Operating Instructions Advanta Series G 2170 Inspira Series G 1180 G 2180 To prevent accidents and machine damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Guide to the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Caring for the environment . . . . . . . . . . . . .
Contents Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Technical faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Problems water intake/drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 General problems with the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Sounds . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS WARNING – When using your dishwasher, follow basic precautions, including the following: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. The manufacturer cannot be held responsible for damage or injury caused by improper use of this appliance. Use the dishwasher only for its intended purpose. This appliance is intended for residential use only.
IMPORTANT SAFETY INSTRUCTIONS Installation ~ , WARNING - Fire hazard ~ The dishwasher must be installed Do not cover or crush the plug of the appliance. Ensure that the cabinet opening for the dishwasher provides ample space for the plug. Installing the dishwasher in a tight space may crimp the power cord or put pressure on the plug which could cause overheating. and connected in compliance with the installation instructions.
IMPORTANT SAFETY INSTRUCTIONS Use ~ Only use detergents and rinse aids ~ To reduce the risk of injury, do not recommended for residential dishwashers. Keep all detergents and rinse aids out of the reach of children. allow children to play in, on or near the dishwasher. Do not inhale or swallow detergents. ~ Only use the dishwasher if all panels ~ Dishwasher detergents contain irritant are properly in place. ~ Do not tamper with the controls.
Guide to the dishwasher Guide to the dishwasher a Upper spray arm (not visible) f Lower spray arm b Cutlery tray (depending on model) g Filter combination c Upper basket h Data plate d Middle spray arm i Rinse aid reservoir e Air inlet for drying (depending on model) j Detergent dispenser 7
Guide to the dishwasher Control panel a Check / Refill indicators d On button g / Indicator b Program selection e Off button o c Program button 8
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption and the gentlest washing of china and crystal, connect the dishwasher to a cold water source. ^ For fastest possible wash times, yet higher energy consumption, connect the dishwasher to a hot water source. ^ Make full use of the baskets without overloading for the most economical washing.
Before using for the first time To open the door To close the door ^ Push the baskets in. ^ Lift the door and push until it clicks into position. ^ Pull the handle to open the door. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will continue.
Before using for the first time Rinse aid Rinse aid is needed to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. ,Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using "2 in 1" detergents, no rinse aid is needed.
Before using for the first time Rinse aid indicator Adjusting the dosage When the Rinse aid indicator first comes on, there will be enough rinse aid left for 2 - 3 washes. The dosage selector is preset to 3. This dispenses approximately 3 ml of rinse aid per program. It can be adjusted from 1 to 6. – Use a higher setting if spots appear on dry glassware. – Use a lower setting if streaking appears on dishes or glasses. ^ Turn the dishwasher off o.
Before using for the first time The amount set can be recognized by the flashing rhythm of the upper right indicator (see table). Rinse aid amount Flashing rhythm in ml 0 – 1 Once 2 Twice 3 Three times 4 Four times 5 Five times 6 Six times ^ Press the program button until the upper right program indicator lights. ^ Select the desired setting with the program button. Every touch of the button increases the level. The programmed dosage is saved. ^ Turn the dishwasher off o.
Loading the dishwasher ,Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher. Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher. Wax, grease and paint will cause permanent discoloration and damage to the dishwasher. ^ Scrape food from dishes before placing them in the dishwasher, rinsing is not necessary. ^ Some foods contain natural dyes, e.g. carrots or tomatoes.
Loading the dishwasher Items not recommended for dishwashing – Cutlery with wooden handles – Wooden cutting boards – Glued items such as old knives with handles glued together around the shank of the blade – Handmade craft items, antique, metal trimmed or decorative glassware Glassware: – There are no standard guidelines for washing glassware, when in doubt wash by hand. – When purchasing new dishes, glasses and cutlery, make sure they are dishwasher safe.
Loading the dishwasher Cutlery tray (depending on model) Spoons with thick handles may have to be placed as knives and forks with their heads in the holders ^ Arrange the cutlery as shown in the cutlery tray. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge down and forks with the prongs between the holders.
Loading the dishwasher Cutlery basket Spoon inserts for the cutlery basket (depending on model) The supplied insert is designed to wash heavily soiled spoons. The individual slots allow the water to better reach the surface of each spoon. ^ For best cleaning results, cutlery should be placed in the basket with the handles down. Knives and forks should be loaded with the pointed end down to prevent injuries. ^ Attach the insert when needed to the cutlery basket.
Loading the dishwasher Upper basket ,Always use the dishwasher with the upper and lower basket inserted. Cup racks ^ Raise the rack to make room for tall glasses. Lower it to double stack smaller pieces. Coffee bar (depending on model) Glasses can be leaned against the coffee bar for a secure stand. ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls and flat pans.
Loading the dishwasher Adjusting the upper basket The upper basket can be raised or lowered to accommodate tall items. The basket can also be angled to fit tall items in both, the upper and lower baskets. The angles should not be set to opposite extremes. This will block the middle spray arm. Take care when sliding the basket in and out in this position. Depending on the setting of the upper basket, a variety of plate dimensions can be accommodated.
Loading the dishwasher Lower basket Foldable spikes ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Two rows of spikes can be folded down, to create more room for larger dishware, e.g. pots, pans and bowls. Dishwashers with cutlery tray ^ Lift the spike rows and fold them down on one another.
Loading the dishwasher Vase/Bottle holder (depending on model) The vase/bottle holder, e.g. for vases and baby bottles, can be inserted into the lower basket as shown in the illustration. If placed anywhere else, water will not reach all surfaces. The bottle will not be properly cleaned.
Basket accessories Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele. Depending on the model some accessories come standard with the machine.
Use Detergent ,Dishwasher detergents contain irritant and corrosive ingredients. Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Fill the detergent dispenser only when you are ready to start the dishwasher. You can use powder, gel or tab detergents. Follow the dosage information on the detergent packaging. Detergent tabs are not recommended for use with the program "Short". The tabs may not dissolve completely.
Use Adding detergent ^ To open, press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. The horizontal marks in compartment II indicate the levels of approximately 1 ¼ and 2 tablespoons (20 and 30 ml) respectively. Compartment I holds a maximum of 2 teaspoons (10 ml).
Use Turning on Starting a program ^ Open the water supply, if it is closed. ^ Select the desired program with the program selector button. ^ Open the door. ^ Make sure the spray arms can rotate freely. ^ Turn the dishwasher on g. The indicator g lights. Selecting a program Choose your program according to the type of load and soiling. The indicator of the selected program lights. ^ Close the door. The program starts. Cancel a program only in the first 5 minutes.
Program guide Program When to use Program sequence Main wash Prerinse 1 Pots & Pans For normally soiled pots and pans with dried on food, also for heavily soiled dishware, use 120% of normal detergent dose Run-time 125 min Normal For normally soiled dishware Run-time 129 min Economy 2 Interim rinse 1 2 Final rinse Drying x x x x x x x x x x For normally soiled dishware, energy saving program with a long soaking time and a low temperature Run-time 95 min x x x x SaniWash Extende
Use At the end of a program Interrupting a program ^ Open the door a few inches to see if the program has finished. A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. The indicator of the selected program has gone out. As long as the program indicator is still on, the program is still running. Close the door again to allow the program to finish. Dishes tends to chip if removed still hot from the dishwasher.
Additional functions Buzzer The end of a program and faults can be announced by a buzzer tone. The buzzer at the end of a program sounds five times in intervals with a brief break in between. The buzzer sounds up to one hour if the dishwasher is not turned off. The buzzer for a fault sounds continuously. The buzzer sounds for up to two minutes if the dishwasher is not turned off or the fault is fixed. The buzzer is activated by default. It can be set to off, so it does not sound at the end of a program.
Additional functions Factory default All settings can be reset to the factory default. ^ Open the door. ^ Turn the dishwasher off o. ^ Press the program button and at the same time turn the dishwasher on g. Hold the program button until the lower right program indicator comes on. If it does not come on, start over. ^ Press the program button 12 times. The "Intake/Drain" indicator flashes once long and twice short in intervals. The upper right program indicator shows if a setting was changed.
Frequently asked questions With the aid of the following guide, minor problems can be fixed without a service call. ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Issue The program does not start. The dishwasher stops during a program. 30 Possible fault The door is not properly closed. The machine is not plugged in. The fuse has tripped.
Frequently asked questions Issue Possible fault Solution The buzzer sounds. All program indicators flash when the door is open. There may be a technical fault. – Turn the dishwasher off o. After a few seconds: – Turn the dishwasher on. – Select the desired program with the program selector button. – Close the door. If the problem persists, call Technical Service. – Turn off the water supply. – Call Miele Technical Service. The drain pump is The waterproof system running when the door has activated.
Frequently asked questions Problems water intake/drain Issue Shortly after the program start the program stops. The buzzer sounds. The "Intake/Drain" indicator flashes and lights alternately when the door is open. The dishwasher stops, the buzzer sounds and the "Intake/Drain" indicator flashes when the door is open. Possible fault The water supply is closed. Before fixing the fault: – Turn the dishwasher off o. Fault in the water intake. Fault in the water drain. There may be water in the wash cabinet.
Frequently asked questions General problems with the dishwasher Issue Detergent is left in the dispenser at the end of a program. The detergent lid cannot be closed properly. The door and the interior walls are still wet after a program has finished. Water remains in the wash cabinet at the end of a program. Possible fault Solution The dispenser was damp Dry the dispenser before when detergent was added. adding detergent. Detergent residue is blocking the catch. Remove the residue.
Frequently asked questions Sounds Issue There is a knocking noise in the wash cabinet. There is a rattling noise in the wash cabinet. There is a knocking noise in the water pipes. 34 Possible fault Solution The spray arm is hitting an Interrupt the program, item in the basket. rearrange items blocking the spray arms. Items are not secure in the Interrupt the program and wash cabinet. rearrange loose pieces. This may be caused by This has no effect on the the installation or the dishwasher.
Frequently asked questions Poor cleaning results Issue Possible fault The dishes are not The dishes were not loaded clean. correctly. The program was not powerful enough. Not enough detergent was dispensed. The spray arms are blocked by items. The triple filter in the base of the wash cabinet is not clean or not correctly inserted. The spray arm jets might be clogged. The drain pump or the non-return valve is blocked. Wash water will run back into the wash cabinet. Glasses and cutlery show streaks.
Frequently asked questions Issue Possible fault Dishes are still wet, glasses and cutlery are spotted. The rinse aid setting may be too low, or the rinse aid reservoir is empty. White residue is visible on cutlery and dishes. Clouding occurs on glassware and film can be wiped off. 36 Solution Increase the dosage, refill the reservoir or switch the rinse aid product when refilling, see "Before using for the first time". Dishes were taken out too Leave dishes in longer, see soon. "Use".
Frequently asked questions Issue Possible fault Glasses are discolored and the film cannot be wiped off. Glasses are dull and discolored, film cannot be wiped off. Detergent ingredients have Use a different detergent. been deposited on the glassware. Tea or lipstick stains have not been completely removed. The wash temperature of the selected program was too low. The detergent has a low bleaching effect. Natural dyes e.g. from vegetables may be the cause.
After sales service Repairs MieleCare In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. MieleCare, our Extended Service Contract program, gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts.
Transport To transport the dishwasher, e.g. when moving to a new home, note the following: – Empty the dishwasher. – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – Transport the dishwasher in the upright position. If unavoidable it may be transported on its back. Do not transport it on its side or on the door. Residual water in the machine could leak and cause electrical damage.
User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use.
Cleaning and Care Cleaning the control panel Check your dishwasher regularly (approx. every 4-6 months). This will help avoid faults and problems. Cleaning the wash cabinet ,Do not use abrasive cleaning agents, glass cleaning agents or all-purpose cleaners. They will damage the surface. Generally, the wash cabinet is self cleaning if the correct amount of detergent is used. ^ Only clean the control panel with a damp cloth.
Cleaning and Care Triple filter system The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones). ,The machine must not be used without all the filters in place! ^ Check and clean the filter system every 4-6 months or whenever a foreign object is trapped.
Cleaning and Care To clean the inside of the filter, the flap must be opened. ^ Return the filter so it lies flat in the base of the wash cabinet. ^ Push the clips together a and open the flap b. ^ Lock the filter by turning the handle clockwise. ^ Rinse under running water. ,The triple filter system must be ^ Close the flap so that the clip engages. inserted and locked. Large particles could get in the circulation system and cause a blockage.
Cleaning and Care Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). ^ Press the top spray arm up to engage the inner ratchet and unscrew the spray arm. ^ Lift up the middle spray arm, a, to engage the ratchet and unscrew the spray arm, b. ^ Remove the lower basket.
Cleaning and Care Cleaning the water inlet filter A filter is incorporated into the intake hose attached to the dishwasher’s shut off valve. If your water is hard or the pipes contain sediment, this filter may clog and prevent enough water from entering the wash cabinet. ,The plastic housing of the water connection contains electrical wiring. Do not submerge the housing in liquid. Do not cut the intake hose or submerge it in liquid.
Cleaning and Care Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system"). ^ Use a jug or bowl to scoop water out of the wash cabinet. The drain pump is beneath the non-return valve (see arrow). ^ Remove all foreign objects from the drain pump (glass or bone splinters).
Installation Instructions For installation of the dishwasher please refer to the Installation Sheet supplied with these instructions.
Help to protect the environment Disposal of the packing material The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! 50 Disposal of an old machine Old appliances may contain materials that can be recycled.
Electrical connection ,Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held responsible for unauthorized work. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the mains. Danger of overheating! See data plate on the right side of the door.
Plumbing Connection to the water supply ,Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperature required by the wash program. This allows for connection of the machine to either a hot or cold water source. For lowest energy consumption connect the dishwasher to a cold water source. For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source. All programs use hot water in the rinse cycles.
Plumbing Drainage Venting the drainage system – The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. If the dishwasher drain hose is connected to a floor drain or to a drain pipe that is less than 8" (20 cm) above the floor, the drain must be vented. Otherwise the water inside the dishwasher may siphon out during the wash program. – The dishwasher is equipped with a 5 ft (1.
Alterations reserved/4906 G 1180 / G 2170 / G 2180 / For the most updated manual see the Miele website. M.-Nr.