Operating instructions Cooker hoods DA 262 i DA 272 i DA 292 i In order to protect yourself and avoid damage to your machine, it is absolutely necessary to read the operating instructions prior to installation and operation. ]ö M.-Nr.
Description of the appliance Description of the appliance 1 2 3 DA 262 i 4 5 6 8 7 DA 272 i / DA 292 i 4 2 5 6 7 8
Description of the appliance Description of the appliance The cooker hood is suitable for . . . d - Slide switch for ,,Power selection“ . . . Air extraction: Air is drawn in through the grease filter f, cleaned and directed outside. . . . Air recirculation: Air is drawn in through the grease filter f and then through the active charcoal filters for cleaning. It is passed back into the kitchen through the top of the kitchen cabinet.
Contents Contents Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Help to protect our environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Cleaning and care . . . . . . . . . . .
Help to protect our environment Help to protect our environment Disposal of packaging The transport and protective packing is mostly manufactured from the following re-usable materials: . . . Corrugated paper / cardboard mostly from recycled materials. . . . CFC-free molded polystyrene. . . . Polyethylene foil (PE) partly from secondary raw materials. Disposal of your old machine Old machines contain materials which can be recycled.
Warning and Safety instructions Warning and Safety instructions Read these Operating Instructions carefully before installing or using the Exhaust Hood. This appliance is intended for residential use only. Use the appliance only for its’ intended purpose. The manufacturer cannot be held responsible for damages caused by improper use of the hood. Read all the instructions before installing or using for the first time.
Warning and Safety instructions Never connect an exhaust hood to an active chimney, dryer vent, vent flue, or room ventilating ductwork. Seek professional advice before connecting an exhaust hood vent to an existing, inactive chimney or vent flue. Do not place this exhaust hood over cooktops burning solid fuel. Never operate gas burners without pots. Heat generated by prolonged operation of gas burners without pots could damage the hood. Do not use the exhaust hood without the grease filters in place.
Warning and Safety instructions Warning and safety instructions Disposal of discarded appliances Before discarding an old appliance, disconnect its power cord to prevent it from becoming a hazard. SAVE THESE INSTRUCTIONS AND REVIEW THEM PERIODICALLY Throughout the manual, important safety items will be highlighted in boxes and should be read in conjunction with these “Warning and Safety instructions”.
Operation Operation After cooking If, after finishing cooking, there are still cooking vapors in the kitchen, it is recommended that the cooker hood be left on for some minutes longer. Then switch the cooker hood off by: moving the slide switch for the fan and the cooktop illumination switch to the ”0“ position. Pull out the deflector plate. Drop down the front control panel or lightshield. or push the deflector plate in. Set the slide switch for the fan to position ”l“.
Cleaning and care Cleaning and care Before any cleaning or maintenance work, the extractor must be disconnected from the mains supply (switch off at the wall socket and remove plug or the fuse). Cleaning The cooker hood housing may be cleaned using hot water to which a little mild detergent has been added. Dry with a soft cloth. Never use a cleaner which scours or contains chlorine, acids or soda. These would damage the surface of the cooker hood.
Cleaning and care Cleaning and care When removing the filters for cleaning, also clean off any residues of oil or fat from the filter housing to prevent the risk of these catching fire. DA 272 i, DA 292 i only: Put the filters back together. When re-inserting the filters ensure that the locking device faces down towards the cooktop. If a filter is inadvertently replaced the wrong way a round, use a small screwdriver blade to unlock the filter through the slots.
After Sales Service After Sales Service In the event of any fault which you cannot correct yourself please contact Your Miele Dealer or The Miele Service Department The address of the nearest Service Department is given on the back page. When contacting the Service Department, please quote the Model and Serial No. of the appliance, both of which are shown on the data plate. This is visible after removing the rear grease filter.
Electrical connection Electrical connection For CDN only: The cooker hoods are supplied with a 1.50 m power supply cable ready for connection to an a.c. single phase 120 V / 60 Hz supply. Caution: Ensure that power supply is OFF during installation.
Technical data Technical data Total rated load Light Voltage Frequency Fuse rating Connection cable with plug Maximum air throughput: Air extraction Air recirculation 14 DA 262 i DA 272 i DA 292 i 225 W 15 W 120 V 60 Hz 15 A 5 ft (1,5 m) 223 W 13 W 120 V 60 Hz 15 A 5 ft (1,5 m) 235 W 16 W 120 V 60 Hz 15 A 5 ft (1,5 m) 90-325 CFM (150-550 m3/h) 90-325 CFM ( 150-550 m3/h) 90-325 CFM (150-550 m3/h) 50-240 CFM (80-350 m3/h) 50-240 CFM (80-350 m3/h) 50-240 CFM (80-350 m3/h)
Installation Installation For installing the cooker hood, a cabinet is required. The minimum cabinet width required for each model is given below: – DA 262 i = 600 mm (23 5/8") – DA 272 i = 700 mm (21 9/16") – DA 292 i = 900 mm (35 7/16") The exhaust connection must be made by a suitably qualified and competent person. The distance between the top of the cooktop and the bottom of the cooker hood should be at least: 45 cm (18") above electric cooktops 65cm (26") above gas cooktops.
Installation Installation Appliance dimensions Wall unit dimensions A: DA 262 i = 560; DA 272 i = 660; DA 292 i =860 B: DA 262 i = 595; DA 272 i = 695; DA 292 i =895 5 15 ˝ /16˝ 415 /16 6 5/8˝ 2˝ 13/16˝ 1313/16˝ 25/16 ˝ 10 7 /16˝ A: DA 262 i = 22 1/16’’; DA 272 i = 26’’; DA 292 i =33 7/8’’ B: DA 262 i = 23 5/8’’; DA 272 i =27 9/16’’; DA 292 i=35 7/16’’ A: DA 262 i = 562-568 = 22 1/8" - 22 3/8" DA 272 i = 662-668 = 26 1/16" - 26 5/16" DA 292 i = 862-868 = 33 15/16" - 34 3/16" B: DA 262 i = 600 = 2
Installation Installation Building in Take the dividing wall out of the wall unit. Push the brackets into the slots on the sides of the cooker hood. 19 mm ( 3/4 ") thick side walls: Secure the support tracks to both interior walls of the unit using two 3,5 x 16 mm ( 5/8 ") screws, position as illustrated. 16 mm ( 5/8 ") thick side walls: Fasten the brackets in place on the cooker hood using the M 6 x 10 mm hexagonal bolts and washers. The thickness of the side walls must be taken into account.
Installation Installation Lift the cooker hood into the unit from below until the lugs of the brackets lie above the support tracks. Then carefully lower the cooker hood. The lugs engage with the support track. Feed the air extraction or air re-circulation connector through as applicable, (see chapter ”Air extraction“ / ”Air re-circulation“). Replace the dividing wall in the wall unit. Pull the deflector plate out to its limit and remove the grease filters.
Installation Installation Attach the spacer bar to the guide rail (2) located behind the light tube. Fitting the light tube cover – DA 262 i Pull off the transit strips on each side. Fitting the cover caps For cooker hoods without a front panel or lightshield: Position the light tube cover and screw into place (see diagram). – DA 272 i, DA 292 i Attach the extension pieces supplied to the light tube cover, then position the now extended light tube cover and screw into place.
Installation Installation Only use the template for lightshields with the following lengths: b c d e f Pull out the snap fittings from the slots on the left and right hand sides of the deflector plate (1). Press the baffle (2) into the engaging point. Put the snap fittings back in place. The snap fitting with the hole must be inserted on the right. Do not wipe off any lubricant. Hold the template supplied against the back of the lightshield and mark the drill hole positions for fixing the hinges.
Installation Fitting the front facia panel / lightshield Dismantling Disconnect the appliance from the electricity supply by unplugging at the socket, or removing the mains fuse. Take the dividing wall out of the wall unit. Release the hose clip from the exhaust connection and push the hose upwards. Screw the hinges (2) supplied to the left and right hand sides of the front facia panel / lightshield (1). With the Miele aluminium lightshield the screws are supplied.
Air extraction Air extraction Danger of toxic fumes. Please heed the ,,Warning and Safety Instructions“ to avoid the dangers of toxic fumes. The cooker hood should be installed according to local building regulations. Seek approval from the building inspector where necessary. Connection for extraction – The extraction ducting should be as short and straight as possible. – To ensure efficient air extraction the diameter of the exhaust ducting should not be less than 125 mm (5").
Air extraction Air extraction Measure the total length of the exhaust ducting to be used. Add the appropriate length of additional piping to this figure (see table), according to the number and type of bends: Type of bend Push the ducting on to the cooker hood exhaust connector or on to the reducer (adaptor) and secure. Note If the exhaust ducting is to run through rooms, ceiling space etc.
Air recirculation Air recirculation If site conditions are not suitable for the cooker hood to be used for air extraction, the appliance must be converted for recirculation. Connection The following parts are necessary for this, available from your Miele Dealer or from the Miele Spare Parts Department: Conversion kit from extraction to recirculation (Ø 125 mm, 5") Active charcoal filter Place the hose with the directional grill on to the exhaust connection of the cooker hood.
Alteration rights reserved / 44 / 001 CDN, USA - 1998 This paper is made from 100% chlorine-free bleached cellulose and therefore protects the environment.