Operating and Installation Instructions Built-in Coffee System To prevent accidents and machine damage, you must read these instructions before installation or use. en-US M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS ............................................................ 5 Preparing your appliance for an extended vacation....................................... 13 Guide to the appliance ..................................................................................... 16 Controls and indicators .................................................................................... 18 Operation.....................................................................................
Contents Pre-brewing ground coffee.................................................................................. 40 Profiles................................................................................................................ Creating a profile ................................................................................................. Changing drinks within a profile .......................................................................... Making drinks stored in a profile ............
Contents Clean by hand or in dishwasher .......................................................................... Unsuitable cleaning agents ................................................................................. Cleaning the drip tray and grounds container..................................................... Cleaning the drip-tray cover................................................................................ Cleaning the water container ....................................................
IMPORTANT SAFETY INSTRUCTIONS This coffee machine complies with all the stipulated safety requirements. Inappropriate use can, however, lead to personal injury and material damage. Read the operating instructions carefully before using the coffee machine. They contain important information on safety, installation, use, and maintenance. This prevents both personal injury and damage to the coffee machine.
IMPORTANT SAFETY INSTRUCTIONS Appropriate use This coffee machine is intended for household use. Do not use the coffee machine outdoors. This coffee machine must not be used at altitudes above 6560 ft (2000 m). The machine is intended only for household use and for the preparation of drinks such as espresso, cappuccino, latte macchiato, tea, etc. All other types of use are not permitted.
IMPORTANT SAFETY INSTRUCTIONS Safety with children Danger of burning and scalding at the dispensers. Children's skin is far more sensitive to high temperatures than that of adults. Ensure children do not touch hot surfaces of the coffee machine or place parts of their body under the dispensers. Keep the coffee system out of reach of children. Children must be kept away from the coffee machine unless they are constantly supervised.
IMPORTANT SAFETY INSTRUCTIONS Technical safety Installation work or repairs should only be carried out by a Miele authorized technician. Unauthorized or incorrect installation work or repairs can pose considerable danger to users. A damaged coffee system could be dangerous. Before building in the machine, check it for any externally visible damage. Do not use a damaged machine.
IMPORTANT SAFETY INSTRUCTIONS Ensure that the power cord will not be pinched or damaged by any sharp edges. To reduce the risk of injury, do not drape cord over the counter top or table top where it can be pulled on by children or tripped over unintentionally. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.
IMPORTANT SAFETY INSTRUCTIONS For repairs, the coffee system must be disconnected from the electrical power supply. The coffee system is only disconnected from the power supply if - the circuit breaker has been tripped, or - the fuse is removed, or - the power cord is disconnected from the power supply. Pull the plug, not the cord, to disconnect the appliance from the power supply.
IMPORTANT SAFETY INSTRUCTIONS Risk of injury to the eyes! Never look at the lighting directly or using optical instruments (e.g. magnifying glass). Please note the following regarding water: - The water quality must conform to the requirements for drinking water in the country in which the coffee machine is being used. - Only use cold, fresh tap water to fill the water container. Hot or warm water or other liquids can damage the coffee machine.
IMPORTANT SAFETY INSTRUCTIONS Do not swing from or hang anything on the machine front when it is open as this could damage the hinges of the machine. Do not use the coffee system to clean objects.
IMPORTANT SAFETY INSTRUCTIONS Preparing your appliance for an extended vacation If you elect to turn off the water to your home for an extended period of time, please note that this may not be enough to reduce the risk of a leak. To be completely safe, you must turn off the water supply to each individual appliance. This means under the sink for a dishwasher, at the laundry bib for your washer, etc.
IMPORTANT SAFETY INSTRUCTIONS Descale the coffee system regularly depending on the water hardness level in your area. Descale the machine more frequently in areas with very hard water. Miele cannot be held liable for damage arising from insufficient descaling, the use of incorrect descaling agent or the use of descaling agent that is not of the appropriate concentration. Degrease the brew unit regularly with Miele cleaning tablets.
IMPORTANT SAFETY INSTRUCTIONS For machines with stainless steel surfaces: Do not use sticky notes, transparent adhesive tape, masking tape, or other types of adhesive on the stainless steel surfaces. These will damage the stainless steel surfaces, causing them to lose their dirtrepellent protective coating. The finish on stainless steel surfaces is susceptible to scratching. Even magnets can cause scratching.
Guide to the appliance Front view 1 2 3 6 4 5 a On/Off button b Control panel c Door handle d Height-adjustable main dispenser with lighting e Drip-tray cover f Milk container 16
Guide to the appliance Interior view a Bean containers b Milk valve c Height-adjustable main dispenser with lighting d Grinder setting e Bean containers f Fan outlet g Water container h Drip tray with lid i Brew unit j Grounds container k Maintenance container l Drip tray 17
Controls and indicators 6 a On/Off button h OK sensor button For switching coffee machine on and For confirming display messages and off saving settings b Drink buttons For making drinks c Display For showing information about the current action or status d sensor button – For making other drinks, e.g., Ristretto, Capuccino italiano – For making a pot of tea or coffee – Settings menu e Profiles sensor button For creating and managing profiles f Maintenance sensor button Maintenance programs, e.
Controls and indicators Drink button symbols Espresso Coffee Long coffee Capuccino Latte macchiato Caffè latte Hot milk Milk froth Tea water 19
Operation Sensor buttons To operate the coffee machine, tap the sensor buttons with your finger. An audible signal is generated each time a button is tapped. You can adjust the volume of the signal tones or switch the tones off (see “Settings – Volume”). Drinks menu When the following appears in the display, you are in the drinks menu: Select drink. 12:00 Miele As soon as you reach a confirmable value, message, or setting, the OK sensor button will light up orange. Tap OK to confirm your selection.
Operation Entering a name Letters and numbers are entered via the navigation area. You can choose between upper and lower case letters. Tip: It is best to select short names. Name Z A B C D E F - To enter a character, highlight the one you want and confirm your choice with OK. - To delete a character, tap the sensor control. - To save the name, select the checkmark and confirm with OK.
Operation Symbols in the display The following symbols may also appear in the display in addition to the text: Symbol Explanation This symbol indicates the Settings menu and the Language menu option. This symbol indicates that there is additional information and advice about using the coffee machine. Select OK to confirm the information. This symbol appears if the system lock is activated. Operation is locked.
Before first use Miele@home Your coffee machine is equipped with an integrated WiFi module. To use this feature, you will need: - a WiFi network - the Miele app - a Miele user account You can create a user account via the Miele app. The Miele app will guide you through the process of connecting your coffee machine to your home WiFi network.
Before first use Before using for the first time Connect the coffee machine to the electricity supply. Install the coffee machine. Remove any notices from the machine. Remove the protective foil from the drip-tray cover. Clean the water container, bean containers, and the main dispenser. Remove the water container and fill it with fresh, cold tap water. Only fill the water container up to the “max.” mark and then reinsert it in the machine (see “Filling the water container”).
Before first use Selecting the Performance Mode You can select the appropriate mode to suit your personal preferences (see “Settings – Performance Mode”). - Eco Mode: This is an energy-saving mode. - Barista Mode: This mode has been optimized for unadulterated coffee enjoyment. - Latte Mode: In this mode, milkbased drinks can be prepared within a much shorter space of time. Select the desired mode and confirm with OK. Your machine has been successfully set up and is ready for use.
Filling the coffee bean container Coffee or espresso can be made from whole roasted coffee beans which are freshly ground for each cup. This requires the bean containers to be filled with coffee beans. Risk of damage to the grinder due to incorrect operation. The coffee machine will be damaged if the bean container is filled with unsuitable substances such as liquids, ground coffee, or coffee beans treated with sugar, caramel, or similar.
Filling the water tank Risk to health due to contaminated water. Bacteria can develop in water which has been sitting in the water container for too long and is a risk to your health. Change the water in the water container every day. Risk of damage due to incorrect operation. Unsuitable liquids such as hot or warm water or other liquids can damage the coffee machine. Carbonated water leaves too much limescale in the coffee machine. Only use cold, fresh tap water to fill the water container.
Switching on and off Switching the coffee machine on Tap the On/Off button . The coffee machine heats up and rinses the pipework. Hot water will run out of the main dispenser. You can now make drinks. If the coffee machine is already at operating temperature, rinsing will not take place when the appliance is switched on. While dispensing a drink or during maintenance processes, moisture builds up in the coffee machine.
Dispenser adjustment The main dispenser cannot be manually adjusted. Before making the drink, the main dispenser moves down and the cup sensor stops it at the optimum height for the cups or glasses being used. When the coffee machine is switched off, the main dispenser will be in the middle position. When a maintenance program is being carried out, the main dispenser will move to the height of the maintenance container or into a low maintenance position.
Preparing beverages Danger of burning and scalding at the dispensers. The liquids and steam dispensed are very hot and can cause scalding. Keep away from the area underneath the dispensers when hot liquids and steam are being dispensed. Do not touch hot components. Making coffee with and without milk The following drinks can be made: - Ristretto is a concentrated, stronger espresso. It is prepared with the same amount of coffee as for an espresso but with a lot less water.
Preparing beverages Milk preparation Milk or milk alternatives (e.g., soy milk) containing added sugar can clog up the milk pipe and the rest of the milk pipework. Residues from unsuitable liquids can interfere with milk preparation. The milk used must not contain any additives. Only use pasteurized cow's milk. Tip: Using cold cow's milk (< 50°F/10°C) with a protein content of at least 3% will produce the perfect milk froth. You can select milk with a fat content according to your personal preference.
Preparing beverages Making a coffee drink Push the milk flask back into the coffee machine until it clicks into place. Tip: It is easier to remove the milk flask with both hands. Place a cup under the main dispenser. Tap the sensor button for the drink you want. The drink you have selected will be dispensed from the main dispenser into your cup. Canceling a drink Tap the lit orange symbol on the control panel again. When preparing drinks with several ingredients (e.g.
Preparing beverages DoubleShot can be activated for all drinks apart from “Ristretto” and “Long black”. Making a DoubleShot of coffee Tap the sensor button immediately before or after you start making a drink. Dispensing starts and the sensor button lights up. 2 portions of coffee beans will be ground and brewed. Making 2 portions ( sensor button) You can dispense 2 portions of a drink into 1 large cup or into 2 cups at the same time.
Preparing beverages Tea The coffee machine is not intended for commercial or scientific purposes. Temperatures given are approximate and can vary depending on the ambient conditions. When making tea, you can select from the following options: - Japanese Tea is a high-quality green tea which boasts a fine, fresh, “green” taste. Dispensed temperature: approx. 150°F (65°C), brewing time: approx. 1.
Preparing beverages Follow the instructions for making tea on the tea packaging. The amount of tea required varies from one type of tea to another. Always follow the recommendations of the manufacturer on the packaging or of the retailer. You can adjust the amount of water according to the type of tea and the size of the cup (see “Portion size”). TeaTimer You can use the TeaTimer function to start a kitchen timer when making tea. There is a preset brewing time for the type of tea selected.
Preparing beverages Remove the tea filter or tea bag when the desired brewing time has elapsed. Dispensing warm or hot water Tea pot - Hot water at approx. 195°F (90°C) The Tea Pot function allows you to make a large quantity of tea (maximum of 1 liter). The type of tea selected determines the preset temperature. The drinks menu is displayed. You can choose between the following options: - Warm water at approx. 150°F (65°C) The drinks menu is displayed.
Expert Mode The Expert Mode function allows you to change the portion size while the drink is being made. The setting will not be saved and will only apply to the current drink. Switching Expert Mode on and off The drinks menu is displayed. Dispensing Move the indicator (small triangle) across the navigation area according to the portion size you want. Tap the sensor button. Select Settings | Expert Mode. Select the option you want. Confirm with OK. The setting is saved.
Grinder setting The grinder setting determines the contact time between the ground coffee and the water, known as the extraction time. When the ideal grinder setting is selected, the machine dispenses a perfect cup of coffee with a fine, hazelnut-brown crema. The grinder setting you select will be used for all coffee drinks. There are various ways to tell whether the coffee grinder is set correctly. The grinder setting is too coarse if the coffee or espresso is watery and tastes acidic.
Parameters Displaying and changing parameters You can change the portion size for all drinks. In addition, you can set the amount of coffee, brew temperature, and prebrewing parameters for each coffee drink individually. Tap the sensor button. Select a drink and confirm with OK. The parameters that can be changed for this drink are displayed. Once you have selected a drink, the current settings for the following appear: Amount of coffee, Brew temperature, and Pre-brewing.
Parameters Tip: For the drinks pictured on the control panel, you can change the portion size by pressing and holding the button down while the drink is being dispensed. To do this, keep the drinks button pressed until the machine starts dispensing. During dispensing, Save appears in the display. Amount of coffee The coffee machine can grind and brew 7,5–12,5 g of coffee beans per cup. The greater the amount, the stronger the coffee. The amount of coffee is too low if the espresso or coffee lacks body.
Profiles In addition to the Miele drinks menu (Miele profile), you can create individual profiles to cater for different tastes and preferences. Within the profile, you can adjust the portion sizes and parameters individually for all drinks. The name of the current profile is shown in the top left of the display. Creating a profile You can now change the drinks individually. Making drinks stored in a profile Tap the sensor button. Select the profile you want. Select the drink you want.
Profiles Change name This option can only be selected if a profile has been allocated in addition to the Miele standard profile. Select Change name and confirm with OK. Change the name as required: - To delete a character, tap the sensor button. - To enter a new character, highlight the one you want and confirm your choice with OK. - To save the modified name, select the checkmark and confirm with OK.
MobileStart With MobileStart you can, for example, start making a drink via the Miele app. You will only be able to use MobileStart if Miele@home has been set up for your coffee machine. Danger of burning and scalding at the dispensers. If liquids or steam are dispensed while the machine is unsupervised, persons may burn themselves if they place body parts under the main dispenser or touch hot components.
Settings You can use the “Settings” menu to customize the coffee system to suit your individual requirements. - Night dimming: To save energy, the time is displayed from 5:00 am to 11:00 pm only. Displaying and changing Settings Clock format The drinks menu is displayed. - 12-hour display (12 h) Tap the sensor button. Setting Select Settings and tap OK. Set the hours and the minutes. Select the menu option that you want to display or change. Confirm with OK.
Settings Once the coffee machine has come on automatically three times at the set time without any drinks being dispensed, it will stop switching on automatically. This prevents the coffee machine from switching itself on unnecessarily, for example, while you are on vacation. The programmed times will, however, remain in memory and will be reactivated after manually switching the machine on again.
Settings Eco Mode Eco Mode is an energy-saving mode. The system does not heat up until someone starts making a drink. Barista Mode This Performance Mode has been optimized for unadulterated coffee enjoyment. Users can enjoy coffeebased drinks without any delay as the coffee machine remains heated to the brewing temperature. This mode consumes more energy than Eco Mode. - Cleaning status messages or cleaning prompts are suppressed and delayed until the machine is next switched on.
Settings Water hardness °dH gpg Calcium content mg/l Ca 2+ Setting °dH or ppm (mg Ca 2+ Water hardness gpg /l) Calcium content mg/l Ca 2+ Setting or ppm (mg Ca 2+ /l) 1 1 7 1 30 31 214 30 2 2 14 2 31 32 221 31 3 3 21 3 32 33 229 32 4 4 29 4 33 34 236 33 5 5 36 5 34 35 243 34 6 6 43 6 35 36 250 35 7 7 50 7 36 37 257 36 8 8 57 8 37–45 38–47 258–321 37–45 9 9 64 9 46–60 48–62 322–429 46–60 10 10 71 10 61–70 63–73 430
Settings The system lock is reactivated when the coffee machine is next switched off. Miele@home The following points may appear under Miele@home: - Set up: This option only appears if the coffee machine has never been connected to a WiFi network or if the network configuration has been reset. - Deactivate*/Activate*: The settings for the WiFi network are retained, but the network is switched on or off. - Connection status*: Information about the WiFi connection is displayed.
Settings Running a RemoteUpdate Information about the content and scope of an update is provided in the Miele app. A message will appear in your coffee machine display if a software update is available. You can install the update immediately or postpone this until later. When the coffee machine is switched on again, you will be reminded about the update. Deactivate RemoteUpdate if you do not want to install the update. The update may take several minutes.
Cleaning and care Risk to health due to inadequate cleaning. Heat and moisture inside the coffee machine can cause coffee residues to become moldy and/or milk residues to go off and pose a risk to health. Carefully clean the coffee machine regularly.
Cleaning and care Clean by hand or in dishwasher The brew unit is not dishwasher safe. Only clean the brew unit by hand with warm water. Do not use any cleaning agents. The following components must be cleaned by hand only: Risk of damage as a result of excessively high dishwasher temperatures. Components may be ruined (e.g., may become warped) if washed in a dishwasher at temperatures higher than 130°F (55°C).
Cleaning and care Danger of burning and scalding on hot components or by hot liquids. Components can become very hot during operation. Touching hot components can cause burning. The liquids and steam dispensed are very hot and can cause scalding. Keep away from the area underneath the dispensers when hot liquids and steam are being dispensed. Always allow the coffee machine to cool down before cleaning it. Please be aware that water in the drip tray can also be very hot.
Cleaning and care Cleaning the drip tray and grounds container Danger of burning and scalding on hot components or by hot liquids. Components can become very hot during operation. Touching hot components can cause burning. The liquids and steam dispensed are very hot and can cause scalding. If the pipework has just been rinsed, wait a while before removing the drip tray. Please be aware that water in the drip tray can also be very hot. Do not touch hot components.
Cleaning and care Clean the drip tray, lid, and grounds container in the dishwasher or wash them by hand using warm water and a little liquid dish soap. Reassembling the drip tray Dry all parts. Clean the drip-tray recess inside of the coffee machine. Cleaning contacts Attach the drip-tray lid as follows: slide the lid under the lug next to the contacts and apply pressure to the lid until the catches at the sides audibly click into place.
Cleaning and care Cleaning the drip-tray cover Remove the drip-tray cover as follows: Apply pressure to the rear edge so that the cover tips forward and you can remove it easily. Clean and dry the surface that the water container sits on. The drip tray can be cleaned in the dishwasher, or by hand using warm water and a little liquid dish soap. Dry the drip-tray cover. Push the water container all the way into the coffee machine until you feel a resistance. Close the appliance door.
Cleaning and care Detach the milk pipework from the dispensing unit as follows: pull the tab to the left. Do not remove the milk pipework connecting piece. If necessary, clean the connecting piece with the cleaning brush. 56 Grip the dispensing unit by the sides and pull it down to remove it. Take the dispensing unit apart, separating it into 3 components: the Y-piece, the spouts, and the holder. Clean all parts thoroughly.
Cleaning and care Reinstall the stainless-steel cover. Close the appliance door. Fit cover to main dispenser will appear in the display. Confirm the message with OK. Cleaning the cup-rim sensor The cup-rim sensor is located under the main dispenser. Clean the area around the main dispenser with a damp cloth. Clean the cup-rim sensor at least once a week and more often if heavily soiled.
Cleaning and care Cleaning the milk flask with lid The milk flask should be taken apart and cleaned every day after use. Both the lid and the glass flask can be cleaned in the dishwasher, or by hand using warm water and a little liquid dish soap. Remove and empty the milk flask. Clean the milk-flask holder on the coffee machine with a damp cloth. Cleaning the milk valve (daily) The milk-valve seal can be damaged by objects with sharp edges or similar.
Cleaning and care Open the appliance door. Clean the milk valve with a damp cloth/microfiber cloth. On the top right-hand side of the cover, you will find a pin for swiveling the cover out. Close the appliance door. Removing and cleaning the milk valve (once a month) If the following issues occur during milk preparation, the milk valve may be blocked: only hot milk is dispensed instead of milk froth, the milk sprays out. Clean the milk valve more often if necessary.
Cleaning and care Press the retainers on the left and right-hand sides of the milk-valve holder and pull the holder forward to remove it. Pull the stainless-steel bolt upward and out. Clean the individual components of the milk valve in the dishwasher. Tip: If there are any dry milk residues on the front, soak the stainless-steel bolt in warm water and a little liquid dish soap. Installing the milk valve Insert the stainless-steel bolt from above.
Cleaning and care Connect together the angular molded hose and longer milk pipework. Start by attaching the top of the molded hose to the main dispenser. The black connecting piece should be pointing to the rear. Tip: If necessary, screw the milk pipework backward at the connecting piece on the right-hand side. Then, connect the bottom end of the molded hose to the dispensing unit. Insert the milk pipework into the milk valve on the left and right-hand sides.
Cleaning and care Cleaning the bean containers Risk of damage from incorrect use and cleaning. Immersing the bean containers in liquids can result in malfunctions. If they are taken apart, bits may break off or the mechanism may no longer work properly once they are reassembled. Do not disassemble the bean containers. Do not immerse the bean containers in liquids, e.g., soapy water. Coffee beans contain oils which can deposit on the walls of the bean containers and hinder the flow of the beans.
Cleaning and care Clean the interior and the inside of Cleaning the interior, inside of the machine door by hand with a the machine door, and drip tray Clean the interior and front of the machine as part of the normal cleaning process. For instance, if you remove the water container, use this as an opportunity to clean the area under the water container at the same time. clean and slightly damp cloth/ microfiber cloth. After cleaning, wipe the interior and machine door dry using a soft cloth.
Cleaning and care Maintenance programs Cleaning the milk pipework The coffee machine has the following maintenance programs: The milk pipework must be cleaned at least once a week. - Rinsing the machine The Clean milk pipework maintenance program lasts for approx. 15 minutes. - Rinsing the milk pipework - Cleaning the milk pipework - Degreasing the brew unit - Descaling the machine Carry out the relevant maintenance program when the prompt to do so appears in the display.
Cleaning and care Degreasing the brew unit and cleaning the interior Depending on the natural oil content of the coffee used, the brew unit can become blocked quite quickly. It must be degreased regularly in order to ensure aromatic coffee and trouble-free operation of the coffee machine. Fill the water container to the mark with lukewarm water and stir the solution. Follow the instructions for the mixing ratio carefully. Fill the water container with the specified amount of water.
Cleaning and care Remove the water container and the brew unit. Clean the interior of the machine. Rinse the brew unit by hand and refit it with a cleaning tablet in it. will appear in the display. Cleaning the brew unit and interior The moving parts of the brew unit are lubricated. Cleaning agents will damage the brew unit. Only clean the brew unit by hand with warm water. Do not use any cleaning agents.
Cleaning and care Dropping a cleaning tablet into the brew unit Wipe any remaining coffee off the two filters. One filter is located in the funnel and the other to the left of the funnel. The process of removing the brew unit causes ground coffee to drop into the drip tray. Drop a cleaning tablet into the top of the brew unit (arrow). Push the brew unit containing the cleaning tablet back into the coffee machine. Remove the drip tray and clean the lid.
Cleaning and care The cleaning process is complete when the drinks menu appears. Descaling the appliance Risk of damage from splashes from the descaling solution. Sensitive surfaces and/or natural floors can suffer damage. Wipe up any spillages immediately when descaling. Limescale builds up in the coffee machine through use. How often the machine needs to be descaled will depend on the water hardness level in your area. Limescale must be removed regularly.
Cleaning and care Add 2 descaling tablets to the water container. Fill the water container to the mark with lukewarm water. Follow the instructions for the mixing ratio carefully. Fill the water container with the specified amount of water. Otherwise, descaling will be incomplete. Carrying out descaling Reinsert the water container. Follow the additional instructions given in the display. When Fill the water container up to the symbol and insert. Close the door.
Frequently Asked Questions With the help of the following guide minor faults in the performance of the machine, some of which may result from incorrect operation, can be remedied without contacting the Service Department. This guide may help you to find the reason for the fault, and how to correct it. Messages in the display Error messages must be confirmed with OK, otherwise the message may reappear in the display even though the problem has been remedied.
Frequently Asked Questions Problem Possible cause and solution F73 or The brew unit cannot be positioned correctly or is soiled. It is not possible to press the ground coffee. Check whether you can remove the brew unit. If you can remove the brew unit, rinse it under running water. Check the brew unit Push the coffee ejector of the brew unit into the correct position (see image). Replace the water container in the coffee machine and close the door. Do not insert the brew unit.
Frequently Asked Questions Problem Possible cause and solution F233 The cup-rim sensor is not inserted or is incorrectly inserted. If the main dispenser is moving upward and the cuprim sensor is bumped, e.g., with a cup, the cup-rim sensor loses its reference position. Confirm the message with OK. Reinstall the cup-rim sensor. Cup-rim detection remains inactive and the main dispenser stays in the top position until the coffee machine is next switched on.
Frequently Asked Questions Unusual performance of the coffee system Problem Possible cause and solution The display remains dark when the coffee machine is turned on using the On/Off button . The On/Off button was not held for long enough. Tap and hold the On/Off button for at least 3 seconds. The plug is not properly plugged into the electrical socket. Insert the plug into the electrical socket. The fuse has tripped because the coffee machine, voltage, or another appliance is defective.
Frequently Asked Questions Problem Possible cause and solution A fan can be heard even though no drinks are being prepared and the coffee machine is switched off. This is not a fault. Once a drink has been dispensed or the machine has been switched off, the internal fan will continue to run until the interior is sufficiently dehumidified. The brew unit cannot be The brew unit is not positioned correctly. removed. If necessary, turn the handle on the brew unit back to the start position.
Frequently Asked Questions Problem Possible cause and solution Coffee dispensing is repeatedly interrupted and the message Fill the bean container appears in the display. This is not a fault. The brew unit has not detected the ground coffee. Certain types of coffee produce a small amount of coffee when they are ground. Usually the grinder is set too fine and the amount is set to minimum. Confirm the message with OK.
Frequently Asked Questions Problem Possible cause and solution The display lights up but the coffee machine does not heat up and no drinks are made. The Demo mode for demonstrating the coffee machine in stores and showrooms has been activated. Deactivate Demo mode (see “Settings”).
Frequently Asked Questions Unsatisfactory results Problem Possible cause and solution The coffee is not hot enough. The cup has not been pre-heated. The smaller the cup and the thicker its walls, the more important it is to pre-heat it. Pre-heat the cup with hot water, for example. The brewing temperature is set too low. Set a higher brewing temperature. The filters in the brew unit are blocked. Remove the brew unit and clean it by hand. Degrease the brew unit.
Frequently Asked Questions Problem Possible cause and solution The coffee tastes weak. The coffee grounds in the grounds container are sludgy and grainy. Less coffee is being brewed because insufficient coffee beans are getting into the grinder. Have you used a dark roast? This type of coffee bean is often oily. These oils can cling to the walls of the coffee bean containers and hinder the flow of beans.
Service and warranty Contact in the event of a fault In the event of a fault which you cannot remedy yourself, please contact your Miele dealer or Miele Customer Service. You can book a Miele Service Call online at www.miele.com/service. Appliance warranty and product registration You can register your product and/or view the manufacturer´s warranty terms and conditions for Miele appliances and vacuum cleaners at www.mieleusa.com.
Accessories These products and other useful accessories can be ordered via the Miele Webstore, from Miele Service or from your Miele dealer. - Cleaning agent for milk pipework for cleaning the milk system - Cleaning tablets for degreasing the brew unit - Descaling tablets for descaling the water pipework - CJ Jug 1.
Caring for the environment Disposal of the packing material The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of your old appliance Electrical and electronic appliances contain valuable materials.
*INSTALLATION* Installation Electrical connection Before connecting the coffee machine, make sure that the connection data on the data tag (voltage and frequency) matches the domestic electrical supply. This data must match to prevent the coffee machine from being damaged. If in any doubt, consult a qualified electrician. The necessary connection information is given on the data tag inside your appliance. The fuse rating must be at least 10 A. If possible, the socket should remain easily accessible.
*INSTALLATION* Installation Installation dimensions Installation in a tall cabinet A minimum installation height of 33 7/16" (850 mm) must be observed. Combination with other Miele Built-in Appliances is possible. If the coffee machine is to be built in above another appliance, there must be a full-width, closed shelf between them. If the machine is to be combined with a suitable built-in dishware/ food-warming drawer, no shelf is required in between.
*INSTALLATION* Installation Installation and connections A Cut-out (at least 20"/508 mm wide) in the niche floor of the tall cabinet for power cord and ventilation E Electrical connection No electrical or plumbed-water connection in this area 84
*INSTALLATION* Installation Building in the coffee machine Danger of injury due to incorrect operation. A machine that has not been built in is not safe and can cause injuries. Do not operate the coffee machine unless it has been built in. Danger of damage due to incorrect operation. If the ambient temperature range is not observed, the coffee machine may not function properly. The coffee machine may only be operated within an ambient temperature range of +60°F to +100°F (+16°C to +38°C).
*INSTALLATION* Installation Connecting the electricity supply Observe the information under “Electrical connection”. Connect the coffee machine to the electricity supply. Pushing in and aligning the coffee machine Take care not to trap or damage the electrical connection when pushing the machine into the niche. Push the coffee machine all the way into the niche until you feel a resistance.
*INSTALLATION* Installation The door opening limiters can be removed, allowing you to increase the opening angle to approx. 170°. This makes it easier to remove the bean containers, for example. Removing the door opening limiters Make sure that sufficient space is available for the larger door opening angle and that the machine door is not going to hit an adjacent wall. Remove the door opening limiters from the hinges, e.g., by prizing them out with a screwdriver.
FCC Declaration of Conformity Electricity consumption in standby: < 0,6 W Electricity consumption in networked standby: < 0,9 W Frequency range 2.412 GHz – 2.462 GHz Maximum transmitting power < 100 mW WiFi module EK037 Contains FCC ID: 2ACUWEK037 Contains IC: 5669C-EK037 This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s).
Please have the model and serial number of your appliance available when contacting Customer Service. U.S.A. Canada Miele, Inc. Importer Miele Limited National Headquarters 9 Independence Way Princeton, NJ 08540 www.mieleusa.com Customer Support Phone: 888-99-MIELE (64353) info@mieleusa.com International Headquarters Miele & Cie. KG Carl-Miele-Straße 29 33332 Gütersloh Germany Headquarters and Miele Centre 161 Four Valley Drive Vaughan, ON L4K 4V8 www.miele.
CVA 7440 en-US M.-Nr.