Operating and installation instructions Gas hobs CS 1012 CS 1034 To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en - GB M.-Nr.
D Das Gerät ist auch für den Gebrauch in anderen als auf dem Gerät angegebenen Bestimmungsländer zugelassen. Die landesspezifische Ausführung und die Anschlussart des Gerätes haben wesentlichen Einfluss auf den einwandfreien und sicheren Betrieb. Für den Betrieb in einem anderen als auf dem Gerät angegebenen Bestimmungsland wenden Sie sich bitte an den für das Land zuständigen Kundendienst. E El aparato está autorizado para el uso en países diferentes a los países de destino indicados.
Gas-heated appliances Safety precautions to take if you smell gas ß Turn off the gas emergency control valve immediately. This is usually located near the gas meter. ß Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. ß Do not operate electrical lights or switches, i.e. do not switch them "On" or "Off". ß Open all doors and windows to ventilate the area. ß If the smell of gas persists, evacuate the building.
Contents Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CS 1012 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CS 1034 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Warning and safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Caring for the environment .
Contents Preparing the worktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Installation of several appliances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Fitting the spring clamps and spacer bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Installing / removing the appliance(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 General installation tips . . . . . . . . . . . . . . . . . . . . . . .
Guide to the appliance CS 1012 a Extra large burner Controls: b Normal burner f rear c Pan support g front d Symbols to indicate which gas burner the control is for e Display Display l In-operation indicator m Residual heat indicator 6
Guide to the appliance CS 1034 a Large burner Controls: b Normal burner h front right c Extra large burner i rear right d Normal burner j rear left e Pan supports k front left f Symbols to indicate which gas burner the control is for g Display Display l In-operation indicator m Residual heat indicator 7
Guide to the appliance Burner n Burner cap o Burner head p Ignition safety device q Ignitor r Burner base 8
Warning and safety instructions Correct application This appliance complies with all relevant local and national safety requirements. Improper use can, however, present a risk of both personal injury and material damage. ~ This gas hob is not designed for commercial use.
Warning and safety instructions Safety with children ~ This appliance is only intended for use by adults who have read these instructions. This appliance is not a toy! To avoid the risk of injury, keep children well away and do not allow them to play with it or use the controls. They will not understand the potential dangers posed by it. They should be supervised whenever you are working in the kitchen.
Warning and safety instructions Technical safety ~ Before installation, check the appliance for visible signs of damage. Under no circumstances should you use a damaged appliance. It could be dangerous. ~ The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations.
Warning and safety instructions ~ During installation, maintenance and repair work, the appliance must be connected from the gas supply and mains electricity supply. ~ While the appliance is under guarantee, repairs should only be undertaken by a service technician authorised by Miele. Otherwise the guarantee is invalidated. ~ Faulty components must only be replaced by genuine Miele original spare parts. The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used.
Warning and safety instructions Correct use ~ The appliance gets hot when in use and remains hot for quite a while after it has been switched off. Do not touch it whilst it could still be hot. ~ If a cooker hood is installed above the gas hob, ensure that the burners are always covered with a pan when in use. Otherwise flames could reach the cooker hood, parts of which could then be damaged or set on fire. ~ Do not leave the appliance unattended whilst it is being used.
Warning and safety instructions ~ Ensure that the flames from the burner do not spread out beyond the base and up the sides of the pan. ~ Unless the pan manufacturer states that you can do so, do not use pans with very thin bases on this hob, and never heat up empty pans as they could get damaged. This could also damage the appliance. ~ The pan support supplied must always be used. Pans must not be placed directly on the burner. ~ Do not store any inflammable objects near the gas hob.
Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation.
Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service" section of this booklet. Cleaning for the first time ^ Remove any protective foil and stickers. ^ Clean all removable parts of the burners with a solution of warm water and a little washing-up liquid applied with a soft sponge. Dry all parts thoroughly after cleaning and then reassemble the burners (see "Cleaning and care").
Operation Rapid ignition system The appliance is supplied with a rapid ignition system with the following features: – Rapid ignition without pressing und holding the control – Automatic re-ignition Should the flame be extinguished by a gust of air, the burner will re-ignite automatically. If re-ignition is unsuccessful, the gas supply will be cut off automatically (see "Safety cut-off").
Operation Switching on Regulating the flame The burners can be regulated at any level between the strongest and weakest flame. ^ To ignite the burner press the control knob down and turn it anti-clockwise to the large flame symbol. The ignitor will make a clicking sound and ignite the gas. Operating a control will automatically create a spark on every burner. This is quite normal and does not indicate a fault. If the burner does not ignite, turn the control to off "ß".
Operation In-operation indicator and Residual heat indicator When a gas burner is switched on, the relevant in-operation indicator lights up. Once it has reached a certain temperature, the residual heat indicator also lights up. The in-operation indicator goes out when the gas burner is switched off. The residual heat indicator remains on until the gas burner is cool enough to touch. Do not touch or place any heat sensitive objects on the gas hob while the residual heat indicator is still on.
Pans Burner Min. pan base diameter in cm Normal burner 10 Large burner 12 Extra large burner 14 Max. diameter at top of pan in cm Normal burner 22 Large burner 24 Extra large burner 24 – Select pans which are suitable for the burner they are to be used on. In general: use larger diameter pans on the large burners, and smaller diameter pans on the small burners. – Wide, shallow pans are preferable to tall, narrow ones. They will heat up faster.
Safety features Thermo-electric ignition Safety cut-out This appliance has a thermo-electric ignition safety device. If the flame goes out, for example if food has boiled over or if there is a sudden draught, and automatic re-ignition has been unsuccessful, the supply of gas to the burner will be cut off. If a burner has been used for an unusually long period (approx. 4 hours), it will switch off automatically.
Cleaning and care General notes ,Under no circumstances use a steam cleaning appliance to clean this appliance. The steam could reach the electrical components and cause a short circuit. The appliance should be cleaned after each use. Let it cool down to room temperature. To avoid water marks and limescale deposits use a soft cloth to dry surfaces that have been cleaned with water.
Cleaning and care Stainless steel surfaces Pan supports, control knobs Clean stainless steel surfaces using an E-Cloth or with a solution of warm water and a little washing-up liquid applied with a soft sponge. In the case of stubborn dried-on soiling, soak first. Finally, dry with a soft cloth. Remove the pan supports. Clean the pan supports and the control knobs with a solution of warm water and a little washing-up liquid applied with a soft sponge. Stubborn soiling should be soaked first.
Cleaning and care Burner Reassemble the burner Do not clean any parts of the burner in a dishwasher. The burner should be dismantled and then cleaned by hand using a solution of warm water and a little washing-up liquid applied with a soft sponge. Parts of the burner that cannot be removed should be wiped clean with a damp cloth only. The ignitor and ignition safety device should be very carefully wiped clean using a well wrung out cloth. Do not let the ignitor get wet. If it gets wet it will not spark.
Problem solving guide ,Repairs to the gas and electrical components of this appliance must only be carried out by a suitably qualified and competent person to ensure safety (Gas Safe registered in the UK). Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. What to do if ... ... the burner does not ignite when the hob is being used for the first time or after a long period of not being used.
Problem solving guide ... the gas flame suddenly looks different. Check whether the burner components are assembled correctly. ... the gas flame goes out during operation. Check whether the burner components are assembled correctly. .... the ignitor on the burner does not spark. Check whether – the mains fuse has tripped. If it has, contact a qualified electrician or the Miele Service Department. – food deposits have lodged themselves between the ignitor and the burner cap.
Optional accessories Miele branded cleaning and conditioning products are available for your appliance. These can be ordered via the internet on www.miele-shop.com or from the Miele Spare Parts Department (see back cover) or from your Miele dealer. Ceramic and stainless steel hob cleaner 250 ml Removes heavy soiling, limescale deposits and light discolouration Stainless steel conditioning agent 250 ml Removes water marks, flecks and finger prints. Helps keep the hob looking good for longer.
Safety instructions for installation This appliance must be installed and connected to services in accordance with local and national safety and building regulations. Fit wall units and extractor hood before fitting the hob to avoid damaging the surface. ~ The room in which the gas hob is installed must be at least 20 m3 in size with a door or window in it which can be opened to the outside air.
Safety instructions for installation Safety distance above the hob A minimum safety distance must be maintained between this appliance and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood, a minimum safety distance of at least 760 mm must be maintained. For any flammable objects, e.g. utensil rails, wall units etc.
Safety instructions for installation Safety distances to the sides of the hob Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear and a tall unit or wall at one side. On the other side, however, no unit or divider should stand higher than the hob (see illustrations). Due to the high temperatures radiated by the hob, it is essential that a minimum distance of 50 mm is maintained between the worktop cut-out and the back wall.
Safety instructions for installation Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e. g. wood) a minimum safety distance e of 50 mm must be maintained between the cut-out and the cladding. If the niche cladding is made from a non-combustible material (e. g.
Appliance and building-in dimensions CS 1012 a Spring clamps b Front c Building-in depth d Building-in depth for the mains connection box with mains connection cable, L = 2000 mm e Building-in depth for the gas connection R 1/2 - ISO 7-1 (DIN 2999) 32
Appliance and building-in dimensions CS 1034 a Spring clamps b Front c Building-in depth d Building-in depth for the mains connection box with mains connection cable, L = 2000 mm e Building-in depth for the gas connection R 1/2 - ISO 7-1 (DIN 2999) 33
Preparing the worktop ^ Seal the cut surfaces with a suitable heat-resistant sealant to avoid swelling caused by moisture. The materials used must be heat-resistant. If, during installation, you find that the seals on the corners of the frame are not flush with the worktop surface, the corner radius (ß R4) can be carefully scribed to fit. 34 CS 1034 If the appliance is not installed above an oven the clamps supplied can be used for securing it (see illustration).
Installation of several appliances When installing two or more appliances next to each other a spacer bar b must be used between each one. See “Fixing the spring clamps and spacer bars”. Worktop cut-out - two appliances Worktop cut-out - three appliances To calculate the cut-out width (D) required: Add up the widths of each appliance (e.g. width A + B + C etc.) and subtract 16 mm from this figure (i.e. 8 mm is taken off either end of the appliance run).
Installation of several appliances a Spring clamps b Spacer bars c Gap between spacer bar and worktop d Sealing strip The illustration shows a worktop cut-out with spring clamps a and spacer bars b for 3 appliances. An additional spacer bar is required for each additional appliance. The position for securing each additional spacer bar will depend on the width of appliance B (288 mm / 380 mm / 576 mm).
Fitting the spring clamps and spacer bars Wooden worktops Granite and marble worktops The screws are not required for granite or marble worktops. ^ Position the spring clamps supplied a and spacer bars b on the top edge of the cut-out in the positions marked. ^ Secure the spring clamps and spacer bars with the 3.5 x 25 mm screws supplied. ^ Position and secure the spring clamps a and spacer bars b using strong, double-sided adhesive tape c.
Fitting the spring clamps and spacer bars ^ Apply silicone to the side edges and the lower edges of the spring clamps a and the spacer bars b. ^ Then fill gap e between the spacer bars and the worktop with silicone from the tube supplied.
Installing / removing the appliance(s) Installing the appliance(s) ^ Feed the connection cable down through the cut-out. ^ Starting at the front, position the appliance in the worktop cut-out. ^ Using both hands, press down evenly on the sides of the appliance until it clicks into position. When doing this make sure that the seal under the appliance sits flush with the worktop on all sides. This is important to ensure an effective seal all round. Do not use sealant.
General installation tips Tiled worktop Do not use any sealant unless expressly instructed to do so. The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop. Do not use sealant between the frame of the top part of the appliance and the worktop. This could cause difficulties if the appliance ever needs to be taken out for servicing and possibly result in damage to the frame or the worktop.
Electrical connection All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current local and national safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. Ensure power is not supplied to the appliance until after installation or repair work has been carried out. The appliance must only be operated when built-in.
Electrical connection Important The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system, which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and regularly tested and where there is any doubt, the electrical wiring in the home should be tested by a qualified electrician.
Gas connection ,Connection to the gas supply, or conversion from one type of gas to another, should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations (e.g. Gas Safe registered in the UK). Every appliance should have its own easily accessible isolating valve and test point.
Gas connection Connection The gas connection must be installed so that connection can be made either from inside or outside the kitchen unit, and the isolating valve must be easily accessible and visible (by opening one of the kitchen doors, if necessary). After installing the appliance the gas burners have to be set for local conditions.
Conversion to another type of gas ,Connection to the gas supply, or conversion from one type of gas to another, should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations (e.g. Gas Safe registered in the UK). When converting to a different type of gas, the main burner jets and the small burner jets have to be changed.
Conversion to another type of gas CS 1034 Screw in the new jets according to the following table. Nominal rating at high setting Gas type kW Normal burner Natural gas H Liquid gas 1.60 1.60 / 116 g/h Large burner Natural gas H Liquid gas 2.50 2.10 / 153 g/h Extra large Natural gas H burner Liquid gas 3.00 2.50 / 182 g/h Total output 8.70 7.80 / 568 g/h Natural gas H Liquid gas Nominal rating at low setting Gas type kW Normal burner Natural gas H Liquid gas 0.25 0.
Conversion to another type of gas Changing the jets Disconnect the gas hob from the mains electricity supply. Turn off the gas supply. To change the main jets ^ Carefully remove the upper section of the appliance. When doing this make sure you do not also pull out the light unit for the display a located underneath the upper section. To release the unit, squeeze together the two clamps b. ^ Remove the pan support, burner cap n and burner head o. ^ Using an M7 socket spanner, unscrew main jet s.
Conversion to another type of gas Function test Check all gas fittings for leaks. ^ Reassemble the appliance. ^ Check the burner flame by operating the burner. The flame must not go out on the lowest setting, or when the control is turned quickly from a high to a low setting. On the highest setting, the flame must have a distinctive and visible core. ^ Stick the label supplied with the jets above the label stating the type of gas being used.
After sales service, data plate In the event of any faults which you cannot remedy yourself, or if the appliance is under guarantee, please contact: – Your Miele dealer, or – the Miele Customer Contact Centre (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service. When contacting Miele, please quote the model and serial number of your appliance which are given on the data plate. N.B.
Alteration rights reserved/ 1610 M.-Nr.
