Installation Instructions CS1421 S en - CA Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions.
Safety instructions and warnings Correct use WARNING- When using your appliance follow basic precautions, including the following: Read all instructions before installation or use to prevent injury and appliance damage. This appliance conforms to all uniform safety codes and regulations. The manufacturer cannot be held responsible for damage or injury caused by improper use of this appliance. ~ The grill is intended for household use only, as described in these instructions.
Safety instructions and warnings Children ~ Always supervise any children in the vicinity of the appliance. Do not allow children to play with the unit. ~ Children should use the grill only if they have received sufficient instruction to operate it safely. They must be able to understand and recognize the potential hazards of improper operation. ~ Take special care that children do not put their fingers under the retracting browning unit. There is a risk of injury. .
Safety instructions and warnings Technical safety ~ Only skilled persons duly authorized by the manufacturer may install this appliance or perform maintenance and repair work on it. Work performed by unqualified persons carries the risk of serious harm to the user, for which the manufacturer will not be held liable. ~ Before installation, check the appliance for visible signs of external damage. NEVER under any circumstances operate a damaged appliance. It may endanger your safety.
Safety instructions and warnings ~ Repair of the appliance during the warranty period should be performed only by Customer Service personnel who are duly authorized by the manufacturer; otherwise any damage will not be covered by the warranty. ~ Before any maintenance or repair Correct use ~ The appliance becomes hot during use and remains so for some time after being switched off.
Safety instructions and warnings ~ Do not set up or operate the appliance in the open air. ~ Do not use the ledge for storage. If the appliance is accidentally switched on or there is residual heat, there is the danger that any items located there will heat up and melt, depending on the materials involved, and generating a risk of fire and burns. ~ Do not keep heat-sensitive items in proximity to the appliance. The appliance radiates heat during operation.
SAFETY INSTRUCTIONS FOR INSTALLATION Note to the installer: Please leave this instruction book with the consumer for the local electrical inspector’s use. The minimum distances given in these Installation Instructions must be observed in order to ensure safe operation. Failure to do so increases the risk of fire. The cabinetry and venting hood should be installed first to prevent damage to the cooktop.
SAFETY INSTRUCTIONS FOR INSTALLATION Safety distances above the appliance If there is more than one appliance beneath a hood (e.g. wok burner and electric cooktop), and they have different minimum safety distances always observe the greater distance. The minimum distance between the appliance and an installed exhaust hood must be at least 25 9/16" (650 mm). However, if the hood manufacturer requires a larger distance, the larger distance takes precedence.
SAFETY INSTRUCTIONS FOR INSTALLATION Safety distances to the sides of the appliance The appliance should only be installed as shown in the illustrations, while maintaining the required safety distances shown. Do not install the appliance between two tall cabinets, this is a fire hazard. A distance of alteast 2" (50 mm) must be kept between the countertop cut-out and the rear wall because of the high temperatures radiated.
Installation Installation dimensions a Spring clips b Appliance front c Installation height d Power supply box with connection cable, L = 78 3/4" (2000 mm) e Browning unit, height-adjustable 21
Installation Cut out ^ Make the worktop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the appliance(s). See also "SAFETY INSTRUCTIONS FOR INSTALLATION". ^ Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture. The materials used must be heat resistant.
Installation Installation of multiple appliances When installing more than one combiset appliance, a support bar b must be installed between the appliances. Countertop cut-out two appliances D Countertop cut-out three appliances D 50 50 0 0 b b C A For the installation of two appliances the width of the countertop cut-out D is the sum of A and C.
Installation Sample calculations for a countertop cut-out for three appliances 24 A appliance width minus 5/16" (8 mm) B appliance width C appliance width minus 5/16" (8 mm) D Countertop cut-out 11" (280 mm) 11 5/16" (288 mm) 11" (280 mm) 33 3/8" (848 mm) 11" (280 mm) 15" (380 mm) 14 5/8" (372 mm) 40 5/8" (1032 mm) 11" (280 mm) 22 11/16" (576 mm) 22 3/8" (568 mm) 56 1/16" (1424 mm) 14 5/8" (372 mm) 11 5/16" (288 mm) 11" (280 mm) 37" (940 mm) 14 5/8" (372 mm) 15" (380 mm) 14 5/8" (372
Installation D 25-30 50 50 50 25-30 50 50 0 a a a b c c a a a A 68 72/5 80/3 B 576 380/ 8 28 / C 68 72/5 80/3 2 2 a Spring clips b Support bars c Space between support bar and countertop An additional support bar is required for each additional appliance. The position for attachment of an additional spacing strip depends on the width of the appliance B.
Installation Attach the spring clips and support bars Wood or solid surface countertops Granite countertop 25-30 25-30 a c a c b ^ Place the supplied spring clips a and the support bars b at the marked positions as shown above, by laying them on the upper edge of the cut-out and then securing them with the 1/8" x 1" (3.5 x 25 mm) screws (supplied). 26 b ^ Position and attach the spring clips a and support bars b with strong, double-sided tape c. The screws are not needed for granite countertops.
Installation a ^ Coat the edges of the spring clips a, d b ^ and the space d between the strips b and the countertop with silicone (supplied).
Installation Installing the appliance ^ Feed the power cord down through the cut-out. ^ Then place the front side of the appliance in the countertop cut-out. ^ Then with a hand on each side of the appliance press down evenly on the edges until it clicks into position. When doing so make sure that the appliance seal sits tightly on the countertop to ensure it is sealed correctly. Do not permanently seal into the countertop. ^ Connect the appliance to the main power supply.
Installation Sealing Tiled surfaces The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. The grouting a and shaded area under the appliance frame must be flat and even, so that the frame will lie evenly and the sealing strip under the edge of the upper part of the appliance can provide an adequate seal against the countertop.
Electrical connection ,CAUTION: Before installation or servicing, disconnect the power supply by either removing the fuse, shutting off the main power supply or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer will not be held responsible.
Alteration rights reserved / 4608 For the most updated manual see the Miele web site. M.-Nr.