Operating Instructions Built-in Warming Drawer ESW 700-25 ESW 760-25 ESW 761-25 To prevent accidents and machine damages, read these instructions before installation or use. UV M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the warming drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Guide to the controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Temperature selector . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS Technical safety WARNING- When using the warming drawer follow basic precautions, including the following: Read all instructions before installation or use of the warming drawer to prevent injury and machine damage. This appliance is only intended for the domestic use of holding cooked food at serving temperature. Any other use is at the operator’s own risk and could be dangerous. This appliance conforms to all uniform safety codes and regulations.
IMPORTANT SAFETY INSTRUCTIONS This appliance must only be used after it has been installed in cabinetry to ensure all electrical components are shielded. Never open the outer casing of the appliance. Tampering with electrical connections or components and mechanical parts is dangerous and can cause machine damage. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner.
IMPORTANT SAFETY INSTRUCTIONS It is possible that some bacterial growth may occur in foods maintained for lengthy periods of time at low temperature levels. Before serving, be sure food is at a safe temperature. This is particularly important when preparing food for babies and children. Never warm undiluted alcohol in the warming drawer as this can easily ignite. Exercise caution when warming food with a high sugar content. If heated for too long the sugar may caramelize or ignite.
IMPORTANT SAFETY INSTRUCTIONS General notes Children should not be left alone or unattended in an area where an appliance is in use. They should never be allowed to sit or stand on any part of the appliance. Caution: Do not store items of interest to children in cabinets above or in the warming drawer. Children climbing on the appliance to reach these items could be seriously injured. Wear proper clothing. Loose-fitting or hanging garments should never be worn while using the warming drawer.
Guide to the warming drawer a Timer b Temperature selector c Humidity control d Non-slip mat e Rack f Drawer 8
Guide to the controls The warming drawer is operated by the timer, the temperature selector and the humidity control. The controls are only visible when the drawer is open. Once the warming drawer begins to heat the circulation fan will turn on to evenly heat the drawer. When the selected temperature is reached, the heat and the fan will shut off to prevent food from drying out. Timer The timer activates the heating elements and circulation fan.
Guide to the controls Temperature selector The temperature can be set on or between the "Low", "Medium" and "High" settings.
Guide to the controls Humidity control – : This position closes the vents and seals the moisture in the drawer to keep food moist and soft. Condensation may occur around the inside edge of the drawer. – : This position opens the vents for maximum airflow to keep food crisp. "Dry" is ideal for keeping both dry and liquid foods warm, e.g. soup and bread. Cover liquids with a plate or foil to prevent evaporation. In this setting moisture may collect on surfaces above the warming drawer.
Guide to the controls Temperature And Humidity Suggestions Food Bacon 2 2 Humidity control Covered1 / Uncovered Medium Dry Uncovered Beef Medium / Well Medium Moist Covered Beef Rare Low Moist Covered Bread hard roles Medium Dry Uncovered Bread soft rolls Medium Moist Covered Bread proofing "0" Moist Damp Towel Casserole, crisp top2 Medium Center Uncovered Casserole, moist High Moist Covered Eggs Medium Moist Covered Fish / Seafood Medium Moist Covered Fish sticks
Loading the warming drawer The drawer load will depend on the type and size of your dishes. The rack can be inserted in three positions: middle, left or right. The maximum load is 33 lbs (15 kg). Do not rest heavy items on the drawer. ^ Insert the rack into the slots of the rear wall in the drawer and then slide the front of the rack into position. Use the supplied rack to increase the load space. Additional racks are available for purchase from the Technical Service Department.
Loading the warming drawer Tips – To keep different foods hot, set the temperature for the food requiring the highest temperature setting. Place the food needing the highest setting on the rack and the other food on the floor of the drawer. – For large quantities of food, it may be necessary to use a higher temperature and humidity level. – When warming food and dishes at the same time, place the dishes on the floor of the drawer and the food on the rack.
Using the food warmer Keeping food warm ^ If necessary adjust the settings. For best results, preheat the warming drawer before warming food. ^ Close the drawer. ^ Open the drawer. ^ Turn the timer to the desired time setting. ^ Turn the temperature selector to the desired temperature setting. ^ Slide the humidity control to the desired humidity level. Use the "Moist" setting when preheating. ^ Close the drawer. Keep the drawer closed while in use to prevent food from drying out.
Using the food warmer Prewarming the dishes The warming drawer can also be used to warm dishes. Do not preheat the drawer before warming dishes. Only use heat resistant dishes. ^ Open the drawer. ^ Place the dishes in the drawer. Arrange dishes evenly in the drawer and on the rack. Limit stacks to 2 plates for better warming. ^ Turn the timer to 30 minutes (halfway to "1 h"). ^ Turn the temperature selector to: "Low" if dishes are on the rack or are light weight.
Warming drawer care , CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Do not clean or remove the warming drawer until it has cooled. Danger of burns! Appliance front and control panel ^ All external surfaces and controls can be cleaned with warm water and liquid dish soap applied with a sponge. ^ Wipe dry using a soft cloth. Glass Glass surfaces can be cleaned with a glass cleaner.
Warming drawer care Drawer Non-slip mat The drawer can be removed for easier cleaning. Clean the non-slip mat by hand with warm water and liquid dish soap. Removing the drawer Only put the non-slip mat back in the drawer when it is completely dry. The non-slip mat is not suitable for cleaning in a washer or dishwasher. Rack ^ Clean the rack with warm water and liquid dish soap or a non-abrasive stainless steel cleaner. ^ Pull the drawer completely out and loosen the nuts.
Frequently asked questions ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause an injury or machine damage. Some minor problems can be fixed without a service call. What if the drawer does not heat? Possible fault Fix There is no power to the warming drawer. Insert the plug into the outlet. The circuit breaker has tripped. Reset the circuit breaker.
Technical Service In the event of a fault which you cannot easily fix yourself, please contact: – Your Miele Dealer or – The Miele Technical Service Department USA 1-800-999-1360 techserv@mieleusa.com CDN 1-800-565-6435 service@miele.ca When contacting Technical Service please quote the serial number and model of the warming drawer.
Installation Instructions
Help protect our environment Disposal of the packing materials The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! 22 Disposal of an old appliance Old appliances may contain materials that can be recycled.
Electrical connection ,CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer will not be held responsible. Power supply This appliance is equipped with a 5 ft (1.
Installation Installation tips – The warming drawer should be placed at a convenient height for easy access. – The drawer should be installed clear of drafts caused by open doors and windows. – Proper clearance must be allowed for the warming drawer to open with out interference. – The warming drawer must be secured to cabinetry to prevent the drawer from tipping when loaded. – The warming drawer should be level to prevent the drawer sliding open or closed on its own.
Appliance dimensions ESW 700-25: ESW 760-25, 761-25: 25
Installation Installing the warming drawer ^ Push the casing in the cabinetry. ^ Remove the drawer from the casing before installing the appliance in the cabinetry. Removing the drawer ^ Secure the casing in the cabinetry with the six screws. Inserting the drawer ^ Pull the drawer completely out and loosen the nuts. ^ Carefully lift the drawer and pull it slowly out. Set the drawer down on a flat, stable surface. 26 ^ Pull out the telescopic skies from the casing.
Installation Integrated installations Models 700-25 FB / 760-25 FB a Install a handle to the custom front panel using counter sunk screws. Custom made front panels can be installed with models 700-25 FB and 760-25 FB. b Remove the drawer from the casing. See "Removing the drawer". Panel dimensions The panel attached to the warming drawer front can be used as the drilling template for the custom panel.
Installation f Press the custom panel tight on to the removed panel. g Screw the removed panel to the custom panel with the eight screws. 28 h Hook the panels into the bottom on and secure at the top with two screws making sure the seal is seated correctly.
Alteration rights reserved / 3103 This paper has been bleached without chlorine. M.-Nr.
