred through the household power supply. – XKM 2000 KF – XKM 2100 KM – XKM 2000 Communication enabled Information about this appliance can be called up appliance and data can also be recevied.
Miele|home Installation instructions and conditions required – A communication module must be fitted to each communication enabled appliance. – The appliance must be fitted with a communication module. – Appliances only need to be signed on to the Miele|home system once. – Appliances can be signed on during the First installation of the Miele|home system. – Appliances can be signed on at a later date to the master appliance, e.g. SuperVision appliance or InfoControl unit of an existing Miele|home system.
Miele|home Installation options Please make sure you know how to use your Miele|home enabled appliances and the InfoControl unit (if present) before you start. Please read the operating instructions supplied. Please also observe the Warning and Safety instructions contained in the operating instructions. The Communication module must be fitted to the Miele|home enabled appliances. Please read these installation instructions carefully and keep them in a safe place for reference.
Miele|home First installation a First installation of the InfoControl unit and signing on of the hob Switch the InfoControl unit on, select a language and set the time and the date (see the operating instructions supplied with the InfoControl unit). First installation Mieleqhome First installation Yes No ^ Select "Yes" by pressing the # button on the base station.
Miele|home First installation Mieleqhome Start signing on appliances Start the signing on process on the hob. Induction hob KM 59**: see "KM 59**" All other hobs: please refer to the "Con|ctivity / Miele|home" section in the operating instruction manual for your hob. During the signing on process, you will be asked to confirm the following on the InfoControl unit: After signing on all appliances Press the OK button ^ Press the # button on the InfoControl unit.
Miele|home First installation b First installation of the SuperVision appliance and signing on of the hob Before you can sign on the hob you will need to install the SuperVision appliance and start the signing on process (see the installation instructions for Miele|home). ^ Start the signing on process on the hob. Induction hob KM 59**: see "KM 59**" All other hobs: please refer to the "Con|ctivity / Miele|home" section in the operating instruction manual for your hob.
Miele|home First installation If signing on is successful, the SuperVision appliance display will show: Mieleqhome SuperVision Sign on successful ^ Confirm that signing on has been successful with "OK". ^ Confirm the signing on process on the hob. If the signing on process is unsuccessful, repeat the procedure. If this does not solve the problem, call the Miele Service Department.
Miele|home First installation c First installation of the InfoControl unit and SuperVision appliance, signing on of the hob Before you can sign on the hob you will need to switch on the SuperVision appliance and the InfoControl unit. Install Miele|home on the Info-Control unit (see the installation instructions for Miele|home). Start the signing on process on the hob.
Miele|home First installation All appliances received will be registered: – InfoControl display: Signing on Please wait O O O F F F F F FM – SuperVision appliance display: Mieleqhome SuperVision Signing on. Please wait O O O O F F F F F F F F FM If signing on is successful, – the SuperVision appliance display will show: Mieleqhome SuperVision Sign on successful ^ Confirm with "OK". – the InfoControl display will show: Sign on to Hob successful O O O O O O O O O Back A ~ Searching appliances Appl.
Miele|home Installation at a later date f Signing on the hob to the InfoControl unit at a later date ^ Press the 0 button on the mobile receiver to switch it on. ^ Press the # button on the base station for longer. The Menu will then open: Language F Time ... Searching Buzzer H ^ Select "Appliances" with the ) button and confirm your selection by pressing the # button. Back A Sign on appliances Appl.
Miele|home Installation at a later date The InfoControl unit will register the appliance: Signing on Please wait O O O F F F F F FM If signing on is successful, the InfoControl display will show: Sign on to Hob successful O O O O O O O O O Back A ~ Searching appliances Appl. search H ^ Select "Back" by pressing the # button. If you do not press the "#" button to confirm, the display will go out after 10 minutes. ^ Confirm the signing on process on the hob.
Miele|home Installation at a later date g Signing on the hob to the SuperVision appliance at a later date ^ Start the signing on process on the SuperVision appliance (see the installation instructions for Miele|home). ^ Start the signing on process on the hob. Induction hob KM 59**: see "KM 59**" All other hobs: please refer to the "Con|ctivity / Miele|home" section in the operating instruction manual for your hob.
Signing off the hob The signing off process must be carried out on the Miele|home master appliance and on the hob. Signing off ^ Switch on the Miele|home master appliance and start the signing off process (see the operating instructions for the relevant appliance). ^ Carry out the signing off process on the hob. Induction hob KM 59**: see "KM 59**" All other hobs: please refer to the "Con|ctivity / Miele|home" section in the operating instruction manual for your hob.
Signing on/off KM 59** hobs Signing on ^ With the hob switched off, touch the hob ON/OFF sensor s and the safety lock sensor $ at the same time until the indicator for the safety lock flashes. After the programming mode has been called up, P (Programme), S (Status) and numbers will appear in the cooking zone displays. These show the current settings.
Signing on/off KM 59** hobs Signing off ^ With the hob switched off, touch the hob ON/OFF sensor s and the safety lock sensor $ at the same time until the indicator for the safety lock flashes. After the programming mode has been called up, P (Programme), S (Status) and numbers will appear in the cooking zone displays. These show the current settings.
Problem solving guide The hob can only be signed on when the communication module is in the correct position. If the signing on process is unsuccessful, check first of all that the communication module is fitted correctly. If necessary, push the module into the slot until it clicks into position and then repeat the signing on procedure. Messages in the InfoControl mobile receiver display Message Cause Remedy Activation failed. There was a problem during activation.
Problem solving guide Problem Cause The signing on The appliance signing on procedure on the hob procedure has not been has been unsuccessful. started on the master appliance. Remedy ^ Repeat the signing on procedure on the master appliance and on the hob. There was a problem during the signing on procedure. ^ Repeat the signing on procedure. The signing off of the There was a problem hob was successful but during the signing off the hob still appears in procedure. the list of signed on appliances.
Alteration rights reserved / 3212 M.-Nr.