Operating and Installation Instructions Built-in Warming Drawer ESW 408x-14 ESW 47xx ESW 48xx To prevent accidents and machine damages, read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Guide to the warming drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ESW 408x-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ESW 47xx / ESW 48xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control panel . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS Correct usage WARNING- When using your appliance follow basic precautions, including the following: Read all instructions before installation or use to prevent injury and appliance damage. This appliance conforms to all uniform safety codes and regulations. Keep these operating instructions in a safe place and pass them on to any future user. SAVE THESE INSTRUCTIONS ~ This appliance is not designed for commercial use.
IMPORTANT SAFETY INSTRUCTIONS Technical safety ~ Before installing the appliance, check for externally visible damage. Do not operate a damaged appliance. ~ Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond in order to avoid risk of damage to the appliance. If in doubt, consult a qualified technician. ~ Be certain your appliance is properly installed and grounded by a qualified technician.
IMPORTANT SAFETY INSTRUCTIONS Safety ~ Protect your hands with oven mitts or potholders when using the appliance. Use only dry, heat resistant potholders. Moist or damp potholders used on hot surfaces can result in steam burns. ~ Be aware of loose fitting or hanging clothing while using the warming drawer. They may present a fire hazard. ~ Do not heat unopened food containers. Pressure can build up causing an explosion that will damage the cooking compartment.
IMPORTANT SAFETY INSTRUCTIONS ~ The use of accessories not recommended by Miele may cause injury. ~ Make certain that the power cords of small appliances do not come in contact with the appliance. The insulation of the cable could become damaged. Danger of electric shock! ~ Do not lean, sit or overload the warming drawer. This will cause damage. The drawer can hold a maximum of 55 lbs (25 kg). ~ Do not use plastic containers, plastic wrap or aluminum foil in the warming drawer.
Guide to the warming drawer ESW 408x-14 a Control panel b Non-slip mat 7
Guide to the warming drawer ESW 47xx / ESW 48xx a Control panel b Non-slip mat c Vent d Rack 8
Guide to the warming drawer Control panel On/Off Turns the warming drawer On and Off Menu Allows you to select the operating mode Operating modes: / Cups/glasses H Tableware 2 Food - warm and hold Temp. Allows you to select the desired temperature. The display shows: ]^^^^ See "Temperature settings" for more information. Timer Allows you to set the heating time.
Before the first use When first connecting the appliance to the power supply and after a power failure, the fan will run and a display test will be carried out for approx. 10 seconds. The appliance cannot be used during this time. Clean the appliance ^ Remove any protective wrapping. ^ Remove the non-slip mat and clean with a solution of warm water and liquid dish soap. Dry with a soft cloth. ^ Clean the warming drawer, inside and out, with a damp cloth and wipe dry.
Using the warming drawer Operating modes Tap the "Menu" touch control until the desired operating mode lights: – / Cups/Glasses – H Tableware – 2 Food - warm and hold The last operating mode selected appears in the control panel when the drawer is turned on. The warming drawer is equipped with a fan which distributes warm air throughout the drawer. During the operating modes "Cups/Glasses" and "Tableware" the fan runs continuously. During "Food - warm and hold" it runs in intervals.
Using the warming drawer Temperature settings Each operating mode has an assigned temperature range. The suggested temperatures are set by default, they are marked in bold in the table below. Use the "Temp." touch control to change the setting in increments. The last selected temperature is shown in the control panel the next time the warming drawer is turned on.
Using the warming drawer Duration Operation The warming drawer is set for continuous operation by default. By selecting the "Timer" touch control a warming time can be set. With each tap of the "Timer" touch control the duration will increase in one hour increments, beginning with 1 hour and ending with 4 hours. Selecting "Timer" one more time (equaling 5 taps) will set continuous operating mode. ^ Open the drawer.
Using the warming drawer Sabbath Mode Activate For religious observance, the appliance can be set for the duration of the Sabbath. In Sabbath mode the timer is deactivated and the sensors have to be touched longer than ususal. If Sabbath mode is activated, the appliance will turn off after approx. 72 hours, then automatically reset to normal operation. ^ Press and hold "Timer". ^ At the same time press and hold "On/Off". ^ Hold both buttons until all 4 timer indicators light up at once.
Loading the warming drawer The drawer load will depend on the type and size of your dishes. The maximum load is 55 lbs (25 kg). Do not overload the drawer. To increase the load space use the supplied rack. Two racks will fit in the drawer at one time. Additional racks are available from Miele.
Keeping food warm Tips The warming drawer is intended for keeping food warm directly after preparation. It is not intended to re-warm cold meals. – To ensure that the minimum temperature of 150°F (65°C) required to keep food warm is met, select 2. – Preheat the warming drawer for approx. 15 minutes to guarantee that the interior has risen to the desired temperature. – Place food into preheated tableware before placing into the warming drawer.
Keeping food warm Settings Food Type of container Lid on container Temperature for 2 setting Position in drawer Floor Rack* Bacon Plate no ^^]^^ x x Beef** Rare / Medium / Well Pan yes ]^^^^ x x Bread hard rolls Plate no ^^^^] x x Plate yes ^^^^] x Plate / Casserole dish no ^^]^^ x x Casserole, moist Pot / Dish yes ^^^^] x x Eggs, hard boiled Plate no ^]^^^ x x Scrambled eggs Bread soft rolls Casserole, crisp top Pan / Plate yes ^^]^^ x x Fish / Seafood P
Warming tableware Tips Warming times – Distribute tableware throughout the entire drawer. Stacked plated will heat up more slowly than individual pieces. If stacking is unavoidable please them in the front of the drawer. Use the rack (depending on model). Various factors will affect the warming times of tableware: – Do not place platters right up against the vents. They may cover the warm air outlets, causing the tableware to not heat evenly.
Other usages The warming drawer can also be used to proof yeast dough or to warm or crisp bread. Proofing dough Warming/Crisping bread ^ Open the drawer. ^ Open the drawer. ^ Turn the appliance on "On/Off". ^ Turn the appliance on "On/Off". ^ Touch "Menu" to select the " / Cups/Glasses" setting. ^ Touch "Menu" to select the " 2 Food - warm and hold" setting. ^ Touch "Temp." to select the ] ^ ^ ^ ^ temperature setting. ^ Touch "Temp." to select the ^ ^ ^ ^ ] temperature setting.
Cleaning and care Allow the appliance to cool before cleaning. Do not use a steam cleaner to clean this appliance. Pressurized steam could penetrate electrical components and cause a short circuit. Do not use commercial cleaning agents. Only use agents recommended for domestic use. Appliance front / interior Remove spills as soon as possible. Otherwise the soiling may become hard to remove.
Frequently asked questions ,Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. What if the drawer does not heat? Possible fault Solution There is no power to the warming drawer. Insert the plug into the outlet. The circuit breaker has tripped. Reset the circuit breaker. If in doubt contact an electrician. What if the food is not warm enough? Adjust the temperature setting.
Technical Service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance. This information is visible on the silver data plate supplied with the appliance.
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and machine damage read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS ~ Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond in order to avoid risk of damage to the appliance. If in doubt, consult a qualified technician. ~ The electrical outlet should be easily accessible after installing the unit. ~ Be sure that after installation the power cord does not come into contact with any hot surfaces.
ESW 408x-14 Miele appliances can be installed flush or proud. Discuss your installation requirements with your architect, designer and installer.
ESW 408x-14 Installation with a speed oven 7/8" 6" 7/1 (5 (141 mm) " 1/8 m) 53 5 9/16" 21 7 m ( (5 219 1/8 (3 (7 mm ) mm" ) 1/4 " 48 23 6" 95 m (5 m ) (2 7/8 2* /2 " 3* *m m ) * Machine with glass front ** Machine with stainless steel front 26 " 16 ) m m 7/ /1 ) m 23 95 m (455.
ESW 408x-14 Installation with a steam oven 17 9/16" 0 ) (56 mm 8 -56 23 6" 7/1 m) m 5 59 5 9/16" (141 mm) ( " 1/8 m) 217 m 3 (5 (5 219 /1 6" (455.
ESW 408x-14 Installation with a coffee machine ) 0 (56 8 mm 6 -5 17 15/16" 17 9/16" 2 - 22 mm 6" 7/1 m) 23 95 m 5 9/16" (141 mm) (5 " 1/8 ) 21 7 mm 3 (5 " 16 219 7/ ) (5 / m 3 48 16" m 2 5 m 9 1/8 m 5 ( ) (3 " mm ) (22 7 (7 1 m /8" mm /4" m */2 ) 3 m m **) * Machine with glass front ** Machine with stainless steel front 28 (455.
ESW 408x-14 BRWS Combination possibilities Installation with an oven a 13/16" (30 m m) 217/8" 23 7/16" (596 mm) 5 3/16" 55 (134 mm) (0 5m 22- 22 m) " 3/8 22 3/4" 6" 1/1 (578 mm) 28 7/8" - 29" (734 mm - 736 mm) 7/8" (22 " 21 9/1 */23**mm 9/16 ) 21 mm) (548 m 6 7 m) (54 m 0m ) (56 8 mm 6 -5 6" 7/1 m) 23 95 m 59/16" (141 mm) (5 " 1/8 m) 21 7 m 3 (5 (5 219 48 1/8 (3 (4 mm ) mm" ) 1/8 " /1 6" m m ) (2 " 16 7/ m) 23 5 m 9 (5 /2 7/8 3* " *m m 2* ) a Cut-out for venti
ESW 408x-14 BRWS Installation with a speed oven 7 17 9/16" 22- 22 m m ) 0 (56 8 mm -56 6" 7/1 5 9/16" (141 mm) (5 " 1/8 m) 21 7 m 3 (5 (5 219 1/8 (3 (4 mm ) mm" ) 1/8 " 48 2395 6" m (5 m ) (2 7/8 2* /2 " 3* *m m ) * Machine with glass front ** Machine with stainless steel front 30 " 16 ) m m 7/ /1 ) m 23 95 m (455.
ESW 408x-14 BRWS Installation with a steam oven 7 17 15/16" m) " 3/8 17 9/16" 22- 22 m 0m ) (56 mm 8 -56 6" ) m m 7/1 23 595 5 9/16" (141 mm) ( " 1/8 m) 217 m 3 (5 (5 219 /1 6" (455.
ESW 408x-14 BRWS Installation with a coffee machine 17 15/16" 6" 7/1 m) 23 95 m 5 9/16" (141 mm) (5 " 1/8 ) 21 7 mm 3 (5 (5 1/8 (3 (4 mm ) 219 48 1/8 ) " 23 6" m m (5 ) " mm " 16 7/ ) m m 95 /1 (2 2 7/8 m m " */2 3 m m **) * Machine with glass front ** Machine with stainless steel front 32 5 3/16" " 3/8 m 0m ) (56 8 mm 6 -5 (455.
ESW 47xx Solo installation Side view a A base is required for solo installations 33
ESW 47xx Installation with an oven Side view with oven 34
ESW 48xx Solo installation Side view a A base is required for solo installations 35
ESW 48xx Installation with an oven Side view with oven 36
Installation Miele appliances can be installed flush or proud. Discuss your installation requirements with your architect, designer and installer. Check that the base of the warming drawer is clean and level. Only then will it function properly. When inserting the appliance, wear work gloves to avoid injuries. ^ Push the appliance into the cabinetry, and align. ^ Open the drawer and fix the appliance with the supplied screws at the side panels of the cabinet (see appropriate illustration).
Installation Aligning the appliance front After installation it may be necessary to align the appliance front and/or the gap between the appliances/furniture front above. ^ Remove the screws a from the left and right sides of the drawer front. ^ Carefully lift the control panel out of the drawer. Be careful not to pull or damage the power cord.
Installation ^ Loosen the 2 screws b on the inside of the drawer front. ^ Align the front. ^ Tighten the screws on the inside of the drawer front. ^ Replace the control panel, use caution with the power cord. ^ Replace the screws on the left and right sides of the drawer front.
Installation Integrated installations Custom made front panels can be installed with models ESW 4702 FB and ESW 4802 FB. The custom panel must be at least 3/8" (19 mm) thick and made of heat resistant material 140 °F (60 °C). The front panel, including handle, must not exceed 11 lb (5 kg) in weight. ^ Install a handle to the custom front panel using countersunk screws.
Installation ^ Remove the cable tie from the panel. ^ Screw the removed panel to the custom panel (see illustration). ^ Hook the panel into the bottom. Make sure the seal is seated correctly. ^ Replace and slightly tighten the screws on the inside of the drawer front. ^ Align the front. ^ Tighten the screws on the inside of the drawer front. ^ Replace the control panel, use caution with the power cord. ^ Replace and tighten the screws on to the left and right side of the drawer front.
Electrical connection ,CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous.
Help protect our environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
Alteration rights reserved / 4611 M.-Nr. 07 342 380 / 08 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
