Operating and Installation Instructions Coffee System CVA 4062 CVA 4068 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the coffee system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Included accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 First steps to use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Touch controls . . . . . . . . . . . . . . . . . . . . .
Contents Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Tone options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Showroom program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Restoring factory default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances basic safety precautions should always be followed, including the following: Read all instructions before installation or use of the coffee system. Proper use Please read these instructions carefully to prevent accidents and machine damage. This appliance complies with current safety requirements. Improper use of the appliance can cause personal injury and material damage.
IMPORTANT SAFETY INSTRUCTIONS Technical safety ~ Before installing the appliance, check for externally visible damage. Do not operate a damaged appliance. ~ Before connecting the appliance to the electrical supply make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. If in doubt, consult a qualified technician. ~ Be certain your appliance is properly installed and grounded by a qualified technician.
IMPORTANT SAFETY INSTRUCTIONS ~ Do not let the cord hang over the edge of a table or counter, or touch hot surfaces. ~ Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner. Contact Miele. ~ Always attach the cord to the appliance first, then plug it into the wall outlet. To disconnect, turn the machine off, then remove the plug from the wall outlet. ~ Never open the outer casing of the appliance.
IMPORTANT SAFETY INSTRUCTIONS ~ Sugar can damage the appliance! Caramelized or otherwise pre-treated coffee beans or other sugar containing beverages must not be put in the machine. ~ The appliance must be descaled ~ Never place a cup with an alcohol-coffee mixture underneath the main dispenser. Plastic parts of the unit could catch fire! ~ Only use the descaling tablets ~ The hot water and steam dispensed could cause scalding. These functions must be used carefully.
Guide to the coffee system Front view a On/Off s touch control b Display c Left arrow <, to scroll through program options d OK touch control, to confirm selected program options and save settings e Right arrow >, to scroll through program options f Hot water - touch control g Door grip h Hot water dispenser i Lighting j Drip tray k Main dispenser, height-adjustable l Stainless-steel milk container 8
Guide to the coffee system Interior view a Main switch b Storage drawer c Funnel for ground coffee d Grind control slide e Coffee bean container f Drip tray with no-spill grid for transport g Water tank h Brew unit i Waste unit j Main dispenser connector (connects the brew unit to the main dispenser) k Stainless-steel milk container l Main dispenser connector cap 9
Guide to the coffee system Included accessories Cleaning agent Stainless steel milk container For daily cleaning of the milk pipework Cleaning tablets To hold and insulate milk, with lid/handle and additional cover for storing milk in the refrigerator (not dishwasher-safe) Cleaning containers To clean the brew unit Descaling tablets To descale the coffee system Large and small, for rinsing and cleaning the milk pipework Coffee spoon To measure ground coffee 10 Additional accessories are available.
First steps to use Touch controls Before the first use Select a touch control with your fingertip to use the machine. The appliance must be correctly installed and connected before the first use. See the "Installation Instructions" section of this manual.
First steps to use You will then be prompted to set the Time format. ^ Tap < or > until the time format you wish to select (12-hour or 24-hour) is highlighted, confirm with OK. ^ Enter the Time of day: First set the hours using < or >, confirm with OK. Repeat to set the minutes. ^ Now specify when the time of day should be displayed: – On: The time will be displayed even when the machine is turned off. – On for 60 seconds: The time will be displayed for 60 seconds after the machine has been turned off.
Filling water, beans or ground coffee Before using the coffee system for the first time, clean the appliance. See "Cleaning and Care". Be sure to program the water hardness (see "Settings - Water hardness"). Filling the water tank ^ Pull the water tank out. The beans and the water quality is important for a good espresso or coffee. The water tank must be washed and filled with fresh cold drinking water before each day of use. The unit displays a reminder when turned on.
Filling water, beans or ground coffee Filling the bean container Only fill espresso or coffee beans in the beans container. Anything else including ground coffee - will damage the grinding unit. Caramelized or otherwise pre-treated beans or sugar containing beverages must not be filled into the appliance. It will damage the coffee system. Filling ground coffee A funnel for ground coffee is provided in case you would like to prepare a different coffee type, e.g. decaffeinated coffee.
Preparing drinks Clean the coffee system daily to prevent bacterial growth. All parts of the coffee system are dishwasher-safe except for the brew unit, bean container, stainless-steel milk container and lid, and main dispenser cover. Failure to properly maintain machine may cause health issues. See "Cleaning and Care". The lines should be rinsed daily before the first use. This will happen automatically if the rinsing feature is set to "On" (see "Settings - Rinse Automatic") and the machine is cold.
Preparing drinks Adjusting main dispenser height The height of the main dispenser can be adjusted, to keep the shortest distance to the cup and retain heat, and maintain a better crema and froth. Espresso q r H I J L n m C ^ Use the arrow buttons to select the desired beverage, confirm by tapping OK once. The machine grinds the beans and pre-brews the coffee (if "On" is selected under "Pre-brewing"). The selected beverage is dispensed. ^ Slowly pull the main dispenser up or down as desired.
Preparing drinks Double portion If you would like a double portion of coffee or espresso, or to prepare two portions at the same time, ^ tap the OK button a second time, while the display reads "2 portions?". The two portions are always prepared one after the other.
Preparing drinks Prepare beverages Beverages with milk ^ Place a cup under the main spout. Stainless steel milk container ^ Tap the OK button. The appliance brews the espresso or coffee, and the selected beverage is dispensed from the main spout. Do not open the appliance door during the brewing process. The appliance will be damaged. After dispensing, the appliance automatically reverts to bean operation. The stainless steel milk container is vacuum insulated, to keep milk cold for a period of time.
Preparing drinks To prepare beverages with milk, Cappuccino, latte macchiato, hot milk, froth ^ Place a suitable cup or glass under both dispensers. ^ place the lid on the stainless steel milk container and turn the lid to the left, so that it clicks into place. For best results when preparing a latte macchiato, place the glass under the spout in such a way that the espresso flows into the middle of the froth.
Preparing drinks User profile beverages After use The user profile function is used to prepare beverages to suit your taste, by adjusting the amounts of water, milk, and ground coffee, as well as temperature and pre-brewing (see "Creating a user profile"). If you have already created a user profile, first select it then prepare the beverage. User profile q r H I J L n m C ^ Tap < or > until "User profile" is highlighted, confirm with OK. ^ Tap < or > to select "Select", confirm with OK.
Adjusting the coffee grinder The finer the coffee beans are ground determines the strength of the coffee and the quality of the crema. To prevent machine damage adjust the coffee grinder one level at a time and let the beans grind before adjusting another notch. Otherwise the machine will be damaged. The grinder should be adjusted: – If the espresso flows too quickly into the cup, the pressure cannot be built up because the beans have been ground too coarsely.
Settings The coffee system can be customized to suit individual preferences. Settings menu r H I J L You can select the language for all text and messages displayed on your machine. ^ Select "Settings F" and confirm with OK. Settings F q Language n m C ^ Tap < or > until Settings C is highlighted. Confirm with OK. ^ Tap < or > until the desired option is highlighted and confirm with OK. The current setting(s) will be marked with a check.
Settings Time of day Clock format ^ Select "Settings F", confirm with OK. ^ Use < or > to select "Clock format". Settings Time of day Timer ^ Tap < or > until "Time of day" is highlighted, confirm with OK. ^ Tap < or > to select a 24-hour or 12-hour display. ^ While the desired option is highlighted, confirm with OK. The clock format is now saved. Three options are now available: Setting the time of day Display ^ Use < or > to select "Set". The time display can be turned on or off.
Settings Timer Switch off after ^ Select "Settings F", confirm with OK ^ Select < or > until "Timer" is highlighted, confirm with OK. The machine will turn off automatically to save energy after a programmed period of time (ranging from 15 minutes to 9 hours after the last use). When the "Switch off after" option is set, the machine will turn off automatically after the programmed amount of time. ^ Use < or > to select "Set", confirm with OK. ^ Use < or > to select "Switch off after", confirm with OK.
Settings Switch off at A specific time of day can be set to turn the coffee system off. ^ Use < or > to select "Switch off at", confirm with OK. ^ Tap < or > to set the hours. Confirm with OK. Repeat to set the minutes. The machine will turn on each day at the specified time when you have activated the timer (see "Activate"). Coffee jug (dispensing several servings, one directly after another) With this function, you can dispense up to eight servings of coffee, one immediately after another (max.
Settings Amount of coffee Pre-brewing The amount of coffee will determine both the strength and the crema of your brewed coffee. During the pre-brew step, the freshly ground coffee is first moistened with hot water. After a short steeping period, the remaining water is then forced through the moistened coffee at high pressure. This process produces a much more intense coffee aroma. Depending on the type of coffee, the ideal amount ranges from approximately 0.2 ounces and 0.
Settings Temperature Automatic rinsing Five temperature settings are available for each coffee beverage and three settings for hot water. It is important to flush out any residual coffee from the lines when starting to use the machine for the day. If the automatic rinse function is activated and the machine is cold, the rinse cycle will begin automatically as soon as the machine is turned on. This will also pre-heat the lines with the hot water used during the rinse cycle.
Settings Steam system This appliance has two heating systems, making it possible for you to prepare milk froth/hot milk and coffee/espresso, one right after the other. If you seldom need milk froth or hot milk, you can turn the steam heating system off to save energy. If you select milk froth or hot milk with the steam heating system turned off, the machine must first heat up. The steam heating system will remain On until the machine has been turned off completely. ^ Select "Settings F", confirm with OK.
Settings Lighting: Setting the switch-off time Whenever the machine is On, the machine lighting is also On. The lighting turns off automatically when the machine has been idle for 15 minutes. When the machine is turned off, you can program the lighting to remain On and to then shut off automatically after a certain amount of time if the machine is not used You can choose a duration from 15 minutes to 6 hours. ^ Turn the machine Off. ^ With the machine turned off, tap OK.
Settings System lock Water hardness The coffee system can be locked so that it cannot be used by children or those not familiar with the operating instructions. The hardness of the water used in the coffee system must be determined and programmed into the appliance. The water hardness will determine how frequently the unit must be descaled to maintain the coffee system properly.
Settings You can program four hardness levels on the machine: – Level 1 (soft): 0 - 3 gr/gal (0 - 3 °d) – Level 2 (moderately hard): 4 - 7 gr/gal (4 - 7 °d) – Level 3 (hard): 7 - 15 gr/gal (7 - 14 °d) – Level 4 (very hard): 15 - 22 gr/gal (14 - 21 °d) ^ Select "Settings F", confirm with OK. Settings Water hardness Display ^ Tap < or > until "Water hardness" is highlighted, confirm with OK. Display The display contrast and brightness can be adjusted. ^ Select "Settings F" , confirm with OK.
Settings Tone options Showroom program A tone can be selected to confirm the selection of a touch control. The volume of the tone can also be adjusted. The showroom program is used to demonstrate the machine at exhibits. In this demo mode, the machine lighting is On, but the machine does not heat up. ^ Select "Settings F", confirm with OK. Settings Volume Showroom prog. ^ Tap < or > until "Volume" is highlighted, confirm with OK. ^ Tap < or > to select "Buzzer tones" or "Keypad tone", confirm with OK.
Settings Restoring factory default settings Factory default settings The "Factory default" setting can be used to reset different settings back to their original default status. – Temperatures for coffee beverages and hot water (medium for both) You can select whether to reset all settings to the factory default or delete any user profiles. ^ Select "Settings F", confirm with OK. Settings Factory default Back # ^ Tap < or > until "Factory default" is highlighted, confirm with OK.
Setting the serving sizes The flavor of a coffee beverage depends not only on the type of coffee, but also on the quantity of water used. Not every espresso or cappuccino cup is the same size. Use this feature to set the volume of water to suit your taste and cup sizes. Setting serving sizes of espresso, coffee, hot milk and milk froth using OK ^ Place the desired cup under the main dispensers. ^ Select the beverage type.
Setting the serving sizes Setting serving sizes for cappuccino and latte macchiato using OK ^ Place the cappuccino cup or latte macchiato glass you will be using to set the portion size under the main dispensers. ^ Select cappuccino or latte macchiato. ^ Press and hold OK until the display shows the options for Cappuccino (Milk froth, Espresso) or Latte Macchiato (Hot milk, Milk froth, Espresso). Latte Macchiato The appliance now begins preparing a cappuccino or latte macchiato.
Setting the serving sizes Setting the serving size for hot water Setting serving sizes via "Settings" ^ Place the desired cup under the hot water dispenser. ^ Select "Settings F", confirm with OK. ^ Tap - until the display reads "Prog. the amount". ^ Tap - again once the cup is filled as desired and "Save" appears in the display. Each time the hot water is prepared the programmed amount will be dispensed. Settings Prog. the amount Amount of coffee ^ Tap < or > until "Prog.
User profiles If the appliance is used by several people with different preferences, you can save up to 9 individual user profiles. The following settings can be programmed for each user profile: – Serving size for coffee beverages and hot water – Serving size of milk for beverages with milk – Amount of coffee – Water temperature User profile H I J – Delete user profile to delete a user profile.
User profiles Creating a user profile Saving an entry ^ Tap < or > until "Create" is highlighted, confirm with OK. ^ Once you have completed an entry, use < or > to select "OK", confirm with OK. Up to 9 user profiles can be created. If you try to create more than 9 user profiles, the message "Memory full" will appear, you will need to delete a profile to create space. The display will briefly show the User profile welcome screen, followed by the main menu.
User profiles Deleting a user profile Revert ^ Select "Delete user profile", confirm with OK. The appliance can be set so that it automatically reverts to the standard user profile or continues to use the most recently selected user profile set. ^ Use < or > to select the user profile you wish to delete, confirm with OK. A check mark appears after the user profile, and it will be erased shortly. ^ Use < or > to select "Revert".
Cleaning and care Quick Guide The coffee machine must be cleaned regularly to prevent bacteria.
Cleaning and care Rinsing the system Allow the coffee system to cool before cleaning. Danger of burns! Do not clean the unit with a steam cleaner. Never use cleaners containing chlorides, sand, soda or scouring agents. These will damage the surface. To avoid mold, growth and odors it is important to clean the machine regularly.
Cleaning and care Milk pipework Cleaning the milk pipework Rinsing the milk pipework To prevent the milk residue from spoiling or drying in the machine and pipework, you should rinse these lines after use. In addition to rinsing after use, the lines need to be cleaned at the end of the day. Maintenance q r H I J L n m To prevent milk residue from spoiling or drying in the machine and pipework, it should be cleaned at the end of each day milk was used to make a beverage.
Cleaning and care Cleaning clogged milk pipework If no milk, just steam, comes out of the main dispenser, the milk pipework in the appliance door may be clogged. ^ Take the lid off the main dispenser. Pull out the nozzles of the main dispenser (see "Main dispenser"). To rinse the pipework in the lid of the stainless-steel milk container, fill the large cleaning container to the "max." mark with lukewarm water to dissolve the cleaning agent.
Cleaning and care ^ Remove the cover with the milk pipework. Clean the whole part in the dishwasher without taking it apart. If there are milk residues in the milk pipework you can clean them with the cleaning brush provided. To do this, take the cover and the milk pipework apart as follows: Do not pull the milk hoses off the retainers. This may cause the milk pipework to leak. ^ Press the small recess on the dispenser retainer a and pull the retainer out towards the front b.
Cleaning and care Stainless-steel milk container The stainless-steel milk container and lid must be cleaned by hand with hot water. Make sure to keep the top and seals of the container clean. Soiling can affect the functioning of the milk container. ^ Then press the milk hoses into the guide rail a and push the dispenser retainer b on until it clicks into place. ^ Put the cover with the milk pipework back into the rear of the appliance door. ^ Reattach the main dispenser (see "Main dispenser").
Cleaning and care Main dispenser ^ Pull the main dispenser all the way down a and pull the cover forward to remove b. ^ Pull both rubber stoppers a out and clean the stoppers and nozzles thoroughly. ^ Pull the air intake pipe b out if necessary. You can knead or blow through the pipe to remove any potential blockages. Never use a sharp object to remove blockages, this could damage the parts. ^ Turn the cover around, slide the insert upward and out, and clean both parts thoroughly.
Cleaning and care Water tank Waste unit Empty the water tank daily and refill before preparing the first drink with fresh, cold tap water. The display shows a message to empty the waste unit. Clean the waste unit daily. Coffee waste can mold if there is water in the waste unit from the rinse process. There may be water in the waste container from the rinsing process. This is normal. Check if the valve is clean. If the valve has residues on it, the water tank will not connect properly and might leak.
Cleaning and care Drip tray The trip tray contains a sensor which causes the display to show when the tray is full and needs to be emptied. Clean the drip tray daily. Remove the drip tray after the final rinse when no more water runs from the lines. Carefully remove the drip tray from the machine; the water may be very hot and could cause scalding. ^ Wash the drip tray and grid in the dishwasher or by hand with hot water and liquid dish soap, then dry with a soft cloth.
Cleaning and care Bean container The bean container must be cleaned by hand with hot water and liquid dish soap. Do not use a dishwasher. Interior and door ^ Once all movable parts are removed clean the interior with a solution of hot water and liquid dish soap. Dry ground coffee can be vacuumed. ^ Pull the bean container out and push the lid back. ^ Wash the bean container by hand with hot water and liquid dish soap, then dry with a soft cloth.
Cleaning and care Brew unit Manually clean the brew unit weekly. The movable parts are lubricated and the cap will get damaged in the dishwasher. Do not use a dishwasher this will cause damage. ^ Take out the water tank, waste unit and the storage drawer. ^ Rub off any coffee residue from the filters with a sponge. One filter is in the funnel, a, the second is to the left of the funnel, b. ^ Dry the funnel, a, to prevent ground coffee from sticking. ^ Clean the interior and remove coffee residues.
Cleaning and care Cleaning/Degreasing the brew unit Depending on the oil content of the coffee, the brew unit can clog. Clean the brew unit approx. every 200 cups with the enclosed detergent tablets. They are specially developed for the coffee maker to optimize the degreasing. The cleaning tablets can be purchased from Miele. As a reminder the display shows "Please run cleaning program" after 200 cups and then until the machine is cleaned. The cleaning process takes about 6 minutes.
Cleaning and care When the display prompts you to Please drop the cleaning tablet in the ground coffee funnel. Only use a slightly damp sponge when cleaning the controls. Water could penetrate into the electronics and cause damage. The external surfaces of the coffee machine are susceptible to scratching. Scratches on the glass surface could also weaken the glass making it more susceptible to breakages. ^ Remove the storage drawer and open the funnel lid. ^ Drop a cleaning tablet into the funnel.
Descaling the appliance The coffee system must be descaled regularly. The appliance will display a reminder message to descale and will eventually lock if not descaled. The display will show "Please descale the coffee system. Remaining number of servings: 50". This message will now appear after each preparation. ^ Tap OK to acknowledge this message. If the counter has elapsed to 0, the appliance will be locked, and the display reads: Descaling program must be carried out.
Descaling the appliance Descaling To dissolve the descaling tablets: Maintenance q r H I J L n m C ^ Tap < or > until "Maintenance m" is highlighted, confirm with OK. ^ Select "Descale" confirm with OK or, if the appliance is switched off: tap OK while switched off. ^ Select "Start", tap OK to begin the descaling process. The display prompts the user through the single steps of the descaling process. Follow the prompts.
Frequently asked questions ,Repairs to electrical appliances should only be carried out by a suitably qualified person in accordance with local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The light does not illuminate when the appliance is turned on. Possible fault Solution Is the lighting turned off? – See "Settings - Lighting". If not, the lighting is defective. Contact Miele. The display remains dark.
Frequently asked questions What if the machine does not switch on, even though the "Switch on at" timer setting is activated? Possible fault Solution The System Lock is activated. See "Settings - System Lock". The display messages are difficult to read. Possible fault Solution The contrast or brightness of the Adjust the display contrast / brightness. displays are too low / high. See "Settings - Display". Little or no coffee or espresso is dispensed from the main dispenser.
Frequently asked questions The display prompts me to fill or insert the stainless steel milk container even though the container has already been filled and inserted Possible fault Solution The container needs to be cleaned. See "Cleaning and Care". The grinding sounds louder than usual. Possible fault Solution There could be pebbles within the coffee beans. – Turn off the unit immediately. – Contact the Miele's Tech. Service if the bean container is not empty.
Frequently asked questions The coffee/espresso is not hot enough. Possible fault Solution – Were the supply lines and cup pre-heated? – The temperature is set too low. – The smaller the cup, the more important it is to pre-heat. – Check on what temperature range the coffee type is set. – Check if the brew unit is clogged. – Clean the brew unit. No drink is prepared although the beans were grinded and enough water is in the container.
Frequently asked questions Instead of coffee only water is dispensed. Possible fault Solution – The beans may have gotten stuck. – Pull the bean container out and push it back in. – The ground coffee funnel cover was opened and closed and a preparation with ground coffee was selected but no ground coffee was inserted. The coffee system switches automatically back to bean use after preparation. The drip tray is empty but a message to empty it is displayed.
Frequently asked questions Water is in the waste unit. Possible fault Solution This is not a fault. This is residual water from the cleaning process. "Coffee water" is in the waste unit. Possible fault Solution – If the grind setting is too coarse, this can result in too much coffee water in the waste unit. – The main dispenser cap is not positioned correctly. – Adjust the grind setting and/or amount of coffee. – Lubricate the cap with the supplied silicone grease.
Frequently asked questions The brew unit or waste unit could not be pulled from the machine. Possible fault Solution – The brew unit is not in the correct position. – The door was opened during grinding or brewing. – Close the door. The brew unit automatically gets into the correct position. No crema has formed or it is "different". Possible fault Solution – Check if the grind setting is too coarse or too fine. – Check what temperature range the coffee type is set.
Frequently asked questions Too much crema has formed and is above the coffee dispensers. Possible fault Solution Some coffee types produce too much Lower the temperature and amount of crema when the coffee / espresso coffee. temperature is set to the maximum and the amount of ground coffee is too much. The main dispenser cap is faulty (see, "Guide to the machine - Interior view"). Possible fault Solution Replace the cap with the spare part supplied.
Frequently asked questions The message "Check brew unit" appears on the display? Possible fault Solution The brew unit is clogged. – Follow the display prompts. – Clean the brew unit (see "Cleaning and care" - "Brew unit"). – Set the amount of ground coffee and the grinder setting to the medium settings, also adjust these settings in the user profiles. See the respective chapters in this manual.
Frequently asked questions The message "Fault - 73" appears in the display. Possible fault Solution The brew unit cannot reset to the correct position. – Take out and clean the brew unit. See "Cleaning and Care - Brew unit". – Push the coffee ejector of the brew unit into the correct position. – Set the brew unit aside and insert the waste unit and the water tank. – Close the door. The brew unit motor will automatically move to the correct position.
After sales service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the contact information on the back of this booklet. When contacting the Technical Service Department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
Installation instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.
Caring for the environment Disposal of packing material Disposal of an old appliance The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Please recycle. Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
Electrical connection Make sure that the power to the machine is OFF before installing or performing maintenance or repairs. WARNING: THIS APPLIANCE MUST BE GROUNDED Important All electrical work should be performed by a qualified electrician in strict accordance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. The coffee system comes equipped with a 6 ft (1.
Installation Installation options The coffee system is designed to be built into cabinetry. Miele appliances can be installed flush or proud. Discuss your installation requirements with your architect, designer and installer. A combination with other Miele built in appliances is possible. If the machine is installed in combination with other appliances, it should be installed with a protective base between the appliance and the unit (exception: installation with a built-in plate warmer).
Installation Installation Make sure power is not supplied to the appliance while installation or maintenance work is performed. Disconnect the power supply to the work area by unplugging the unit, tripping the circuit breaker or removing the fuse. The coffee system must be installed into cabinetry before being used. This unit should only be used in room temperatures ranging between 59 °F and 140 °F.
Installation Adjusting the door hinges The door hinges can be adjusted if the door cannot be opened easily. ^ Push the appliance into the niche. ^ Open the door and partially tighten the screws. ^ Carefully turn the lower screws, a, to center the machine. ^ To secure the appliance in the cabinet, tighten the upper screws, b, by hand. Do not use an electric screwdriver. 72 ^ To adjust the door sideways, a, turn screw a. ^ To adjust the door to the front or back, b, turn screw b.
Alteration rights reserved / 0811 M.-Nr. 07 816 880 / 02 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.