Installation Instructions CS1326 Y en - CA Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions.
IMPORTANT SAFETY INSTRUCTIONS Correct usage WARNING- When using your appliance follow basic precautions, including the following: Read all instructions before installation or use to prevent injury and appliance damage. This appliance conforms to all uniform safety codes and regulations. The manufacturer cannot be held responsible for damage or injury caused by improper use of this appliance. ~ Only use the Tepan Yaki for residential cooking, and for the purposes described in this manual.
IMPORTANT SAFETY INSTRUCTIONS Technical Safety ~ Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ Before installing the Tepan Yaki, check for externally visible damage. Do not operate a damaged appliance. ~ To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system.
IMPORTANT SAFETY INSTRUCTIONS Safety ~ The appliance is hot during use and remains so for some time after being switched off. Be careful not to touch the appliance if it may still be hot. ~ Protect your hands with oven mitts or potholders when using the appliance. Use only dry, heat resistant potholders. Moist or damp potholders used on hot surfaces can result in steam burns. Do not let the potholder touch the hot heating elements. Do not use towels or other bulky items near the appliance.
SAFETY INSTRUCTIONS FOR INSTALLATION Note to the installer: Please leave this instruction book with the consumer for the local electrical inspector’s use. ~ This appliance has not been designed for maritime use or for use in mobile installations such as recreational vehicles or aircraft. However, under certain conditions it may be possible for installation in these applications. Please contact the Miele Technical Service Department with specific requirements.
SAFETY INSTRUCTIONS FOR INSTALLATION Safety distances above the appliance If there is more than one appliance beneath a hood (e.g. wok burner and electric cooktop), and they have different minimum safety distances always observe the greater distance. The minimum safety distance given by the hood manufacturer must be maintained between the cooktop and the hood above it. See the installation instructions of the hood for these safety measurements.
SAFETY INSTRUCTIONS FOR INSTALLATION Safety distances to the sides of the appliance The appliance should only be installed as shown in the illustrations, while maintaining the required safety distances shown. Do not install the appliance between two tall cabinets, this is a fire hazard. A distance of alteast 2" (50 mm) must be kept between the countertop cut-out and the rear wall because of the high temperatures radiated.
Installation Safety distance when installing the appliance near a wall with trim or a back splash A minimum distance of 2" (50 mm) between the trim or back splash and the countertop cut-out if required. This distance is only necessary if these items are made of combustible materials e.g. wood. If the trim or back splash is made of a non-combustible material, the required safety distance can be reduced by the thickness of the wall covering material.
Installation Installation dimensions a Spring clips b Appliance front c Installation height d Power supply box with connection cable, L = 78 3/4" (2000 mm) 20
Installation Cut out ^ Make the worktop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the appliance(s). See also "SAFETY INSTRUCTIONS FOR INSTALLATION". If during installation the seal around the frame does not sit flush with the countertop in the corners, the corner radius, maximum 3/16" (4 mm), can be carefully filed down to fit.
Installation Installation of multiple appliances When installing more than one combiset appliance, a support bar b must be installed between the appliances. Countertop cut-out two appliances D Countertop cut-out three appliances (5 19 11 00 + /1 6" -1 m m b ) D (5 -1 b C A For the installation of two appliances the width of the countertop cut-out D is the sum of A and C.
Installation Sample calculations for a countertop cut-out for three appliances A appliance width minus 5/16" (8 mm) B appliance width C appliance width minus 5/16" (8 mm) D Countertop cut-out 11" (280 mm) 11 5/16" (288 mm) 11" (280 mm) 33 3/8" (848 mm) 11" (280 mm) 15" (380 mm) 14 5/8" (372 mm) 40 5/8" (1032 mm) 11" (280 mm) 22 11/16" (576 mm) 22 3/8" (568 mm) 56 1/16" (1424 mm) 14 5/8" (372 mm) 11 5/16" (288 mm) 11" (280 mm) 37" (940 mm) 14 5/8" (372 mm) 15" (380 mm) 14 5/8" (372 mm)
Installation 3/16 (2 D 2" 3 m 1"-130mm) (50 5 2 ( 2" m) 0mm) (5 (50m 2"m) 2"m) /16" " 1"5--130mm) (50m a a a b c (5 19 1 00 1/1 + 6" -1 m m ) c a a a B C 3/8" 5/8"/ 22mm) 8 4 "/1 2/56 11(280/37 " 1/16 3/8" 221m) / " 5/8" / 22m) 5 " 6 1 m / 14 68m 11 5/1 8//380/576 11"280/372/5 8 2 ( ( A a Spring clips b Support bars c Space between support bar and countertop An additional support bar is required for each additional appliance.
Installation Attach the spring clips and support bars Wood or solid surface countertops Granite countertop " " 1"-1 3/16 1"-1 ) 0mm ) 0mm (25-3 3/16 (25-3 a b ^ Place the supplied spring clips a and the support bars b at the marked positions as shown above, by laying them on the upper edge of the cut-out and then securing them with the 1/8" x 1" (3.5 x 25 mm) screws (supplied). c a c b ^ Position and attach the spring clips a and support bars b with strong, double-sided tape c.
Installation a ^ Coat the edges of the spring clips a, d b ^ and the space d between the strips b and the countertop with silicone (supplied).
Installation Installing the appliance ^ Feed the power cord down through the cut-out. ^ Then place the front side of the appliance in the countertop cut-out. ^ Then with a hand on each side of the appliance press down evenly on the edges until it clicks into position. When doing so make sure that the appliance seal sits tightly on the countertop to ensure it is sealed correctly. Do not permanently seal into the countertop. ^ Connect the appliance to the main power supply.
Installation Sealing Tiled surfaces The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. The grouting a and shaded area under the appliance frame must be flat and even, so that the frame will lie evenly and the sealing strip under the edge of the upper part of the appliance can provide an adequate seal against the countertop.
Electrical connection ,CAUTION: Before installation or servicing, disconnect the power supply by either removing the fuse, shutting off the main power supply or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer will not be held responsible.
Alteration rights reserved / 4608 For the most updated manual see the Miele web site. M.-Nr.
