Operating and Installation Instructions Freezer with Ice Maker F 1801 Vi, F 1811 Vi F 1901 Vi, F 1911 Vi To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Turning the appliance On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Settings . . . . . . . . . . . . . . . . . . . . . .
Contents Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Stainless steel panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Custom door panels . . .
IMPORTANT SAFETY INSTRUCTIONS When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual. Only use the appliance for its intended purpose. This appliance complies with current safety requirements. Improper use of the appliance can lead to personal injury and material damage.
IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the door closed until the appliance is completely installed and secured per installation instructions. ~ This appliance must be installed and connected in compliance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician.
IMPORTANT SAFETY INSTRUCTIONS ~ Persons who lack physical, sensory or mental abilities, or experience with the machine should not use it without supervision or instruction by a responsible person. ~ To reduce the risk of injury, do not allow children to play in, on or near the appliance, especially in the door hinge area. ~ After your freezer is in operation, do not touch the cold surfaces in the freezer compartment, particularly when hands are damp or wet. Skin may adhere to these extremely cold surfaces.
IMPORTANT SAFETY INSTRUCTIONS Disposal of your old appliance ~ Before disposing of an old appliance, first make the door latch or lock unusable. ~ Take off the door. ~ Leave the shelves in place so that children may not easily climb inside. ~ Consult with your municipal policy on recycling. ~ Be careful not to damage any part of the pipework while awaiting disposal by: puncturing the refrigerant channels in the evaporator. bending any pipework. scratching the surface coating.
Guide to the freezer a Door shelves (height adjustable) b Shelves (height adjustable) c Ice cube maker d Ice cube container e Control panel f Main switch to turn the appliance On/Off g Freezer baskets h Water filter 8
Guide to the freezer Control panel a Access button "p" b Temperature display X colder; Y warmer Allows you to set the desired temperature in the freezer c On/Off sensor button for the SuperCool function d On/Off sensor button for the ice cube maker e Sensor button for the temperature and door alarm* f Water filter change indicator* * Only visible when the relevant function is activated 9
Before use Before using for the first time Turning the appliance On/Off ^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap. Dry with a soft cloth. ^ Open the appliance door. If the appliance was transported to the installation site horizontally, leave the appliance standing upright for approx. 8 hours before connecting it to the electrical supply. This is very important to ensure correct functioning.
Settings Using the settings Additional settings This appliance is operated with the use of touch keys activated by a finger. In the settings mode you can select and change functions. – An available button will appear white. In settings mode, certain settings can be changed. The function possibilities are described in the respective chapters of this manual. – A selected button will appear yellow. Overview of the selectable function settings: ^ Touch the access button "p" so it turns yellow.
Settings Turning the button sound On/Off If you prefer the buttons to be silent when touched the button sound can be turned off. ^ Touch the access button "p" so it turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible. ^ Place one finger on the position of the X button and hold (the X button will not be visible). ^ While holding down the X button, press the access button "p" once.
Settings Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions need to be taken: ^ Shut off the water supply line, (several hours before switching off the appliance) ^ Take all food out of the appliance ^ Turn the appliance off ^ Unplug the appliance ^ Empty the ice cube container ^ Clean the interior ^ Remove and discard the water filter (secure the filter cap) ^ Leave the door open to prevent odors 13
Temperature and door alarm The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door. The alarm system is always operational, it does not need to be switched on. Temperature alarm If the temperature becomes too warm, an alarm sounds and the "alarm" indicator turns red and flashes and the temperature flashes in the control panel. The temperature display shows the highest temperature reached during the alarm.
Setting the temperature Setting the temperature Temperature range The temperature can be set within the following range: 7°F to -11°F (-14°C to -24°C). ^ Touch the access button "p" so it turns yellow. ^ Use the X and Y buttons next to the temperature display to set the temperature warmer or colder. Tap the X and Y sensor buttons to raise/lower the temperature 1°, or hold it down to move through the temperature range more quickly.
Setting the temperature Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ While holding down the X button, press the access button "p" once. Keep holding the X button down until the following appears in the display (approx. 5 seconds). ^ Touch the access button "p" so it turns yellow. ^ Tap the X button until † appears in the display. ^ Note the position of the X button, but do not touch. ^ Touch the access button "p" to confirm.
Using the freezer efficiently Freezing food Placing food in the freezer Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food. Food to be frozen can be placed anywhere in the freezer. Never refreeze partially or fully defrosted food. Consume defrosted food as soon as possible, it will lose its nutritional value and spoil if left for too long. Do not refreeze defrosted food unless it has been cooked.
Using the freezer efficiently Defrosting Cooling drinks quickly Frozen food can be defrosted in different ways: To cool drinks quickly, switch on the SuperCool function, see "SuperCool" for more information. – in a microwave oven, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep the other food cold), – in a steam oven. Poultry It is especially important to observe proper hygiene when defrosting poultry. Never save the liquid from defrosted poultry.
Using the freezer efficiently Freezing tips – The following are examples of foods suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, pastry/dough, leftovers, and a range of pre-cooked meals. – The following examples of foods not suitable for freezing: Lettuce, radishes, sour cream, mayonnaise, eggs in their shells, onions, whole raw apples and pears. – To retain color, taste and vitamin C, vegetables should be trimmed, washed, and blanched.
SuperCool When the SuperCool function is activated, the appliance is cooled as cold as possible (to a factory-preset temperature). SuperCool The SuperCool function is ideal for freezing large quantities of unfrozen food. Ideally the function should be switched on 4 - 6 hours before the food is placed in the freezer. If the max. freezing capacity is used, 24 hours are recommended. This helps food to freeze quickly and retain its nutrients, vitamins, flavor and appearance.
Ice cube maker For the automatic ice cube maker to operate, it must be connected to the household water supply. See "Plumbing". Turning on the ice cube maker ^ Make sure that the ice cube container is under the ice cube maker, as far as possible. Ice cubes will not be produced unless the container is completely closed. ^ Touch the sensor button for the ice cube maker so that it turns yellow. As soon as the freezer has cooled to a freezing temperature, the ice cube container fills with water.
Automatic defrost The freezer defrosts automatically. The moisture generated in the appliance collects in the evaporator. It is automatically defrosted and dissipated by the condenser periodically. This automatic defrosting system enables the freezer to remain permanently ice-free, while ensuring that the food stored in the freezer stays frozen.
Adjusting the interior fittings Moving the shelves Replacing a door shelf The shelves can be adjusted according to the height of the food. ^ Start at the top of the slide-rails and slide the shelf down into the desired position. ^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings. ^ Pull the shelf forward. ^ Move the shelf to the desired height, then insert the (rear) hooks into place. ^ Make sure the shelf is level.
Adjusting the interior fittings Ice cube container The ice cube container is set on telescopic tracks, and can be removed for loading, unloading and cleaning. ^ Slide the container forward until resistance is felt. ^ On both sides of the container, pull the latches (see arrow) upward and lift the container out of the freezer. Push the tracks back into the freezer to avoid injury. Replacing the ice cube container ^ Completely extend the telescopic tracks.
Cleaning and care To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance.
Cleaning and care Before cleaning Aluminum frames The shelf frames and the door baskets are made of aluminum. ^ Clean the frames with a mild solution of warm water and liquid dish soap. ^ Use the main switch to turn the appliance off completely. The main switch is located on the right side underneath the control panel. ^ Unplug the power cord. ^ Remove any food from the appliance and store it in a cool place. ^ Take out any removable parts, e.g., shelves.
Cleaning and care Ventilation slits After cleaning ^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed. ^ Return all shelves and accessories. Door seals ^ Turn on the SuperCool function. The freezer section will cool down quickly. Do not use any oils or grease on the door seals. This may cause the seals to deteriorate and become porous over time. ^ Clean the door seals with warm water and dry with a soft cloth.
Cleaning and care Changing the light bulb The lighting automatically switches off after the door has been open for approx. 5 minutes. This is not a fault. After the bulb has cooled for a short time it will turn on again. If the light does not come on when the door is opened briefly, the light bulb should be changed. ^ Use the main switch to turn the appliance off. To reduce the risk of electric shock, disconnect the appliance from the power supply by unplugging or tripping the circuit breaker.
Cleaning and care Side lighting ^ Turn the light cover counterclockwise and pull out. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold with a soft cloth. ^ Pull the defective light bulb from the socket. ^ Place the new bulb in the socket. Halogen bulb type: 5 W/12 V/socket G 4. ^ Put the light cover back on and turn clockwise into place. ^ Restore power to the appliance.
Water filter The appliance is supplied with an active charcoal filter which improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water. Additional water filters are available from Miele. It is important to change the water filter regularly. To avoid serious illness or death, do not use water that is microbiologically or chemically unsafe or of unknown quality without adequate disinfection or other treatment before or after use of a filter.
Water filter Exchanging the water filter Note: Air trapped in the system may cause water and the filter cartridge to eject forcefully. Use caution when removing. ^ Remove the cap from the used filter, 3. ^ Take a new filter cartridge out of the packaging and remove the protective cap. ^ Push the cap onto the new filter cartridge, 4. ^ Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180°, 1. ^ Pull the used filter cartridge out of the appliance, 2.
Water filter Using an external water filter ^ After the filter change the filter indicator in the display still flashes. The change must be be confirmed in the electronic. Confirming the filter change ^ Press and hold the filter change sensor button. ^ At the same time place a finger on the access button. Press and hold both sensor buttons for approx. 5 seconds until a beep is heard. The water filter change has been confirmed and the filter change indicator had been reset.
Water filter State of California Department of Public Health Water Treatment Device Certificate Number 06 - 1775 Date Issued: March 10, 2006 Date Revised: April 3, 2008 Trademark/Model Designation 9000 077095 Miele 07134220 Replacement Elements 9000 077104 07134220 Manufacturer: Cuno, Incorporated The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminants: Microbiologica
Water filter Performance Data Sheet For Filter Model 07134220 Using Replacement Cartridge 07134220 This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.
Lead free certificate This product F 1801 Vi, F 1811 Vi (KIMSDF30US) / F 1901 Vi, F 1911 Vi (KIMSDF36US) is tested and certified by WQA against ORD0902 for California "lead free" compliance. Miele & Cie.
Frequently asked questions With the aid of the following guide minor problems can be corrected without a service call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty. Problems with temperature Issue Possible fault Solution The freezer does not get cold. The machine is not turned on.
Frequently asked questions General problems Issue Possible fault Solution Water is flowing out of Close the shut-off valve immediately. the appliance. Check whether the water Contact Miele Technical pipe in the appliance is Service. defective. Check whether the water pressure is too low. Contact a plumber. Check whether the correct Self-tapping valves and water valve has been 3/16" (4.76 mm) saddle installed. valves reduce the water pressure and can block the pipe. The door to the This is not a fault.
Frequently asked questions Alarm / Indicator warnings Issue Possible fault Solution The alarm is going off. The appliance door(s) have been open for longer than 5 minutes. Close the door. The alarm is ringing and The door is not closed. the "alarm" indicator is A large amount of food is flashing. being frozen at the same time. Once the alarm condition has been corrected, the alarm will turn off and the "alarm" indicator will stop flashing. There has been a power failure. The filter display is red.
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice cube maker will not switch on. The appliance is not plugged in. Check that the appliance is connected to the power supply. The ice cube maker is When the appliance is turned on for the very first time, it not producing any ice can take up to 10 hours for the first ice cubes to drop cubes. out of the ice cube maker and collect in the container. The appliance is not turned Check that the appliance is on.
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice cubes are small. Other domestic appliances that use water are in operation. Avoid using such items as a dishwasher, washing machine or shower at the same time. Check whether the water filter needs changing. See "Water filter" for more information. Check the water pressure. Consult a plumber. The water pressure must be between 25 and 80 psi (1.7-5.5 bar).
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice maker is not producing enough ice or the ice cubes are misshapen. Check the water pressure. The water pressure must be between 25 and 80 psi (1.7-5.5 bar). Contact a plumber. Check that the freezer temperature is too high. See "Selecting the correct temperature". Change the water filter. See "Water filter". Check the water pressure. The water pressure must be between 25 and 80 psi (1.7-5.5 bar).
Frequently asked questions The appliance is making noises. Issue Possible fault Solution Brrrrr... Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on. Blubb, blubb... A gurgling noise can be heard when coolant is circulating through the pipes. These noises are not a fault. The noise of the compressor and the coolant circulating in the system is unavoidable. Click...
After sales service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
Installation Instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and machine damage read these instructions before installation or use.
Caring for the environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling center about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc., are disposed of safely and kept out of the reach of babies and young children.
Installation Installation site Have the appliance installed by a qualified technician, according to the enclosed installation instructions. WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. Keep the door closed until the appliance is completely installed and secured as per the installation instructions. Empty weight of your machine: F 18X1 Vi . . . . . . . . . . 421 lbs (191 kg) F 19X1 Vi . . . . . . . . . .
Installation Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after installation and that the appliance is installed in accordance with these installation instructions and and with the required ventilation openings.
Installation Base Ventilation A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements. The approx. weight of a fully loaded machine is: The air intake and outlet must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis. F 18X1 Vi . . . . . . . . . . 950 lbs (430 kg) F 19X1 Vi . . . . . . . . .
Installation Stainless steel panels Side-by-side Stainless steel door panels and toe-kick covers are available from Miele. This appliance can be installed "side-by-side" with another fridge/freezer using a "Merging Kit". Custom door panels The "Merging Kit" is available from Miele. This appliance is compatible with all styles and designs of kitchen cabinetry. The total weight of the decorative panel(s) must not exceed the following: F 18X1 Vi . . . . . . . . . . . 106 lbs (48 kg) F 19X1 Vi . . . . . .
Installation Installation with partition using the "Merging Kit" The minimum thickness of the partition is 5/8" (16 mm). Side panels If one side of the appliance is visible, a side panel must be used. The side panel must be firmly secured to the wall, the floor and the overhead furniture/fixtures before the appliance is placed in the cavity. The dimensions of the side panel are taken from the opposite wall of the installation space.
Installation Front panel gap kit (optional accessory) Two adjacent doors can be attached instead of one large door. To connect these doors on the rear, a metal strip can be purchased as an optional accessory. Contact Miele. When attaching the metal strip to the furniture doors, observe the maximum length of the screws and the position of the drill holes. Always screw into the best possible load-bearing material of the custom doors.
Dimensions Door dimensions (open 115°) A B C D F 18X1 Vi 32 5/8" (829 mm) Door front max. 1 1/2" (38 mm) Door handle* 14 5/16" (363 mm) F 19X1 Vi 38 11/16" (982 mm) Door front max. 1 1/2" (38 mm) Door handle* 16 7/8" (428 mm) *The dimensions of the door fronts and handles will vary according to each individual kitchen. Miele recommends using the full door opening angle of 115° for this freezer.
Dimensions Niche dimensions Niche width (A) F 18X1 Vi 30" (762 mm) F 19X1 Vi 36" (915 mm) 54
Dimensions Power supply and water connection 1. Power supply 2. Water connection A F 18X1 Vi 15" (381 mm) F 19X1 Vi 18" (458 mm) Install a pressure limiting device and water hammer arrester for inlet water pressures exceeding 80 psi.(Refer to Uniform Plumbing Code, Sections 608.2 and 609.10) Never install or operate where inlet water pressure may exceed 120 psi.
Dimensions Door front dimensions A 1 B 3 F 18X1 Vi 79 /8" 2029 mm 29 /4" 756 mm F 19X1 Vi 79 1/8" 2029 mm 35 3/4" 908 mm 4" - 5 3/16" (102 - 132 mm) 56
Installing the appliance Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation. These installation instructions are intended for use by qualified installers. In addition to these instructions, the appliance must be installed in accordance with all local codes.
Installing the appliance Aligning the housing unit Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity. ^ Check that the cavity is square. ^ Check the location of the power outlet. ^ Check the location of the water connection (see "Plumbing").
Installing the appliance ,Caution! The appliance is no longer secured and may be unstable. ^ From the rear of the appliance carefully lift it from the pallet. ^ Do not remove the installation supports from the appliance door. They will be used later in the installation niche. There are transportation safety devices inside the appliance to protect the shelves and storage compartments until installation is complete. Do not remove them, or parts may be damaged. ^ Check the appliance for damage in transit.
Installing the appliance ^ Remove the cover b. ^ Push the module into the slot until it locks into place. ^ Connect the appliance to the power supply and turn it on. After several seconds the indicator light e will come on. The indicator light will display different colors one after the other; any control light at the end indicates that the module was correctly installed. If the indicator light does not come on, installation of the module was unsuccessful. In that case, repeat the process.
Installing the appliance Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are marked alphabetically. The bag needed for each step will be marked with its respective letter. Anti-tip brackets The anti-tip brackets a keep the appliance safely secured in the installation niche b and prevent it from tipping. Two anti-tip brackets are recommended for each appliance.
Installing the appliance In a cabinet without a back wall ^ Now attach the installation niche to the wall. The built-in cabinet must be secured to the wall behind it with several screws. In a cabinet with a back wall ^ screw the cabinet to the wall behind it in several places using suitable mounting brackets. For this, use suitable plugs/screws depending on the type of wall. ^ screw the back wall of the cabinet in several places directly to the wall behind it.
Installing the appliance Securing an alternative anti-tip device – The beam must cover the appliance by at least 2" (50.8 mm). If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. ^ Mark the installation height (lower edge of the beam) on the rear wall of the niche. If possible, always screw the wooden beam to existing studs.
Installing the appliance Sliding the appliance into the installation niche If a side-by-side installation is desired, connect the two appliances together. See the Installation Manual included with the "Merging Kit". ^ Plug the appliance into the power outlet a. The plug of the appliance should be easily accessible after installation. If the plug is not accessible after the appliance has been installed, disconnection from the power supply should be completed via the circuit breaker.
Installing the appliance Aligning the appliance ^ Align the appliance with the custom front. Important! When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. – Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4" (32 mm). The guide dimension of 1 1/4" (32 mm) is related to a niche height of 84" (2134 mm).
Installing the appliance Attaching the appliance to the installation niche ^ Secure the attachment plate side lugs. ^ Screw the attachment plate lugs f to the overhead furniture/fixtures. If there is a fairly large gap above the appliance, cut a wooden beam to fit exactly and place it in the gap. If there is no way to attach the top of the appliance, it can be attached to the sides of the installation niche. ^ If necessary, shorten the filler strip h to the required height.
Installing the appliance For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip: ^ Open the appliance door. ^ Take the peg from the "Side-by-side Merging Kit" and insert it halfway into the filler strip rail on the left-side appliance. ^ Place the second filler strip on the peg and press both filler strips together. ^ Screw the attachment plate lugs k to the adjacent furniture/fixtures.
Installing the appliance Preparing the custom door ^ Open the appliance door. ^ Unscrew the installation supports l from the appliance door. ^ Loosen the remaining screws from the strips m on each side of the door, then remove. ^ Set aside the screws and side strips m - you will need them again later. ^ Remove the light switch cover (see arrow). ^ Close the appliance door. 68 ^ Measure the distance X between the bracket from the door and the overhead furniture/fixtures. ^ Loosen the two nuts.
Installing the appliance ^ Mark the distance X on the back-side of the custom door. ^ Also calculate and mark the center of the custom door Y. ^ Remove the mounting frame from the appliance door and position it according to the markings on the custom door. ^ Pre-drill the holes. ^ Tightly screw on the bracket using the pre-drilled holes: Attach the bracket to each attachment point with at least one screw. ^ Attach the bracket at the top with at least 10 screws.
Installing the appliance Attaching and aligning the custom door front ^ Align the custom door height with the threaded bolts n. ^ Now tighten the nuts o on top. This secures the appliance door. ^ Open the door and hang the custom door with the mounting frame over the threaded bolts n. ^ Put the side strips o back into place and screw them completely down on both sides of the appliance door. Bag E contains spare screws for this purpose. ^ Screw the nuts o a few turns onto the threaded bolts n.
Installing the appliance Attaching the fixing brackets Attaching the covers (Only for appliances using the "Front panel gap kit".) The fixing brackets are used to secure the custom door front to the bottom of the appliance door. ^ To mount the cover strips on both sides of the door, click them into place from bottom to top, into the gap between the appliance door and the custom door. ^ Open the appliance door all the way. ^ Slightly loosen the screw (1.).
Installing the appliance Attaching the toe-kick cover The maximum height of the toe-kick cover is 4" from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance. ^ If required, cut the toe-kick cover to the required length and height. ^ Insert the cover strip into the space between the appliance and the side panel. For side-by-side combinations, the cover strips (on both sides of the appliance) are applied to the outermost spaces only.
Installing the appliance Mounting the air separator The air separator keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ Position the air separator in the center of the appliance door. ^ From below, screw the air separator firmly onto the door with the 2 screws. ^ If necessary, shorten the three parts of the air separator. ^ Insert the foam pieces back into the sides.
Plumbing All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations. Disconnect the appliance from the electrical power supply before connecting it to the water supply. Turn off the water supply before connecting the water lines to the ice cube maker. The water quality must conform to country requirements for drinking water. – The appliance is only suitable for connection to the cold water supply.
Plumbing Preparing the water connection For appliances with a hose guide The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Install the connecting pipe.
Plumbing Connecting the water supply ^ Push the union nut and seal onto the water pipe. When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Push the end of the water pipe into the appliance connection and screw on the union nut, 3. First tighten by hand. When bending the water pipe, be sure not to kink it, otherwise there is a risk of leaks and water damage. Use bending aids.
Electrical connection , Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
RemoteVision (optional accessory) Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem. For information on set-up and installation of the RemoteVision module see the "Installation" section of this manual.
RemoteVision (optional accessory) Accessing the RemoteVision control panel ^ Tap the X button until ; appears in the display. ^ Touch the access button "p" to confirm. ^ Touch the access button "p" so it turns yellow. See the table on the following page for a description of each setting in the display. ^ Note the position of the X button, but do not touch. ^ Use the Y or X buttons to select the RemoteVision options. ^ Touch the access button "p" again so it turns white.
RemoteVision (optional accessory) MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network established, no IP address assigned Solid ;# Connected to network Flashing ; < In Ad-Hoc Mode, not connected Flashing ; = In Ad-Hoc Mode, connected Selectable options Description of function ;- Back ;2 Reboot the module ;3 Reset to factory settings ;4 Enter
Alteration rights reserved / 3213 M.-Nr. 09 743 750 / 01 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
