Specs

ManualsBrandsMiele ManualsGas CooktopsMiele 12" Natural Gas Stainless Steel Wok Burner

Product and Cut-out Dimensions Page 1 of 4

CS 1011 Wok Burner CombiSet

1011

Wok

Burner

CombiSet

Location Codes

1 – Spring clips

2 – Appliance front

3 – Installation height

4 – Power supply box with connection cable with plug, Length = 47 1/4" (1200 mm)

120 V, 60 Hz, 15 A fuse rating. Actual power consumption (during ignition only) is 25 W.

Ensure that the power outlet is accessible after installation

5 – ½” NPT Gas fitting. The combiset should be ordered for either natural gas or LP gas. For your convenience an AGA

or CGA approved flexible stainless steel gas hose (accordion type) may be used between the gas connection and

the Miele regulator

the Miele regulator.

6 – Rating label – Ensure that the electrical supply matches the rating. Adhere rating label sticker supplied with the

appliance into the manual.

Shipping weight 23 lbs (10.4 kg)

Shipping dimensions 23” (584 mm) L x 16” (406 mm) W x 8” (203 mm) H

Notes

Indoor use

The combiset must not be installed over a dishwasher, wine storag

e, refrigerator or freezer. Heat radiated by the

combiset may damage the appliances.

Deep fat fryers must not be installed directly next to a gas combiset. A minimum distance of 11 5/16” is required.

The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of

the appliance provides a sufficient seal for the countertop.

All installations must be done in accordance with local codes.

Drawing is not to scale Specification Sheets OJS

02212012

Summary of content (4 pages)

PAGE 1
Product and Cut-out Dimensions Page 1 of 4 CS 1011 Wok Burner CombiSet Location Codes 1 – Spring clips 2 – Appliance front 3 – Installation height 4 – Power supply box with connection cable with plug, Length = 47 1/4" (1200 mm) 120 V, 60 Hz, 15 A fuse rating. Actual power consumption (during ignition only) is 25 W. Ensure that the power outlet is accessible after installation 5 – ½” NPT Gas fitting. The combiset should be ordered for either natural gas or LP gas.
PAGE 2
Product and Cut-out Dimensions Page 2 of 4 CS 1011 Wok Burner CombiSet Cut-out Dimensions For two CombiSet Appliances Cut-out Dimensions For three CombiSet Appliances For the installation of two appliances the width of the countertop cut-out D is the sum of A and C. For the installation of three appliances the width of the countertop cut-out D is the sum of A and B and C.
PAGE 3
Product and Cut-out Dimensions Page 3 of 4 CS 1011 Wok Burner CombiSet The illustration above represents p the attachment of spring p g clips p 1 and support pp bars 2 for 3 appliances An additional support bar is required for each additional appliance. The position for the attachment of an additional support bar depends on the width of appliance B.
PAGE 4
Product and Cut-out Dimensions Page 4 of 4 CS 1011 Wok Burner CombiSet Safety distances to back wall 1 – Wall frame 2 – Wall covering x = thickness of the wall covering 3 – Countertop p cut-out 4 – Countertop 5 – Minimum safety distance with flammable materials 2" (50 mm) with non-flammable materials 2" (50 mm) minus x If a wall covering is installed, a minimum safety distance must be maintained between the countertop cut-out and the covering, since high temperatures can damage these materials.