Operating and Installation Instructions Freezer F 1411 SF To prevent accidents and machine damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Turning the appliance On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Settings . . . . . . . . . . . . . . . . . . . . .
Contents Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Installation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual. Only use the appliance for its intended purpose. The manufacturer cannot be held responsible for damages caused by improper use of this appliance. This appliance complies with current safety requirements.
IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the door closed until the appliance is completely installed and secured per installation instructions. ~ This appliance must be installed and connected in compliance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician.
IMPORTANT SAFETY INSTRUCTIONS ~ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. ~ Do not deactivate the water filter display. ~ Do not use sharp-edged objects to remove frost and ice, or separate frozen foods and remove ice trays. They will damage the evaporator, causing irreversible damage to the appliance.
Guide to the freezer a Door shelves (height adjustable) b Shelves (height adjustable) c Ice cube maker d Ice cube container e Control panel f Main switch to turn the appliance On/Off g Freezer basket h Water filter 7
Guide to the freezer Control panel a Access button "p" activates the control panel d On/Off sensor button for the ice cube maker b Temperature display X colder; Y warmer Allows you to set the desired temperature in the freezer e Sensor button for the temperature and door alarm* c On/Off sensor button for the SuperCool function 8 f Water filter change indicator* * Only visible when the relevant function is activated
Before use Before using for the first time Turning the appliance On/Off The stainless steel surface of the appliance is protected with a plastic film, which protects it during shipping. ^ Open the appliance door. Do not remove this protective film until the appliance has been completely installed. After removing the protective film clean the exterior surface with the supplied stainless steel agent. This will aid in preventing resoiling.
Settings Using the settings Custom settings When a sensor button has been selected with a finger touch, it will appear yellow. A de-selected button will appear white. In the custom settings mode you can select and change functions. The function possibilities are described in the respective chapters of this manual. Function ^ Touch the access button "p" so it turns yellow. On the control panel you will see additional sensor buttons to operate the appliance.
Settings Turning the button sound On/Off If you prefer the buttons to be silent when touched the button sound can be turned off. ^ Touch the access button "p" so it turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible. ^ Place one finger on the position of the X button and hold (the X button will not be visible). ^ While holding down the X button, press the access button "p" once.
Settings Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions need to be taken: ^ Shut off the water supply line, (several hours before switching off the appliance) ^ Take all food out of the appliance ^ Turn the appliance off ^ Unplug the appliance ^ Empty the ice cube container ^ Clean the interior ^ Remove and discard the water filter (secure the filter cap) ^ Leave the door open to prevent odors 12
Alarm The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door. The alarm system is always operational, it does not need to be switched on. Temperature alarm If the temperature becomes too warm, an alarm sounds and the "alarm" indicator turns red and flashes. The temperature display shows the highest temperature reached during the alarm.
Setting the temperature Setting the temperature Temperature range The temperature can be set within the following range: 7°F to -9°F (-14°C to -23°C). ^ Touch the access button "p" so it turns yellow. ^ Use the X and Y buttons next to the temperature display to set the temperature warmer or colder. Tap the X and Y sensor buttons to raise/lower the temperature 1°, or hold it down to move through the temperature range more quickly.
Setting the temperature Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ Touch the access button "p" so it turns yellow. ^ Note the position of the button X, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible. ^ Place one finger on the position of the X button and hold (the X button will not be visible). ^ While holding down the X button, press the access button "p" once.
Using the freezer efficiently Freezing food Placing food in the freezer Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food. Food to be frozen can be placed anywhere in the freezer. Never refreeze partially or fully defrosted food. Consume defrosted food as soon as possible, it will lose its nutritional value and spoil if left for too long. Do not refreeze defrosted food unless it has been cooked.
Using the freezer efficiently Defrosting Cooling drinks quickly Frozen food can be defrosted in different ways: To cool drinks quickly, switch on the SuperCool function. See "SuperCool" for more information. – in a microwave oven, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep the other food cold), Do not leave bottles in the freezer for more than 1 hour, closed containers could burst. – in a steam oven.
Using the freezer efficiently Freezing tips – The following are examples of foods suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, pastry/dough, leftovers, and a range of pre-cooked meals. – The following examples of foods not suitable for freezing: Lettuce, radishes, sour cream, mayonnaise, eggs in their shells, onions, whole raw apples and pears. – To retain color, taste and vitamin C, vegetables should be trimmed, washed, and blanched.
SuperCool When the SuperCool function is activated, the appliance is cooled as cold as possible (to a factory-preset temperature). SuperCool The SuperCool function is ideal for freezing large quantities of unfrozen food. Ideally the function should be switched on 4 - 6 hours before the food is placed in the freezer. If the max. freezing capacity is used, 24 hours are recommended. This helps food to freeze quickly and retain its nutrients, vitamins, flavor and appearance.
Ice cube maker For the automatic ice cube maker to operate, it must be connected to the household water supply. See "Plumbing". Turning on the ice cube maker Make sure that the ice cube container is under the ice cube maker, as far as possible. Ice cubes will not be produced unless the container is completely closed. ^ Touch the sensor button for the ice cube maker so that it turns yellow. As soon as the freezer has cooled to a freezing temperature, the ice cube tray fills with water.
Automatic defrost The freezer defrosts automatically. The moisture generated in the appliance collects in the evaporator. It is automatically defrosted and dissipated by the condenser periodically. This automatic defrosting system enables the freezer to remain permanently ice-free, while ensuring that the food stored in the freezer stays frozen.
Adjusting the interior fittings Moving the shelves Freezer baskets The shelves can be adjusted according to the height of the food. For easier loading, unloading, and cleaning, the freezer baskets can be shifted or completely removed. ^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings. ^ Pull the shelf forward. ^ Move the shelf to the desired height, then insert the (rear) hooks into place.
Adjusting the interior fittings Ice cube container The ice cube container is set on telescopic tracks, and can be removed for loading, unloading and cleaning. ^ Slide the container forward until resistance is felt. ^ On both sides of the container, pull the latches (see arrow) upward and lift the container out of the freezer. Push the tracks back into the freezer to avoid injury. Replacing the ice cube container ^ Completely extend the telescopic tracks.
Cleaning and care Before cleaning To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance. Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents. Non-abrasive cleaning agents are also unsuitable, as they can cause matte areas to appear.
Cleaning and care Appliance door Ventilation slits ^ Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. ^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed. ^ To help prevent resoiling, a conditioner for stainless steel can also be used. Apply sparingly with even pressure. Aluminum frames The shelf frames are made of aluminum.
Cleaning and care Changing the light bulb The lighting automatically switches off after the door has been open for approx. 5 minutes. This is not a fault. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold with a soft cloth. After the bulb has cooled for a short time it will turn on again. If the light does not come on when the door is opened briefly, the light bulb should be changed. ^ Use the main switch to turn the appliance off.
Cleaning and care Side lighting ^ Turn the light cover counterclockwise and pull out. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold with a soft cloth. ^ Pull the defective light bulb from the socket. ^ Place the new bulb in the socket. Halogen bulb type: 5 W/12 V/socket G 4. ^ Put the light cover back on and turn clockwise into place. ^ Restore power to the appliance.
Water filter The water filter improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water. – Depending on how many ice cubes are produced, the filter will need to be changed approximately every 6 months. It is important to change the water filter regularly.
Water filter Exchanging the water filter ^ Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180°, 1. ^ Pull the used filter cartridge out of the appliance, 2. ^ Push the filter cartridge with cap, in a horizontal position, all the way into the opening in the base panel, 5. ^ Rotate the filter cartridge clockwise 180° until the cap is in a horizontal position, 6. The filter change needs to be confirmed before the "filter" indicator will go out.
Water filter Re-setting the filter indicator The filter indicator still flashes in the display. ^ Touch the access button "p" so it turns yellow. ^ Note the position of the button X, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible. ^ Place one finger on the position of the X button and hold (the X button will not be visible). ^ While holding down the X button, press the access button "p" once.
Water filter ^ Tap the X button until ^ - appears in the display. ^ Touch the access button "p". ^ Tap the X button until ; appears in the display. ^ Touch the access button "p". You have left the Custom settings mode. The "filter" indicator is no longer visible on the control panel. Deactivating the water filter The ice cube maker in this appliance can be operated without the installed water filter, for example if the household water supply already uses a water filter.
Filter Performance Data Sheet State of California Department of Public Health Water Treatment Device Certificate Number 06 - 1775 Date Issued: March 10, 2006 Date Revised: April 3, 2008 Trademark/Model Designation 9000 077095 Miele 07134220 Replacement Elements 9000 077104 07134220 Manufacturer: Cuno, Incorporated The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminant
Filter Performance Data Sheet Performance Data Sheet For Filter Model 07134220 Using Replacement Cartridge 07134220 This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.
Frequently asked questions With the aid of the following guide minor problems can be corrected without a service call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty. Problems with temperature Issue Possible fault The freezer does not get cold. The machine is not turned Check whether the appliance is on.
Frequently asked questions General problems Issue Possible fault Solution Water is flowing out of Close the shut-off valve immediately. the appliance. Check whether the water Contact Miele Technical pipe in the appliance is Service. defective. Check whether the water pressure is too low. Contact a plumber. Check whether the correct Self-tapping valves and water valve has been 3/16" (4.76 mm) saddle installed. valves reduce the water pressure and can block the pipe. The door to the This is not a fault.
Frequently asked questions Alarm / Indicator warnings Issue Possible fault Solution The alarm is going off. The appliance door(s) have been open for longer than 5 minutes. Close the door. The alarm is ringing and The door is not closed. the "alarm" indicator is A large amount of food is flashing. being frozen at the same time. Once the alarm condition has been corrected, the alarm will turn off and the "alarm" indicator will stop flashing. There has been a power failure. The filter display is red.
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice cube maker will not switch on. The appliance is not plugged in. Check that the appliance is connected to the power supply. The ice cube maker is When the appliance is turned on for the very first time, it not producing any ice can take up to 10 hours for the first ice cubes to drop cubes. out of the ice cube maker and collect in the container. The appliance is not turned Check that the appliance is on.
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice cubes are small. Other domestic appliances that use water are in operation. Avoid using such items as a dishwasher, washing machine or shower at the same time. Check whether the water filter needs changing. See "Water filter" for more information. Check the water pressure. Consult a plumber. The water pressure must be between 25 and 120 psi (1.72-8.25 bar).
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice maker is not producing enough ice or the ice cubes are misshapen. Check the water pressure. The water pressure must be between 25 and 120 psi (1.72-8.25 bar). Contact a plumber. Check that the freezer temperature is not too low. See "Selecting the correct temperature". Change the water filter. See "Water filter". Check the water pressure. The water pressure must be between 25 and 120 psi (1.72-8.25 bar).
Frequently asked questions The appliance is making noises. Issue Possible fault Solution Brrrrr... Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on. Blubb, blubb.... A gurgling noise can be heard when coolant is circulating through the pipes. These noises are not a fault. The noise of the compressor and the coolant circulating in the system is unavoidable. Click....
After sales service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service Department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
Installation instructions To prevent accidents and machine damage read these instructions before installation or use.
Caring for the environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling center about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc., are disposed of safely and kept out of the reach of babies and young children.
Installation Installation site Have the appliance installed by a qualified technician, according to the enclosed installation instructions. The manufacturer is not liable for damage to property due to an incorrect installation or water connection. ,WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. Keep the door closed until the appliance is completely installed and secured as per the installation instructions. Empty weight of your machine: F 1411 SF . . . . . . . .
Installation Base Ventilation A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements: The air intake and outlet must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis. F 1411 SF . . . . . . . . . . 664 lbs (301 kg) To ensure that the appliance is installed securely and functions properly, the base must be flat, level and made of a hard, rigid material. If in doubt, contact Miele.
Installation Installation options Side-by-side There are many different installation options. You are limited only by the design of the kitchen. This appliance can be installed "side-by-side" with another fridge/freezer using a "Merging Kit". The door hinge cannot be exchanged. Single column The appliance can be installed at any preferred location in the kitchen. However, be sure the door will open and close properly in the chosen location. The "Merging Kit" can be obtained from Miele.
Installation . . . with partition The minimum thickness of the partition is 5/8" (16 mm). If there is a partition between the adjacent appliances, then each appliance is to be individually installed within its own niche. The "Merging Kit" can be obtained from Miele. Side panels If one side of the appliance is visible, a side panel must be used. The side panel must be firmly secured to the wall, the floor and the overhead furniture/fixtures before the appliance is placed in the cavity.
Dimensions Niche dimensions F 1411 SF A B 18 1/2" (469.
Dimensions 1. Power supply 2.
Installing the appliance Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation. These installation instructions are intended for use by qualified installers. In addition to these instructions, the appliance must be installed in accordance with all local codes.
Installing the appliance Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. Before installation ,Caution - the appliance is very heavy. Use caution when unpacking and opening the door, danger of tipping. ^ Check that the cavity is square. ^ To protect the base from damage during installation, attach a hard board, linoleum, etc.
Installing the appliance ^ Loosen the bracket that holds the appliance to the pallet. ,Caution! The appliance is no longer secured and may be unstable. ^ Unscrew the screws a on the cover b and pull off the sticker c. ^ Remove the cover b. ^ From the rear of the appliance carefully lift it from the pallet. Once the appliance is on the ground it can be wheeled around.
Installing the appliance If the indicator light does not come on, installation of the module was unsuccessful. In that case, repeat the process. If that does not correct the problem, contact Miele. ^ Pull the antenna d straight out. ^ Guide the cover b over the antenna d and screw on the cover. ^ Angle the antenna d so that it faces to the right or left. If necessary, disconnect the power supply and continue installing the appliance.
Installing the appliance Anti-tip brackets The anti-tip brackets help keep the appliance safely secured to the installation niche to prevent tipping. Two anti-tip brackets are recommended for each appliance or appliance combination (side-by-side). ^ Drill pilot holes: 1 – /8" (3 mm) for 5 x 60 mm wood screws – 1 /16" (2 mm) for 4 x 15 mm wood screws. The distance "D" between the anti-tip brackets b is the width of the appliance. ^ Tightly secure the anti-tip brackets in the niche.
Installing the appliance Securing an alternative anti-tip device – The beam must cover the appliance by at least 2" (50.8 mm). If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. ^ Mark the installation height (lower edge of the beam) on the rear wall of the niche. If possible, always screw the wooden beam to existing studs.
Installing the appliance Sliding the appliance into the installation niche In the case of side-by-side installations, a separate outlet must be used for each appliance. ^ To prevent the power cord from becoming caught: Tie a piece of string to the middle of the power cord and feed it forward under the appliance. When sliding the appliance in, pull the cable forward c. ^ Carefully slide the appliance into the space until the height-adjustable wheels interlock with the anti-tip brackets d.
Installing the appliance Aligning the appliance ^ Align the appliance with the surrounding cabinets. A mark is located on the appliance base and is used as a standard gauge for height adjustment. When adjusting the height, align this mark at 1 1/4" (32 mm) above the floor. ^ Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4" (32 mm). The height-adjustable feet at the front and rear can all be adjusted from the front.
Installing the appliance Note: – Do not twist or jam the appliance inside the niche. When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. Attaching the appliance to the installation niche – The adjustment of the rear feet is aided if the appliance is lifted at the rear (tipped forward slightly). – If using a wooden beam as an alternative anti-tip device, rotate the appliance all the way toward the wooden beam.
Installing the appliance Attaching the toe-kick panel The maximum height of the toe-kick panel is 4" (101 mm) from the top of the floor. Do not cover the ventilation slits in the base panel. Risk of damage to the appliance. Mounting the air separator The air separator keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ If necessary, shorten the three parts of the air separator.
Installing the appliance ^ Position the air separator in the center of the appliance door. ^ From below, screw the air separator firmly onto the door with the 2 screws.
Plumbing All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations. The manufacturer is not liable for damage to property due to an incorrect installation or water connection. The water quality must conform to country requirements for drinking water. – The appliance is only suitable for connection to the cold water supply. – The water pressure must be between 25 and 120 psi (1.72-8.25 bar).
Plumbing Preparing the water connection The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Install the connecting pipe.
Plumbing Connecting the water supply ^ Push the union nut and seal onto the water pipe. When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Push the end of the water pipe into the appliance connection and screw on the union nut, 3. First tighten by hand. When bending the water pipe, be sure not to kink it, otherwise there is a risk of leaks and water damage. Use bending aids.
Electrical connection , Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
RemoteVision The Miele RemoteVision system is designed to send messages directly to Miele and/or your PC. For information on set-up and installation of the RemoteVision module see the "Installation" section of this manual. Be sure your wireless system meets the following requirements – Windows XP® or newer operating system, Mac® OS X 10.3 or higher – Cable or DSL modem – Microsoft® Internet Explorer 6 or higher, Safari 2.0 or higher, Firefox 1.
RemoteVision Accessing the RemoteVision control panel ^ Tap the X button until ; appears in the display. ^ Touch the access button "p" to confirm. ^ Touch the access button "p" so it turns yellow. ^ Note the position of the button X, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible. ^ Place one finger on the position of the X button and hold (the X button will not be visible). ^ While holding down the X button, press the access button "p" once.
RemoteVision MasterCool control panel options for RemoteVision Selectable options Description of function ;- Back ;2 Reboot the module ;3 Reset the module to factory settings ;4 Enter Ad-Hoc Mode Note: If you cannot select any option (other than ; - "back"), the module has not been installed correctly.
Alteration rights reserved / 3408 For the most updated manual see the Miele web site. M.-Nr.
