Operating and Installation Instructions Freezer with Ice/Water Dispenser F 1471 Vi To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control panel for freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Control panel for Ice/Water Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Before use . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Water filter change indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Exchanging the water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Confirming the filter change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Using an external water filter . .
IMPORTANT SAFETY INSTRUCTIONS When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual. This appliance is for household use only. Use this appliance only for its intended use as described in this manual. Any other use could be dangerous.
IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the door closed until the appliance is completely installed and secured per installation instructions. ~ Before making plumbing connections, ensure the appliance is disconnected from the mains electricity supply. ~ Do not operate any appliance with a damaged cord or plug, or if the appliance has been damaged in any manner.
IMPORTANT SAFETY INSTRUCTIONS Use ~ This appliance is not designed for commercial use. It is intended for use in domestic households and in similar working and residential environments such as: ~ Avoid contact with the moving parts of the ejector mechanism, or with the heating element located on the bottom of the ice maker. Do not place fingers or hands on the automatic ice making mechanism while the appliance is plugged in.
IMPORTANT SAFETY INSTRUCTIONS ~ Do not block the ventilation gaps in the plinth or the top of the appliance housing unit, as this can impair the efficiency of the appliance, increase the electricity consumption and cause damage to the appliance. ~ Never use a steam cleaner to clean the appliance. Pressurized steam could damage electrical components and cause a short circuit. ~ Before using the Ice/Water dispenser it is important to flush the lines and clean the part thoroughly.
Guide to the freezer a Interior lighting b Door shelf c Ice cube maker d Ice cube container e Interior shelf f Control panel for the Freezer g Main switch to turn the appliance On/Off h Freezer baskets i Water filter j Ice / Water dispenser in the door k Control panel for Ice / Water Dispenser l Ice / Water dispenser outlet m Drip tray with grid and cover 8
Guide to the freezer Control panel for freezer a Access button "p" activates the control panel d On/Off sensor button for the Ice/Water dispenser b Temperature display X colder; Y warmer Allows you to set the desired temperature in the freezer e Sensor button for the temperature and/or door alarm* c On/Off sensor button for the SuperCool function f Water filter change indicator* * Only visible when the relevant function is activated Control panel for Ice/Water Dispenser a Lighting sensor button d C
Before use Before using for the first time Turning the appliance On/Off ^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap. Dry with a soft cloth. ^ Open the appliance door. If the appliance was transported or laid horizontally for any reason, allow it to stand vertical for at least 8 hours before turning it on. Failure to do so will affect the functioning of the appliance. ^ Turn the appliance On/Off with the main switch.
Settings Using the settings Additional settings This appliance is operated with the use of touch keys activated by a finger. In the settings mode you can select and change functions. – An available button will appear white. In settings mode, certain settings can be changed. The function possibilities are described in the respective chapters of this manual. – A selected button will appear yellow. Overview of the selectable function settings: ^ Touch the access button "p" so it turns yellow.
Settings Turning the button sound On/Off ^ Tap the X button until = appears in the display. If you prefer the buttons to be silent when touched the button sound can be turned off. ^ Touch the access button "p" to confirm. ^ Touch the access button "p" so it turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible.
Settings Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions need to be taken: ^ Shut off the water supply line, (several hours before switching off the appliance) ^ Take all food out of the appliance ^ Turn the appliance off ^ Unplug the appliance ^ Empty the ice cube container ^ Clean the interior ^ Remove and discard the water filter (secure the filter cap) ^ Leave the door open to prevent odors 13
Temperature and door alarm The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door. The alarm system is always operational, it does not need to be switched on. Temperature alarm If the temperature becomes too warm, an alarm sounds and the "alarm" indicator turns red and flashes and the temperature flashes in the control panel. The temperature display shows the highest temperature reached during the alarm.
Setting the temperature Setting the temperature Temperature range The temperature can be set within the following range: 7°F to -11°F (-14°C to -24°C). ^ Touch the access button "p" so it turns yellow. ^ Use the X and Y buttons next to the temperature display to set the temperature warmer or colder. Tap the X and Y sensor buttons to raise/lower the temperature 1°, or hold it down to move through the temperature range more quickly.
Setting the temperature Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ While holding down the X button, press the access button "p" once. Keep holding the X button down until the following appears in the display (approx. 5 seconds). ^ Touch the access button "p" so it turns yellow. ^ Tap the X button until † appears in the display. ^ Note the position of the X button, but do not touch. ^ Touch the access button "p" to confirm.
Using the freezer efficiently Freezing food Placing food in the freezer Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food. Food to be frozen can be placed anywhere in the freezer. Never refreeze partially or fully defrosted food. Consume defrosted food as soon as possible, it will lose its nutritional value and spoil if left for too long. Do not refreeze defrosted food unless it has been cooked.
Using the freezer efficiently Defrosting Cooling drinks quickly Frozen food can be defrosted in different ways: To cool drinks quickly, switch on the SuperCool function. See "SuperCool" for more information. – in a microwave oven, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep the other food cold), – in a steam oven. Poultry It is especially important to observe proper hygiene when defrosting poultry. Never save the liquid from defrosted poultry.
Using the freezer efficiently Freezing tips – The following are examples of foods suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, pastry/dough, leftovers, and a range of pre-cooked meals. – The following examples of foods not suitable for freezing: Lettuce, radishes, sour cream, mayonnaise, eggs in their shells, onions, whole raw apples and pears. – To retain color, taste and vitamin C, vegetables should be trimmed, washed, and blanched.
SuperCool When the SuperCool function is activated, the appliance is cooled as cold as possible (to a factory-preset temperature). SuperCool The SuperCool function is ideal for freezing large quantities of unfrozen food. Ideally the function should be switched on 4 - 6 hours before the food is placed in the freezer. If the max. freezing capacity is used, 24 hours are recommended. This helps food to freeze quickly and retain its nutrients, vitamins, flavor and appearance.
Ice/Water Dispenser Using the Ice/Water Dispenser for the first time Before using the Ice/Water Dispenser for the first time, you must flush then fill appliance water lines with water. Flushing the lines of the Ice/Water Dispenser ^ Open the freezer door. ^ Touch the "water" button until it flashes yellow. ^ Touch and hold the "water" button again. This activates the flushing function, which uses approximately 1.6 gallons (6 liters) of water. ^ Touch the "Access" button so it turns yellow.
Ice/Water Dispenser Turning on the Ice/Water Dispenser Before using the Ice/Water Dispenser for the first time, you must flush the water lines. ^ Open the freezer door. ^ Be sure the ice cube container is under the ice maker. Ice cubes can only be produced if the ice cube container is completely closed. ^ Turn on the Ice/Water dispenser with a finger touch to the control panel or by passing your hand under the dispenser to activate it via the light sensor.
Ice/Water Dispenser Dispensing water ^ Place a suitable cup on the drip tray under the ice/water dispenser. ^ Press and hold the "water" button. As long as you hold in the "water" button, water will flow from the dispenser. After a period of time the water flow will automatically stop. If more water is needed press the "water" button again. If you would like the water colder, place ice cubes in the glass before dispensing water.
Ice/Water Dispenser If the ice/water dispenser is not used for more than 2 minutes or the freezer door is opened, Standby mode is activated and the lighting for the ice/water dispenser will go out. When used again, it will take a few seconds for the water and ice to be dispensed. Safety lock The Ice/Water dispenser can be locked to prevent unwanted use. If the Ice/Water dispenser is not used for longer than 2 minutes, it switches into standby mode, and the Ice/Water dispenser lighting turns off.
Ice/Water Dispenser Settings Anti-condensation heater The following settings on the Ice/Water dispenser can be adjusted: A heater behind the control panel of the Ice/Water dispenser ensures that frost and ice do not build-up. To save energy, you can turn the heater off. Entering the settings mode This feature is turned off by factory default. To turn the anti-condensation heater on: ^ Touch and hold the "lock" button so that it appears white.
Ice/Water Dispenser Anti-clumping Button sound The anti-clumping feature ensures that crushed ice or ice cubes do not freeze together. A noise will be heard periodically to indicate that the feature is working. If the sound disturbs you, the feature can be turned off. If you prefer the buttons to be silent when touched, the button sound can be turned off. This feature is turned on by factory default. Note: Disabling the anti-clumping feature can result in the formation of ice clumps in the dispenser.
Automatic defrost The freezer defrosts automatically. The moisture generated in the appliance collects in the evaporator. It is automatically defrosted and dissipated by the condenser periodically. This automatic defrosting system enables the freezer to remain permanently ice-free, while ensuring that the food stored in the freezer stays frozen.
Adjusting the interior fittings Moving the shelves Door shelf The shelves can be adjusted according to the height of the food. For easier loading, unloading and cleaning the door shelf can be shifted or completely removed. ^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings. ^ Pull the shelf forward. ^ Move the shelf to the desired height, then insert the (rear) hooks into place. ^ Make sure the shelf is level.
Adjusting the interior fittings Freezer baskets Replacing the freezer basket For easier loading, unloading, and cleaning, the freezer baskets can be shifted or completely removed. ^ Fully extend the telescopic tracks. ^ Pull the basket forward until resistance is felt. On the hinged-side of the door is a safety lock, which must be turned to a horizontal position before the drawer can be removed. ^ Lay the basket onto the tracks so that it connects in the front and back.
Cleaning and care To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance.
Cleaning and care Before cleaning Cleaning the interior and accessories Use a mild solution of warm water and liquid dish soap. Wash all accessories and drawers by hand. Do not wash in a dishwasher. ^ Use the main switch to turn the appliance off completely. The main switch is located on the right side underneath the control panel. ^ Unplug the power cord. ^ Remove any food from the appliance and store it in a cool place. ^ Clean the appliance as needed.
Cleaning and care Aluminum frames Ice cube container The frames of the door bins and shelves are made of aluminum. ^ Pull out the ice cube container. ^ Clean with a mild solution of warm water and liquid dish soap. Aluminum is susceptible to scratches and nicks, treat with care. The aluminum frames may become discolored or otherwise altered if soiling is not cleaned away promptly.
Cleaning and care Ventilation slits After cleaning ^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed. ^ Return all shelves and accessories. Door seals Do not use any oils or grease on the door seals. This may cause the seals to deteriorate and become porous over time. ^ Clean the door seals with warm water and dry thoroughly. ^ Plug in the appliance and turn it on with the main switch. ^ Switch on the SuperCool function.
Cleaning and care Changing the light bulb The lighting automatically switches off after the door has been open for approx. 10 minutes. This is not a fault. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold with a soft cloth. If the light does not come on when the door is opened briefly, the light bulb should be changed. ^ Use the main switch to turn the appliance off.
Cleaning and care Side lighting Ice/Water Dispenser lighting Do not remove the light cover for the dispenser lighting. Should the lighting covers be damaged or need to be removed due to damage, do not look directly or with an optical instrument at the lighting. ^ Turn the light cover counterclockwise and pull out. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold with a soft cloth.
Water filter The appliance is supplied with an active charcoal filter which improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water. Additional water filters are available from Miele. It is important to change the water filter regularly. To avoid serious illness or death, do not use water that is microbiologically or chemically unsafe or of unknown quality without adequate disinfection or other treatment before or after use of a filter.
Water filter Exchanging the water filter Note: Air trapped in the system may cause water and the filter cartridge to eject forcefully. Use caution when removing. ^ Remove the cap from the used filter, 3. ^ Take a new filter cartridge out of the packaging and remove the protective cap. ^ Push the cap onto the new filter cartridge, 4. ^ Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180°, 1. ^ Pull the used filter cartridge out of the appliance, 2.
Water filter Using an external water filter ^ After the filter change the filter indicator in the display still flashes. The change must be be confirmed in the electronic. Confirming the filter change ^ Press and hold the filter change sensor button. ^ At the same time place a finger on the access button. Press and hold both sensor buttons for approx. 5 seconds until a beep is heard. The water filter change has been confirmed and the filter change indicator had been reset.
Water filter State of California Department of Public Health Water Treatment Device Certificate Number 06 - 1775 Date Issued: March 10, 2006 Date Revised: April 3, 2008 Trademark/Model Designation 9000 077095 Miele 07134220 Replacement Elements 9000 077104 07134220 Manufacturer: Cuno, Incorporated The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminants: Microbiologica
Water filter Performance Data Sheet For Filter Model 07134220 Using Replacement Cartridge 07134220 This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.
Lead free certificate This product F 1471 Vi (KIMIWD18US) is tested and certified by WQA against ORD0902 for California "lead free" compliance. Miele & Cie.
Frequently asked questions With the aid of the following guide minor problems can be corrected without a service call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty. Problems with temperature Issue Possible fault Solution The freezer does not get cold. The machine is not turned Check whether the appliance is on.
Frequently asked questions General problems Issue Possible fault Solution Water is flowing out of Close the shut-off valve immediately. the appliance. Check whether the water Contact Miele Technical pipe in the appliance is Service. defective. Check whether the water pressure is too low. Contact a plumber. Check whether the correct Self-tapping valves and water valve has been 3/16" (4.76 mm) saddle installed. valves reduce the water pressure and can block the pipe. The door will not open.
Frequently asked questions Alarm / Indicator warnings Issue Possible fault Solution The alarm is going off. The appliance door(s) have been open for longer than 5 minutes. Close the door. The alarm is ringing and The door is not closed. the "alarm" indicator is A large amount of fresh flashing. food is being frozen at the same time. There has been a power failure. Once the alarm condition has been corrected, the alarm will turn off and the "alarm" indicator will go out.
Frequently asked questions Problems with the ice/water dispenser Issue Possible fault Solution The ice maker is When the appliance is turned on for the very first time, it can not producing take up to 10 hours for the first ice cubes to drop out of the ice any ice. cube maker and collect in the container. The appliance is not turned on. Check that the appliance is switched on. The water supply line was not primed (purged of air) before the appliance was used for the first time. Contact Miele.
Frequently asked questions Problems with the ice/water dispenser Issue Possible fault Solution The ice cubes are small. Other domestic appliances that use water are in operation. Avoid using such items as a dishwasher, washing machine or shower at the same time. Check whether the water filter needs changing. See "Water filter" for more information. Check the water pressure. Consult a plumber. The water pressure must be between 25 and 80 psi (1.7-5.5 bar).
Frequently asked questions Problems with the ice/water dispenser Issue Possible fault Solution The ice maker is not producing enough ice or the ice cubes are misshapen. Check the water pressure. The water pressure must be between 25 and 80 psi (1.7-5.5 bar). Contact a plumber. Check that the freezer temperature is not too high. See "Selecting the correct temperature". Change the water filter. See "Water filter". The Ice/Water dispenser The appliance is not does not appear to be plugged in.
Frequently asked questions The appliance is making noises. Issue Possible fault Solution Brrrrr... Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on. Blubb, blubb... A gurgling noise can be heard when coolant is circulating through the pipes. These noises are not a fault. The noise of the compressor and the coolant circulating in the system is unavoidable. Click...
After sales service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
Installation Instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and machine damage read these instructions before installation or use.
Caring for the environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling center about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc., are disposed of safely and kept out of the reach of babies and young children.
Installation Installation site Have the appliance installed by a qualified technician, according to the enclosed installation instructions. WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. Keep the door closed until the appliance is completely installed and secured as per the installation instructions. Empty weight of your machine: F 1471 Vi . . . . . . . . . . 306 lbs (139 kg) The appliance should be installed in a dry, well ventilated room.
Installation Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after installation and that the appliance is installed in accordance with these installation instructions and and with the required ventilation openings.
Installation Base Ventilation A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements. The approx. weight of a fully loaded machine is: The air intake and outlet must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis. F 1471 Vi . . . . . . . . . . .
Installation Stainless steel panels Side-by-side Stainless steel door panels and toe-kick covers are available from Miele. This appliance can be installed "side-by-side" with another fridge/freezer using a "Merging Kit". Custom door panels The "Merging Kit" is available from Miele. This appliance is compatible with all styles and designs of kitchen cabinetry. The total weight of the decorative panel(s) must not exceed the following: F 1471 Vi . . . . . . . . . . .
Installation Installation with partition using the "Merging Kit" The minimum thickness of the partition is 5/8" (16 mm). Side panels If one side of the appliance is visible, a side panel must be used. The side panel must be firmly secured to the wall, the floor and the overhead furniture/fixtures before the appliance is placed in the cavity. The dimensions of the side panel are taken from the opposite wall of the installation space.
Installation Door dimensions (open 115°) The dimensions of the door fronts and handles will vary according to each individual kitchen. F 1471 Vi A B C D 20 11/16" (525 mm) Door front max. 1 1/2" (38 mm) Door handle 9 3/16" (234 mm) Miele recommends using the full door opening angle of 115° for this freezer.
Installation Niche dimensions Niche width (A) F 1471 Vi 18" (457 mm) 59
Installation Power supply and water connection 1. Power supply 2. Water connection A F 1471 Vi 9" (229 mm) Install a pressure limiting device and water hammer arrester for inlet water pressures exceeding 80 psi.(Refer to Uniform Plumbing Code, Sections 608.2 and 609.10) Never install or operate where inlet water pressure may exceed 120 psi.
Installing the appliance Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation. These installation instructions are intended for use by qualified installers.
Installing the appliance Aligning the housing unit Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity. ^ Check that the cavity is square. ^ Check the location of the power outlet. ^ Check the location of the water connection (see "Plumbing").
Installing the appliance ^ From the rear of the appliance carefully lift it from the pallet. Once the appliance is on the ground it can be wheeled around. ^ Do not remove the installation supports from the appliance door. They will be used later in the installation niche. There are transportation safety devices inside the appliance to protect the shelves and storage compartments until installation is complete. Do not remove them, or parts may be damaged. ^ Check the appliance for damage in transit.
Installing the appliance RemoteVision module installation (optional accessory) Always disconnect the appliance from the power supply when performing installation, maintenance or service work. Install the RemoteVision module before placing the appliance in its installation niche. Once connected the RemoteVision module will increase the energy consumption of the appliance. The slot for the RemoteVision module is located in the lower area of the back of your appliance.
Installing the appliance ^ Push the module into the slot until it locks into place. ^ Connect the appliance to the power supply and turn it on. After several seconds the indicator light e will come on. The indicator light will display different colors one after the other; any control light at the end indicates that the module was correctly installed. If the indicator light does not come on, installation of the module was unsuccessful. In that case, repeat the process.
Installing the appliance Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are marked alphabetically. The bag needed for each step will be marked with its respective letter. Anti-tip brackets The anti-tip brackets a keep the appliance safely secured in the installation niche b and prevent it from tipping. Two anti-tip brackets are recommended for each appliance.
Installing the appliance In a cabinet without a back wall ^ Now attach the installation niche to the wall. The built-in cabinet must be secured to the wall behind it with several screws. In a cabinet with a back wall ^ screw the cabinet to the wall behind it in several places using suitable mounting brackets. For this, use suitable plugs/screws depending on the type of wall. ^ screw the back wall of the cabinet in several places directly to the wall behind it.
Installing the appliance Securing an alternative anti-tip device If the anti-tip brackets cannot be attached securely using a wooden beam, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. If possible, always screw the wooden beam to existing studs. ^ Mark the installation height (lower edge of the beam) on the rear wall of the niche. ^ Select screws according to the thickness of the wooden beam.
Installing the appliance Sliding the appliance into the installation niche If a side-by-side installation is desired, connect the two appliances together. See the Installation Manual included with the "Merging Kit". ^ Plug the appliance into the power outlet a. The plug of the appliance should be easily accessible after installation. If the plug is not accessible after the appliance has been installed, disconnection from the power supply should be completed via the circuit breaker.
Installing the appliance Aligning the appliance ^ Align the appliance with the custom front. Important! When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. – Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4" (32 mm). The guide dimension of 1 1/4" (32 mm) is related to a niche height of 84" (2134 mm).
Installing the appliance Attaching the appliance to the installation niche ^ Secure the attachment plate side lugs. ^ Screw the attachment plate lugs f to the overhead furniture/fixtures. If there is no way to attach the top of the appliance, it can be attached to the sides of the installation niche. ^ If necessary, shorten the filler strip h to the required height. ^ Place the 2 strips on top of each other i. ^ Insert the filler strip until you hear it click into place j.
Installing the appliance For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip: ^ Open the appliance door. ^ Take the peg from the "side-by-side merging kit" and insert it halfway into the filler strip rail on the left-side appliance. ^ Place the second filler strip on the peg and press both filler strips together. ^ Click the filler strips into place above the appliance. ^ Screw the attachment plate lugs k to the adjacent furniture/fixtures.
Installing the appliance Preparing the custom door ^ Load the door basket. ^ Open the appliance door. ^ Unscrew the installation supports l from the appliance door. ^ Measure the distance X between the bracket from the door and the overhead furniture/fixtures. ^ Loosen the remaining screws from the strips m on each side of the door, then remove. ^ Loosen the two nuts. Set aside the nuts - you will need them again later. ^ Set aside the screws and side strips m - you will need them again later.
Installing the appliance The bracket includes a variety of holes for the various design options of custom doors. When performing work on the custom door, always observe the following: – Always select the best load-bearing surface of the custom door as the location for screws. – Always select a screw length that is shorter than the thickness of the door front. ^ Secure the door handle to the front of the appliance from the inside. ^ Mark the distance X on the back-side of the custom door.
Installing the appliance Attaching and aligning the custom door front ^ Align the custom door height with the threaded bolts n. ^ Now tighten the nuts o on top. This secures the appliance door. ^ Open the door and hang the custom door with the mounting frame over the threaded bolts n. ^ Put the side strips m back into place and screw them completely down on both sides of the appliance door. Bag E contains spare screws for this purpose. ^ Screw the nuts o a few turns onto the threaded bolts n.
Installing the appliance Attaching the covers ^ To mount the cover strips on both sides of the door, click them into place from bottom to top, into the gap between the appliance door and the custom door. ^ Insert the cover strip into the space between the appliance and the side panel. For side-by-side combinations, the cover strips (on both sides of the appliance) are applied to the outermost spaces only. ^ Attach the light switch cover.
Installing the appliance Attaching the toe-kick cover The maximum height of the toe-kick cover is 4" (102 mm) from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance. Mounting the air separator The air separator on the inside of the freezer door keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit.
Installing the appliance Aligning the Ice/Water Dispenser If necessary the depth of the Ice/Water dispenser can be aligned from inside the custom door cut-out. This allows the dispenser to be aligned with the custom door to achieve the best possible appearance. ,Disconnect the appliance from the power supply. ^ Remove the cover and the plastic grill. ^ Press the dispenser back and pull downwards to remove. ^ Remove the screw from the rear casing, then lift the tab on the drip tray up and off.
Installing the appliance Once the drip tray has been removed, the four metal strips can be used to align the Ice/Water Dispenser. ^ Pull the rear cover forward and out. ^ Loosen the screws of the four metal strips. ^ Insert a screwdriver into one of the four slots and push sideways until the dispenser is aligned with the custom door (the gray arrow will adjust to the rear; the black arrow will adjust front). ^ Re-tighten the screws of the strips.
Installing the appliance Attaching the frame and the shelf The word "TOP" is marked on the rear of the frame at the top. For 3/4" (19 mm) thick custom doors: ^ Slide the cover frame onto the Ice/Water Dispenser and press until it is flush with the door front. For 1 1/2" / (38 mm) thick custom doors: ^ Fit the extension trim onto frame. ^ Fit the cover frame onto the Ice/Water Dispenser and press it firmly into position until it is flush with the door surface.
Plumbing All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations. Disconnect the appliance from the electrical power supply before connecting it to the water supply. Turn off the water supply before connecting the water lines to the ice cube maker. The shut-off valve for the water connection must not be located behind the appliance.
Plumbing Preparing the water connection For appliances with a hose guide The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Install the connecting pipe.
Plumbing Connecting the water supply ^ Push the union nut and seal onto the water pipe. When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Push the end of the water pipe into the appliance connection and screw on the union nut, 3. First tighten by hand. When bending the water pipe, be sure not to kink it, otherwise there is a risk of leaks and water damage. Use bending aids.
Electrical connection , Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
RemoteVision (optional accessory) Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem. For information on set-up and installation of the RemoteVision module see the "Installation" section of this manual.
RemoteVision (optional accessory) Accessing the RemoteVision control panel ^ Tap the X button until ; appears in the display. ^ Touch the access button "p" to confirm. ^ Touch the access button "p" so it turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible. ^ Place one finger on the position of the X button and hold (the X button will not be visible).
RemoteVision (optional accessory) MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network established, no IP address assigned Solid ;# Connected to network Flashing ; < In Ad-Hoc Mode, not connected Flashing ; = In Ad-Hoc Mode, connected Selectable options Description of function ;- Back ;2 Reboot the module ;3 Reset to factory settings ;4 Enter
Alteration rights reserved / 0414 M.-Nr. 09 743 700 / 01 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.