Operating and installation instructions Built-in coffee machine To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr.
Caring for the environment Disposal of the packing material Disposing of your old appliance The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Electrical and electronic appliances often contain valuable materials. They also contain specific materials, compounds and components, which were essential for their correct function and safety.
Contents Caring for the environment .............................................................................. 2 Warning and Safety instructions...................................................................... 7 Guide to the machine ....................................................................................... 16 Operation............................................................................................................ Touch display ...........................................
Contents Parameters......................................................................................................... Displaying and changing parameters .................................................................. Ground quantity................................................................................................... Brewing temperature ........................................................................................... Pre-brewing the ground coffee.............................
Contents Water hardness ................................................................................................... Movement sensor................................................................................................ System lock .................................................................................................... Miele@home ........................................................................................................ Remote control...............................
Contents Cancelling automatic cleaning and descaling..................................................... 87 Problem solving guide ...................................................................................... Messages in the display...................................................................................... Unusual performance of the coffee machine ...................................................... Faults with automatic cleaning and/or descaling .......................................
Warning and Safety instructions This coffee machine complies with all the stipulated safety requirements. Inappropriate use can, however, lead to personal injury and material damage. Read the operating instructions carefully before using the coffee machine. They contain important information on safety, installation, use and maintenance. This prevents both personal injury and damage to the coffee machine.
Warning and Safety instructions Correct application This coffee machine is intended for home use. This coffee machine is not intended for outdoor use. This coffee machine must not be used at altitudes above 2000 m. It must only be used as a domestic appliance to make espresso, cappuccino, latte macchiato, tea etc. Any other use is not permitted.
Warning and Safety instructions Safety with children Danger of burning and scalding on the dispensing spouts. Children's skin is far more sensitive to high temperatures than that of adults. Ensure children do not touch hot surfaces of the coffee machine or place parts of their body under the dispensing spouts. Install the coffee machine where it is out of the reach of children. Children under 8 years of age must be kept away from the coffee machine unless they are constantly supervised.
Warning and Safety instructions Technical safety Installation work or repairs should only be carried out by a Miele authorised technician. Unauthorised or incorrect installation work or repairs can pose considerable danger to users. A damaged coffee machine could be dangerous. Before building in the machine, check it for any externally visible damage. Do not use a damaged machine.
Warning and Safety instructions A minimum installation height of 850 mm must be observed. This coffee machine must not be installed behind a closed cabinet door because heat and moisture can build up behind it. This can result in damage to the machine and/or furniture unit. The coffee machine must be disconnected from the electricity supply during repair work. While the machine is under warranty, repairs should only be undertaken by a Miele authorised service technician.
Warning and Safety instructions Correct use Danger of burning and scalding on the dispensing spouts. The liquids and steam dispensed are very hot. Keep well away from the area underneath the spouts when hot liquids and steam are being dispensed. Do not touch hot components. Hot liquid or steam could spatter from the nozzles. Ensure that the central spout is clean and fitted correctly. Before opening the door, remove any containers from the drip tray in the machine door.
Warning and Safety instructions Do not use green (unroasted) coffee beans or mixtures of coffee beans which contain green coffee beans. Green coffee beans are very hard and still contain residual moisture. These can damage the coffee machine grinder as soon as grinding begins. Do not use coffee beans which have been treated with caramel, sugar or other substances including sugary liquids. Sugar will damage the coffee machine.
Warning and Safety instructions Cleaning and care Clean the coffee machine and the milk flask daily, particularly before using them for the first time. All parts of the milk system need to be cleaned thoroughly and regularly. Milk contains bacteria which proliferate rapidly with inadequate cleaning.
Warning and Safety instructions For machines with stainless steel surfaces: Do not use sticky notes, transparent adhesive tape, masking tape or other types of adhesive on the stainless steel surfaces. These will damage the stainless steel surfaces, causing them to lose their dirtrepellent protective coating. The finish on stainless steel surfaces is susceptible to scratching. Even magnets can cause scratching.
Guide to the machine Exterior view 1 2 3 4 5 6 7 8 11 9 10 a On/Off button b Optical interface (for the Miele Customer Service Department only) c MobileStart sensor d Movement sensor e “Back” sensor f Touch display g “Light” sensor h Door handle i Height-adjustable central spout with lighting j Drip tray cover k Milk flask 16
Guide to the machine Interior view a Bean containers (Type A and Type C) b Milk valve c Height-adjustable central spout with lighting d Grinder setting e Bean container (Type B) f Fan outlet g Water container h Drip tray with lid i Brew unit j Waste container k Maintenance container l Receptacles for cleaning and descaling cartridges (including adapters) m Drip tray 17
Operation Touch display The delicate touch display can be scratched by pointed or sharp objects, e.g. pens. Only touch the display with your fingers. The touch display is split into multiple areas. Miele 12:00 Ristretto Espresso Coffee Long coffee Profiles The menu path appears on the left of the header. If you touch a menu name in the header, the display will switch to that menu. To switch to the start screen, touch . The time of day is shown on the right of the header.
Operation Operating actions All the selectable options are displayed in black or white according to your selected colour scheme. Each time you touch a possible option, the relevant characters (word and/or symbol) light up orange. Selecting a menu option Touch the field or value you want in the display. Scrolling You can scroll left or right. Swipe the screen by placing your finger on the touch display and moving it in the direction you want.
Operation OK Select the value you want: as soon as you enter a valid value, OK turns green. Use the arrow to delete the last entered number. Confirm with OK. Entering a name Letters are entered using a keyboard. It is best to select short names. Touch the letters or characters you want. Tip: Use the arrow to delete the last entered character. Touch Save. Displaying the context menu When you are in certain menus, a context menu can be displayed, e.g. for configuring drinks.
Operation Help Context-sensitive help is available for certain functions. In this case, Help appears in the bottom line. Touch Help to display information in text and pictures. Touch Close to return to the previous menu. Pull-down menu Among other things, the pull-down menu provides access to a schematic representation of the bean containers and to Expert mode. Touch the orange line at the top edge of the screen and drag down with your finger. Active settings are highlighted in orange.
Operation Symbols in the display The display shows symbols as well as text, e.g. symbols for the various drinks. Some of these are explained below. Symbol Explanation This symbol indicates that there is additional information and advice about using the coffee machine. Select OK to confirm the information. This symbol indicates the “Settings” menu and the “Language” menu option. This symbol appears if the system lock is activated. Operation is locked.
Miele@home Your coffee machine is equipped with an integrated WiFi module. In order to use it, you will need: - A WiFi network - The Miele@mobile app - A Miele user account The user account can be created via the Miele@mobile app. Availability of the WiFi connection The WiFi connection shares a frequency range with other appliances (including microwave ovens and remote control toys). This can give rise to sporadic or even complete connection failures.
Before using for the first time Before using for the first time Connect the coffee machine to the electricity supply. Install the coffee machine by building it in. Remove any notices from the machine. Remove the protective foil from the drip tray cover. Clean the machine thoroughly (see “Cleaning and care”) before filling it with water and coffee beans. Clean the coffee machine (see “Cleaning and care”).
Before using for the first time Setting the water hardness level Contact your local water supplier to find out your local water hardness range if necessary. More information can be found under “Settings – Water hardness”. Enter your local water hardness (in °dH) and confirm with OK. Setting up automatic cleaning and descaling Information about automatic cleaning and descaling will appear in the display. Remove the maintenance container on the left-hand side. Confirm with OK.
Before using for the first time Put the maintenance container back inside the coffee machine and close the appliance door. The descaling cartridge will fill with water the next time the machine is switched off. Always wait for the coffee machine to switch itself off. Do not force the machine to switch off. Screw the cleaning cartridge into the holder upside down. Push the holder and cartridge into the coffee machine until the holder audibly clicks into place.
Before using for the first time The coffee machine is now successfully set up for use. You can now fill the bean system. Push the bean containers all the way back into the coffee machine. Close the machine door. Setting up the bean system Tip: Make a note of each type of bean. After setting up the coffee machine, you will be prompted to set up the bean system. The coffee machine will assist you when first filling and naming the bean containers.
Before using for the first time Allocating types of beans Now you need to allocate the drinks to the types of beans. Selected drinks are highlighted in orange. Now select the drinks that are to be prepared with this type of bean. Confirm your selection with OK. Now it is time to allocate the next type of bean. The coffee drinks that have not yet been allocated are displayed. Select the drinks that are to be prepared with this type of bean. Confirm with OK.
Bean system Coffee or espresso can be made from whole roasted coffee beans which are freshly ground for each portion. Your coffee machine has a bean system with 3 bean containers which can be filled with different types of beans or even just one type. You can allocate bean types to individual coffee drinks however you like. Alternatively, you can create your own user profiles that do not have the same bean types allocated to the coffee drinks as the Miele profiles.
Bean system If you switch from having identical names to having different names, you will then need to allocate coffee drinks to the newly named type of bean. Changing how the bean containers are allocated If you have created extra user profiles for coffee drinks in addition to the Miele standard profile, the bean types can be individually allocated to the drinks in each profile. Touch Change allocation. If you have set up 1 or more profiles and at least 1 coffee drink, first select the profile.
Filling the water container Risk to health due to contaminated water. Bacteria can develop in water which has been sitting in the water container for too long and is a risk to your health. Change the water in the water container every day. Risk of damage due to incorrect operation. Unsuitable liquids such as hot or warm water or other liquids can damage the coffee machine. Bottled mineral water leaves too much limescale in the coffee machine. Only use cold, fresh tap water to fill the water container.
Switching on and off Switching the coffee machine on Switching off for longer periods of time Touch the On/Off button . If the coffee machine is not going to be used for a while, e.g. if you are going on holiday, remember to do the following: The coffee machine heats up and rinses the pipework. Hot water will run out of the central spout. You can now make drinks. If the coffee machine is already at operating temperature, rinsing will not take place.
Spout adjustment The central spout cannot be manually adjusted. Before making the drink, the central spout moves down and the cup sensor stops it at the optimum height for the cups or glasses being used. When the coffee machine is switched off, the central spout will be in the middle position. When a maintenance programme is being carried out, the central spout will move to the height of the maintenance container or into a low maintenance position.
Making drinks Danger of burning and scalding on the dispensing spouts. The liquids and steam dispensed are very hot and can cause scalding. Keep well away from the area underneath the spouts when hot liquids and steam are being dispensed. Do not touch hot components. Making coffee with and without milk The following drinks can be made: - Ristretto is a strong, concentrated espresso. It is prepared with the same amount of coffee as for an espresso but with a lot less water.
Making drinks Milk preparation Milk or milk alternatives (e.g. soya milk) containing added sugar can clog up the milk pipe and the rest of the milk pipework. Residues from unsuitable liquids can interfere with milk preparation. The milk used must not contain any additives. Only use pasteurised cow's milk. Tip: Using cold cow's milk (< 10 °C) with a protein content of at least 3 % will produce the perfect milk froth. You can select milk with a fat content according to preference. With whole milk (at least 3.
Making drinks Making a coffee Push the milk flask back into the coffee machine until it clicks into place. Tip: It is easier to remove the milk flask with both hands. Place a container underneath the central spout. Select a coffee drink. Preparation will begin and the coffee will be dispensed into the container from the central spout. Cancelling a drink Press Stop or Cancel.
Making drinks DoubleShot Select the DoubleShot function if you would like a particularly strong and aromatic coffee. In this case, more coffee beans will be ground and brewed halfway through the brewing process. The shorter extraction time means that fewer unwanted aromas and bitter compounds will be released. DoubleShot can be activated for all drinks apart from “Ristretto” and “Long black”. Making a DoubleShot of coffee The symbol will appear while drinks are being made.
Making drinks Coffee pot You can make several cups of coffee one after the other automatically with the Coffee pot function (maximum of 1 litre). The drinks menu is displayed. Tip: Make sure that the bean and water containers have enough beans and water inside them before starting the Coffee pot function. Place a sufficiently large container under the central spout. Select Coffee pot. Tip: You will find Coffee pot at the end of the drinks menu. Select the number of cups you want (3 to 8).
Making drinks - Chai latte has its origins in traditional Ayurveda medicine as a black tea with typically Indian spices and milk. The milk mellows the spices and tops off the flavour experience. Dispensed temperature: approx. 97 °C, brewing time: approx. 3 minutes - Herbal tea is an aromatic infusion drink made up of dried leaves or fresh parts of plants. Dispensed temperature: approx. 97 °C, brewing time: approx. 8 minutes - Fruit tea is made from dried pieces of fruit and/or parts of plants, e.g.
Making drinks The drinks menu is displayed. Teapot Touch the sensor. Select the setting you want. The Teapot function allows you to make a large quantity of tea (maximum of 1 litre). The type of tea selected determines the preset temperature. Making tea The drinks menu is displayed. The drinks menu is displayed. Tip: Make sure that the water container has enough water inside it before you start making a pot of tea. Select Settings | Timer | TeaTimer.
Expert mode In Expert mode, you can allocate a bean type temporarily and change the portion size while the drink is being made. The setting will not be saved and will only apply for the current drink. Activating and deactivating Expert mode Expert mode is located in the pull-down menu at the top edge of the screen. Touch the top edge of the screen in the middle and drag down with your finger to open Expert mode. The schematic representation of the bean containers is displayed. Touch Expert mode.
Grinder setting When the beans are ground correctly, the coffee or espresso will flow evenly into the cup with a good crema. The crema should have an even hazelnut brown colour. Remove the water container. The grinder setting you select will be used for all coffee drinks. There are various ways to tell whether the coffee grinder is set correctly.
Parameters Displaying and changing parameters Increase the amount of coffee so that more ground coffee is brewed. You can individually adjust the following parameters for each drink: The amount of coffee is too high, if - Type of beans - espresso or coffee flows into the cup very slowly, - Amount of coffee - the crema is dark brown, - Brew temperature - the espresso or coffee tastes bitter. - Pre-brewing Decrease the amount of coffee so that less ground coffee is brewed.
Parameters Type of beans You can display which type of bean is currently being used for this coffee drink or change which bean container is allocated to it.
Portion size The flavour of the coffee produced depends not only on the type of coffee, but also on the amount of water used. You can programme the amount of water for all coffee drinks, tea and hot water to suit the size of your cups and the type of coffee you are using. This does not alter the amount of coffee used. For coffee drinks with milk, you can also set the amount of milk or milk froth to suit your personal taste. You can also set the portion sizes for hot milk and milk froth.
Resetting drinks You can reset portion sizes and parameters to their factory default settings for individual drinks or for all drinks. The drinks menu is displayed. Touch the drink you want and keep your finger on it until the context menu opens. Select Reset and confirm with Yes. The portion size and parameters are reset to their factory default settings. The allocated bean type remains stored.
Profiles In addition to the Miele drinks menu (Miele profile), you can create individual profiles to cater for different tastes and preferences. Within the profile, you can adjust the portion sizes and parameters individually for all drinks. - Manual: The selected profile will remain active until you select another one. - After each use: The machine will revert to the Miele profile whenever a drink is dispensed. Select the option you want.
Profiles: creating and editing drinks You can save frequently made drinks in a profile with your own individual settings (see “Profiles”). Touch the name of the drink and keep your finger on it until the context menu appears. You can also change the names of your drinks and delete any unwanted drinks from your profile. You can save a maximum of 9 drinks in a profile. Edit the entry as required. Creating a drink You can create new drinks based on existing drinks. The drinks menu is displayed.
MyMiele You can display drinks you make frequently, drinks from profiles and maintenance programmes in the MyMiele screen. Tip: You can also set menu options that you have entered in MyMiele as your start screen (see “Settings – Start screen”). The main menu is displayed. Touch MyMiele. You can now configure MyMiele. MyMiele: adding an entry Touch Add entry. You can now add entries from the following menus: - Drinks - Profiles - Maintenance Select an entry. Confirm the message with OK.
MobileStart With MobileStart you can, for example, start making a drink via the Miele@mobile app. You will only be able to use MobileStart if Miele@home has been set up for your coffee machine. Danger of burning and scalding on the dispensing spouts. If liquids or steam are dispensed while the machine is unsupervised, persons may burn themselves if they place body parts under the central spout or touch hot components.
Settings You can personalise your coffee machine by adapting the factory default settings to suit your requirements. - Night dimming: To save energy, the time is only displayed between 5 am and 11 pm. Displaying and changing settings Clock type Touch the sensor. The time of day can be displayed in analogue (clock face) or digital (hours: minutes plus date) format when the coffee machine is switched off. Select Settings. Clock format Select the option you want to change.
Settings “MyMiele”). The new start screen will appear when the coffee machine is next switched on. The drinks menu is set as the start screen by default. Timer Appliance timer You can set different times for the timer at the weekend (Sat. and Sun.) and/or from Monday to Friday (Monday-Friday). Alternatively, you can select Daily to use the same timer settings every day. Tip: If you are unable to set the timers because the screen is greyed out, touch On to enable timer adjustment.
Settings TeaTimer You can use the TeaTimer to start a minute minder when making tea (see “Making drinks – TeaTimer”). Volume You can set the volume of the buzzer and keypad tones using the bar chart. Display Brightness The display brightness is adjusted via a bar with seven segments. Colour scheme Choose between a light or dark colour scheme for the display.
Settings Barista mode This performance mode has been optimised for unadulterated coffee enjoyment. Users can enjoy coffeebased drinks without any delay as the coffee machine remains heated to the brewing temperature. This mode consumes more energy than Eco mode. Latte mode This performance mode has been optimised for preparing milk. Milkbased drinks can be prepared within a much shorter space of time. This mode consumes more energy than Eco mode and Barista mode.
Settings Water hardness °dH mmol/l Calcium content mg/l Ca 2+ Setting s or ppm (mg Ca 2+ Water hardness °dH mmol/l /l) Calcium content mg/l Ca 2+ Setting s or ppm (mg Ca 2+ /l) 1 0.2 7 1 30 5.4 214 30 2 0.4 14 2 31 5.5 221 31 3 0.5 21 3 32 5.7 229 32 4 0.7 29 4 33 5.9 236 33 5 0.9 36 5 34 6.1 243 34 6 1.1 43 6 35 6.3 250 35 7 1.3 50 7 36 6.4 257 36 8 1.4 57 8 37–45 6.6–8.0 258–321 37–45 9 1.6 64 9 46–60 8.2–10.
Settings - Acknowledge buzzer: Buzzer sounds are suppressed, e.g. in the event of the message Fill and replace the water container. - Set up: This option only appears if the coffee machine has never been connected to a WiFi network or if the network configuration has been reset. - Switch the appliance on: The start screen is displayed. - Deactivate*/Activate*: The settings for the WiFi network are retained, but the network is switched on or off. The movement sensor is deactivated by default.
Settings Miele@mobile app. To start making a drink via the app, MobileStart must be activated as well. The remote control function is switched on by default. SuperVision The SuperVision option appears when the coffee machine is connected to a WiFi network. SuperVision allows you to monitor other household appliances in the Miele@home system. SuperVision display When SuperVision is on (SuperVision | On), the symbol appears in the display.
Settings Deactivate RemoteUpdate if you do not want to install the update. The update may take several minutes. Please note the following information about the RemoteUpdate function: - You will only receive a message when an update is available. - Once an update has been installed, it cannot be undone. - Do not switch the coffee machine off during the update. Otherwise, the update will be aborted and will not be installed.
Cleaning and care Risk to health due to inadequate cleaning Heat and moisture inside the coffee machine can cause coffee residues to become mouldy and/or milk residues to go off and pose a risk to health. Carefully clean the coffee machine regularly.
Cleaning and care Cleaning by hand or in the dishwasher The brew unit is not dishwasher safe. Clean the brew unit by hand only under warm running water. Do not use washing-up liquid or any other cleaning agent. The following components must be cleaned by hand only: - Central spout stainless steel cover - Brew unit - Bean containers and lids Risk of damage as a result of excessively high dishwasher temperatures. Components may be ruined (e.g.
Cleaning and care Danger of burning and scalding on hot components or by hot liquids. Components can become very hot during operation. Touching hot components can cause burning. The liquids and steam dispensed are very hot and can cause scalding. Keep well away from the area underneath the spouts when hot liquids and steam are being dispensed. Always allow the coffee machine to cool down before cleaning it. Please be aware that water in the drip tray can also be very hot.
Cleaning and care - Steel wool or stainless steel wire scourers Cleaning the drip tray and waste container Danger of burning and scalding on hot components or by hot liquids. Components can become very hot during operation. Touching hot components can cause burning. The liquids and steam dispensed are very hot and can cause scalding. If the pipework has just been rinsed, wait a while before removing the drip tray. Please be aware that water in the drip tray can also be very hot.
Cleaning and care Clean the drip tray, lid and waste container in the dishwasher or wash them by hand using warm water and a little washing-up liquid. Dry all parts thoroughly. Clean the inside of the coffee machine underneath where the drip tray goes. Cleaning contacts Remove the drip tray and waste container from the machine. Empty the waste container after removing it from the drip tray. The waste container may contain a small amount of water from rinsing as well as the leftover coffee grounds.
Cleaning and care Reassembling the drip tray Cleaning the drip tray cover Attach the drip tray lid as follows: slide the lid under the lug next to the contacts and apply pressure to the lid until the catches at the sides audibly click into place. Remove the drip tray cover as follows: apply pressure to the rear edge so that the cover tips forwards and you can remove it easily. The drip tray cover can be cleaned in the dishwasher, or by hand using warm water and a little washing-up liquid.
Cleaning and care Clean and dry the surface that the water container sits on. Fill the water container with fresh, cold tap water. Pull the central spout's stainless steel cover forwards to remove it. Then clean it. Push the water container all the way into the coffee machine until you feel a resistance. Close the machine door. Please note that the automatic maintenance programmes will only work if the water container has been adequately filled and correctly fitted in the machine.
Cleaning and care Do not remove the milk pipe connecting piece. If necessary, clean the connecting piece with the cleaning brush. Grip the dispensing unit by the sides and pull it down to remove it. Take the dispensing unit apart, separating it into 3 components: the Y-piece, the spouts and the holder. Clean all parts thoroughly. Clean the area around the central spout with a damp cloth.
Cleaning and care Fit the dispensing unit back together. Press down firmly so that the spouts become securely connected to the holder. Press the two retainers together (see arrows). The cup rim sensor is released. Insert the dispensing unit into the coffee machine and connect the milk pipe. Refit the stainless steel cover. Close the machine door.
Cleaning and care Cleaning the milk valve (daily) The milk valve seal can be damaged by objects with sharp edges or similar. Do not use any sharp-edged objects (such as knives) to clean the milk valve. Rinse the milk pipework in the lid under running water and then place the lid in the dishwasher. If no water runs out of the connecting piece , clean it with the cleaning brush. Clean the glass flask. Dry all parts and especially the threads on the lid and on the glass with a clean cloth.
Cleaning and care Removing and cleaning the milk valve (once a month) If the following issues occur during milk preparation, the milk valve may be blocked: only hot milk is dispensed instead of milk froth, the milk sprays out. Clean the milk valve more often if necessary. 3 2 1 The milk valve cover should only be cleaned by hand. Open the appliance door. Remove the bean container on the left and the maintenance container. Remove the central spout’s stainless steel cover.
Cleaning and care Press the latches on the left and right-hand sides of the milk valve holder and pull the holder forwards to remove it. Pull the stainless steel bolt upwards and out. Clean the individual components of the milk valve in the dishwasher. Tip: If there are any dry milk residues on the front, soak the stainless steel bolt in warm water and a little washingup liquid. Fitting the milk valve Insert the stainless steel bolt from above.
Cleaning and care Connect together the angular moulded hose and longer milk pipework. Start by attaching the moulded hose to the top of the central spout. The black connecting piece should be pointing to the rear. Tip: If necessary, turn the milk pipework towards the back at the connecting piece on the right-hand side. Then, connect the bottom end of the moulded hose to the dispensing unit. Insert the milk pipework into the milk valve on the left and right-hand sides.
Cleaning and care Cleaning the bean containers Risk of damage from incorrect use and cleaning. Immersing the bean containers in liquids can result in malfunctions. If they are taken apart, bits may break off or the mechanism may no longer work properly once they are reassembled. Do not disassemble the bean containers. Do not immerse the bean containers in liquids, e.g. soapy water. Coffee beans contain oils which can deposit themselves on the walls of the bean containers and hinder the flow of the beans.
Cleaning and care Brew unit removal and cleaning by hand The moving parts of the brew unit are lubricated. Cleaning agents and washing-up liquid will damage the brew unit. Clean the brew unit by hand only under warm running water. Do not use washing-up liquid or any other cleaning agent. Remove and clean the brew unit once a week. Also clean the area below the brew unit once a week. First, pull the brew unit sideways and then tip it forwards and slide it out that way . Open the machine door.
Cleaning and care Tip: If you are unable to turn the brew unit handle, apply firm pressure to the sides of the brew unit. Push the water container into the coffee machine. The process of removing and inserting the brew unit causes ground coffee to drop into the drip tray. Wipe any remaining coffee residue from the filters. One filter is located in the funnel. The other filter can be found to the left of the funnel. Dry the funnel to prevent ground coffee sticking to it the next time a coffee is made.
Cleaning and care Open the machine door. Remove and clean the drip tray. Remove the following parts from the interior: - Water container - Drip tray - Maintenance container Tip: Before cleaning the control panel, open the machine door to prevent accidental operation. Clean the front of the machine with a clean and slightly damp cloth/ microfibre cloth. After cleaning, wipe the surfaces dry using a soft cloth. Tip: You can also use a Miele microfibre cloth to clean the front.
Cleaning and care Maintenance programmes Rinsing the milk pipework The coffee machine has maintenance programmes for: If you have made a drink with milk, the coffee machine will rinse the milk pipework automatically after a few minutes. You can also start the Rinse the milk pipework function manually.
Cleaning and care For optimal cleaning results, we recommend Miele cleaning agent for milk pipework. The cleaning agent for milk pipework has been specially developed for use with Miele coffee machines and prevents subsequent damage. For each cleaning process, you will need 2 sticks of the cleaning agent for milk pipework. It is available to order via the Miele webshop or directly from Miele (see the end of this booklet for contact details). Clean the milk pipework appears in the display.
Cleaning and care be degreased regularly in order to ensure aromatic coffee and trouble-free operation of the coffee machine. You can run the maintenance programme with the Miele cleaning cartridge or with cleaning tablets for degreasing the brew unit. The maintenance programme lasts for approx. 10 minutes. If you have switched on automatic cleaning and fitted a ready-to-use cleaning cartridge, the Degrease the brew unit maintenance programme will run using the cleaning cartridge.
Cleaning and care First, pull the brew unit sideways and then tip it forwards and slide it out that way . If you cannot remove the brew unit or can only do so with difficulty, the brew unit is not in the correct position (see “Problem solving guide”). When you have removed the brew unit, do not change the position of the handle on the brew unit. Otherwise, the brew unit cannot be inserted. Clean the brew unit by hand under warm running water without using cleaning agent or washing-up liquid.
Cleaning and care Push the brew unit containing the cleaning tablet back into the coffee machine. depend on the water hardness level in your area. Limescale must be removed regularly. The appliance will guide you through the descaling process. Various messages will appear in the display, e.g. you will be prompted to empty the drip tray or fill the water container. Descaling must be carried out. The process takes approx. 35 minutes.
Cleaning and care Descaling after prompt appears in the display Descale the appliance appears in the display. Descaling cannot be cancelled once it has started. It must be completed through to the end. Confirm the message with OK. The process will start. Follow the instructions in the display. When Place 2 descaling tablets in the water container and fill it with lukewarm water up to the descaling symbol and insert it appears in the display, proceed as follows.
Automatic cleaning and descaling Risk of damage from spilt cleaning and descaling solution. Sensitive surfaces and/or natural floors can suffer damage. One way to catch the cleaning and descaling solution is to place the maintenance container under the central spout before switching off the machine. Clear up any spillages of cleaning and descaling solution.
Automatic cleaning and descaling - Carry out the instructions which appear in the display before switchoff, e.g. Empty and refit the drip tray and the waste container. - The appliance door is closed when the programme is started. - The coffee machine is switched off. Automatic cleaning If you have made a drink containing milk within the last 24 hours, the milk pipework will be cleaned. The brew unit will be cleaned after making approx. 25 coffee drinks. Automatic cleaning takes approx. 25 minutes.
Automatic cleaning and descaling If no cleaning cartridge has been fitted or if the fitted cartridge is empty or has expired, the milk pipework and brew unit must be cleaned manually. For this, you will need the appropriate cleaning agents (see “Cleaning and care” – “Cleaning the milk pipework” and “Degreasing the brew unit”). You can leave the cleaning cartridge in place during long periods of non-use or when transporting the coffee machine.
Automatic cleaning and descaling Automatic descaling Automatic descaling takes approx. 12 minutes. To ensure the longevity of components and a consistent environment free of limescale, the coffee machine needs to be manually descaled from time to time. The intervals are determined by your usage behaviour and the water hardness level of your area. If you make a lot of coffees with milk, for example, you will need to descale the coffee machine more frequently with the descaling tablets.
Automatic cleaning and descaling - It should be transported with care and upright. Avoid shaking it. Shaking or turning upside down reduces the shelf life or damages the cartridge. - The cartridge should be stored upright, in a dark place and at room temperature (16 - 38 °C). Replacing the descaling cartridge Removing the descaling cartridge Open the machine door and remove the maintenance container. Tip: You can seal the descaling cartridge with the cap that can be found on the cartridge.
Automatic cleaning and descaling If you do not want to fit a descaling cartridge, seal the system with the adapter. The start time is saved. From now on, the automatic maintenance programmes will commence at the desired time each day. Cancelling automatic cleaning and descaling You can cancel the automatic cleaning programmes during the activation phase. Insert the adapter in place of the cartridge.
Problem solving guide Many malfunctions and faults that can occur in daily operation can be easily remedied. Time and money will be saved because a service call will not be needed. The following guide may help you to find the reason for a malfunction or a fault, and to correct it. Messages in the display Error messages must be confirmed with OK, otherwise the message can reappear in the display even though the problem has been remedied.
Problem solving guide Problem Cause and remedy F73 or The brew unit cannot be positioned correctly or is soiled. It is not possible to press the ground coffee. Check whether you can remove the brew unit. If you can remove the brew unit, rinse it under running water. Check the brew unit Push the coffee ejector of the brew unit into the correct position (see illustration). Place the water container in the coffee machine and close the machine door. Do not insert the brew unit.
Problem solving guide Problem Cause and remedy F233 The cup rim sensor is not inserted or is incorrectly inserted. If the central spout is moving upwards and the cup rim sensor is bumped, e.g. with a cup, the cup rim sensor loses its reference position. Confirm the message with OK. Refit the cup rim sensor. Cup rim detection remains inactive and the central spout stays in the top position until the coffee machine is next switched on.
Problem solving guide Unusual performance of the coffee machine Problem Cause and remedy The display remains dark when the coffee machine is turned on using the On/Off button . The On/Off button was not held for long enough. Touch and hold the On/Off button for at least 3 seconds. The plug is not inserted in the socket correctly. Insert the plug into the socket. The fuse has tripped because the coffee machine, voltage or another appliance is defective.
Problem solving guide Problem Cause and remedy A fan can be heard even though no drinks are being prepared or the coffee machine is switched off. This is not a fault. Once a drink has been dispensed or the machine has been switched off, the internal fan will continue to run until the interior is sufficiently dehumidified. The brew unit cannot be The brew unit is not positioned correctly. removed. If necessary, move the handle on the brew unit back to the start position. Close the machine door.
Problem solving guide Problem Cause and remedy Steam is dispensed instead of water while preparing hot water or making tea. It is likely that the wrong altitude has been set. Change the altitude settings (Settings Altitude). If necessary, you can also change the temperature settings for the drinks (Drink parameters). The display is hard to see or not able to be read. The display brightness has been set too low. Change this setting (see “Settings”).
Problem solving guide Faults with automatic cleaning and/or descaling Problem Cause and remedy After switching on, a message appears informing you that automatic cleaning and/or descaling could not be carried out. All removable parts, such as the water container, drip tray, brew unit or central spout, must be fitted. The water container must be filled with water at least up to the descaling symbol . The machine door was not closed. Confirm the message with OK.
Problem solving guide Problem Cause and remedy When the machine is switched on, one of these messages appears: Automatic cleaning Automatic cleaning could not be carried out twice. could not be carried out. Start Automatic cleaning (duration min.) now? Otherwise Automatic cleaning will be permanently switched off or: Automatic maintenance could not be carried out.
Problem solving guide Unsatisfactory results Problem Cause and remedy The coffee is not hot enough. The cup has not been pre-heated. The smaller the cup and the thicker its sides, the more important it is to pre-heat it. Pre-heat the cup, for example, with hot water. The brewing temperature has been set too low. Set a higher brewing temperature. The filters in the brew unit are blocked. Remove the brew unit and clean by hand Degrease the brew unit.
Problem solving guide Problem Cause and remedy The coffee tastes weak. The coffee grounds in the waste container are sludgy and grainy. Less coffee is being brewed because insufficient coffee beans are getting into the grinder. Have you used a dark roast? This type of coffee bean is often more oily. These oils can cling to the inside of the bean containers and hinder the flow of beans.
Problem solving guide Problem Cause and remedy Coffee drinks trickle/ The brew unit is blocked because the coffee machine dribble slowly out of the has been used very intensively. And/or the brew unit central spout. has not been regularly removed and cleaned by hand. If a cleaning cartridge is fitted, start by switching off Automatic cleaning (Settings | Automatic cleaning).
After sales service and warranty After sales service Warranty In the event of a fault which you cannot correct yourself, or if the machine is under guarantee please contact: For information on the appliance warranty specific to your country please contact Miele. See back cover for address. - your Miele Dealer or - Miele. Contact details for Miele are given at the end of this booklet. N.B.
Accessories These products and other useful accessories can be ordered via the Miele webshop, from Miele (see back cover for contact details) or from your Miele dealer.
*INSTALLATION* Installation Electrical connection Before connecting the coffee machine, make sure that the connection data on the data plate (voltage and frequency) matches that of the electricity supply. This data must correspond in order to avoid the risk of damage to the coffee machine. If in any doubt, consult a qualified electrician. The necessary connection data is given on the data plate inside your appliance. The fuse rating must be at least 10 A.
*INSTALLATION* Installation Building-in dimensions Installation in a tall unit A minimum installation height of 850 mm must be observed. All dimensions are given in mm. The machine can be combined with other Miele built-in appliances. In this case, there must be a full-width, closed shelf between them. If the machine it to be combined with a suitable built-in plate/food-warming drawer, no shelf is required in between.
*INSTALLATION* Installation Installation and connections All dimensions are given in mm.
*INSTALLATION* Installation Building in the coffee machine Danger of injury due to incorrect operation. A machine that has not been built in is not safe and can cause injuries. Do not operate the coffee machine unless it has been built in. Danger of damage due to incorrect operation. If the ambient temperature range is not observed, the coffee machine may not function properly. The coffee machine may only be operated within an ambient temperature range of +16 °C to +38 °C.
*INSTALLATION* Installation Open the appliance door. The door opening limiters can be removed, allowing you to increase the opening angle to approx. 170°. This makes it easier to remove the bean containers, for example. Two TX20 (25 mm) screws are included with the coffee machine. Secure the coffee machine to the side walls of the furniture unit using the screws supplied. Tighten both screws by hand.
Technical data Electricity consumption in standby: < 1.0 W Electricity consumption in networked standby: < 1.4 W Frequency band of the WiFi module 2.4000 GHz – 2.
Conformity declaration Miele hereby declares that this coffee machine complies with Directive 2014/53/EU. The complete text of the EU declaration of conformity is available from one of the following internet addresses: - Products, Download from www.miele.co.uk - For service, information, operating instructions etc: go to www.miele.co.uk/domestic/ customer-information-385.
Copyrights and Licences Miele uses their own and third party software which is not subject to any so-called Open Source Licence for the operation and control of the appliance. This software/ these software components are protected by copyright. The copyright powers of Miele and third parties have to be respected. Furthermore, this appliance contains software components which are distributed under Open Source licence conditions.
United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW Tel: 0330 160 6600, Internet: www.miele.co.uk/service, E-mail: info@miele.co.uk Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield, VIC 3180 Tel: 1300 464 353 Internet: www.miele.com.au China Mainland Miele Electrical Appliances Co., Ltd. 1-3 Floor, No. 82 Shi Men Yi Road Jing' an District 200040 Shanghai, PRC Tel: +86 21 6157 3500 Fax: +86 21 6157 3511 E-mail: info@miele.
CVA 7840 en-GB M.-Nr.