Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. DGC 6700 DGC 6800 To prevent accidents and appliance damage read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS ,WARNING - Read all instructions before installation or use of the steam oven to prevent injury and machine damage. ~ Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubt. ~ Be certain your appliance is properly installed and grounded by a qualified technician.
Installation reference Dimension details of the appliance front * Appliances with glass front ** Appliances with metal front 151
Installation reference Control panel swivel range 152 The area in front of the control panel must not be blocked by anything (such as a door handle) this would hinder the control panel from opening and closing.
Appliance and installation dimensions Wall cabinet installation a Combi Steam Oven b Installation niche c Power supply to the appliance d Recommended location for electrical connection e Power cord * Appliances with glass front ** Appliances with metal front 153
Appliance and installation dimensions Cut-outs for venting the Combi Steam Oven To ensure that the Combi Steam Oven has adequate ventilation, the following cut-outs measuring 19 11/16" x 1 9/16" (500 x 40 mm) must be made: a in the top of the cabinet b in the center shelf above the installation niche The cabinet housing must not have a back panel fitted behind the installation niche.
Appliance and installation dimensions Undercounter installation If the appliance is to be installed under a cooktop, observe the instructions for installation of the cooktop and its installation height.
Appliance and installation dimensions Cut-outs for venting the Combi Steam Oven To ensure that the Combi Steam Oven has adequate ventilation, the following cut-outs measuring 19 11/16" x 1 9/16" (500 x 40 mm) must be made: a in the appliance support base b in the bottom of the cabinet space below The cabinet housing must not have a back panel fitted behind the installation niche.
Appliance and installation dimensions Installation in combination with an oven a Combi Steam Oven b Installation niche c Power supply to the appliance d Recommended location for electrical connection e Power cord f Oven * Appliances with glass front ** Appliances with metal front 157
Appliance and installation dimensions Cut-outs for venting the Combi Steam Oven To ensure that the Combi Steam Oven has adequate ventilation, the following cut-outs measuring 19 11/16" x 1 9/16" (500 x 40 mm) must be made: a in the top of the cabinet b in the center shelf above the installation niche The cabinet housing must not have a back panel fitted behind the installation niche. Cut-out for venting the oven: Please refer to the installation instructions for the oven.
Appliance and installation dimensions Installation in combination with ESW 6x14 a Combi Steam Oven b Installation niche c Power supply to the appliance d Recommended location for electrical connection e Power cord f Warming drawer * Appliances with glass front ** Appliances with metal front 159
Appliance and installation dimensions Cut-outs for venting the Combi Steam Oven To ensure that the Combi Steam Oven has adequate ventilation, the following cut-outs measuring 19 11/16" x 1 9/16" (500 x 40 mm) must be made: a in the top of the cabinet b in the center shelf above the installation niche The cabinet housing must not have a back panel fitted behind the installation niche.
Installing the appliance ^ Push the appliance into the installation niche and align it. The appliance must be level, so that the steam generator can operate properly. Deviation from the horizontal should not exceed 2°. ^ Secure the appliance to the left and right side of the cabinet with the two supplied 1/8" x 1" (3.5 x 25 mm) wood screws.
Electrical connection ,CAUTION: Before installation or servicing, disconnect the power supply by either removing the fuse, shutting off the main power or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous.
After sales service In the event of a fault which you cannot correct yourself please contact the Miele Technical Service Department at the phone numbers listed on the back of this booklet. When contacting the Technical Service Department, please quote the model and serial number of your appliance. These are shown on the data plate.
Copyrights and Licenses For the operation and control of the appliance, Miele uses software. The copyright powers of Miele and other software vendors concerned (e.g. Adobe) are to be respected. Miele and its suppliers reserve all rights to the software components. Specifically prohibited are: – Reproduction and distribution, – Production of changes and derived items, – Decompilation, reverse engineering, disassembly and otherwise reducing the software.
Caring for our environment Disposal of packing material Disposal of an old appliance The transport and protective packing materials are environmentally friendly for disposal and may be recyclable. Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Ensure that any plastic wrap is disposed of safely and kept out of the reach of children.
166
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
DGC 6700 / DGC 6800 en - US, CA M.-Nr.