Installation instructions for 45 cm wide fully integrated dishwashers It is essential to read the operating and installation instructions before installing or using the machine, to avoid the risk of accident or damage to the machine. G M.-Nr.
These installation instructions apply to several different dishwasher models. Model numbers in this booklet refer to the model designation specified on the data plate on the machine (and not the description on the control panel). The data plate is located on the right hand side of the door when open. The model numbers quoted refer only to the basic model number, e.g. the G 603 SC-Vi is described as the G 603.
Contents Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Opening the door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Opening the door when the fixing bracket has been taken off: . . . . . . . . . . . . . 4 1. Fitting protective cover plate to worktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2. Building the dishwasher into a niche . . . . . . . . . .
Installation This dishwasher is specially designed for integration under a worktop run in a fitted kitchen. Opening the door – The front of the dishwasher is designed to take a front panel. It can be fitted with a base unit door front to match the rest of the kitchen. – The dishwasher does not have a plinth facia. The plinth area of the dishwasher needs to be covered either with a plinth facing to match the kitchen furniture or with one which can be ordered as a special accessory.
Installation Building in dimensions Dishwasher models G 803 - G 818 Dishwasher models G 603 - G 618 1) Machine height 890 mm 2) Machine height 840 mm 1) Machine height 870 mm 2) Machine height 820 mm Adjustment range approx. 5 cm (82 - 87 cm total height). Extended machine feet are available at extra cost, (special accessory) where a machine height of 87 to 92 cm is required. Adjustment range approx. 5 cm (84 - 89 cm total height).
Installation 1. Fitting protective cover plate to worktop The plexiglass relfector panel and all other installation items required are included in the accessories pack supplied with the dishwasher. Wood or laminate worktops: The underside of the worktop is protected against steam rising from the machine by a special cover plate. A plastic holder is located on the left hand side of the cover plate for the dishwasher’s control light reflector panel.
Installation ^ Align the cover plate to the front edge of the worktop in the middle of the niche. If the worktop has a very rounded edge, pull the cover plate further forward so that the reflector panel is still visible later on. ^ Press the reflector panel into the plastic holder in the cover plate. ^ Use the tacks supplied to nail the cover plate to the underside of the worktop. Worktops with wood or laminate edging: Nail the tacks through the holes further back from the edge.
Installation Granite or marble worktops: Worktops made from hard materials such as granite or marble do not need the cover plate for protection. The cover plate is only used as a guide for marking the position for the reflector panel plastic holder. ^ Stick the doublesided adhesive strip supplied onto the back of the plastic holder. ^ Remove the protective foil from the adhesive strip and stick the holder to the underside of the worktop at the marked position.
Installation 2. Building the dishwasher into a niche Connection to water and drainage should be sited beside and not behind the dishwasher for accessibility. Connections are usually made in the area under the sink. Many kitchen unit manufacturers provide a cut-out in the base of the sink base unit for the hoses to be fed through. If the base unit has no opening and if there is not an opening through the plinth area for connections, one must be cut.
Installation Securing pieces To ensure stability, the dishwasher must be fixed securely to the neighbouring units (step 5). Two securing pieces are supplied for this purpose. ^ Push the dishwasher right back into the recess. Ensure that the drain hose, inlet hose and the electric cable are laid to reach the connection point without any kinks. ^ Fit the securing pieces into the slots on both the left and right hand sides and turn to the side.
Installation Rear screw feet Front screw feet ^ Use a TORX T20 screwdriver to adjust the rear screw feet to the required height. ^ Adjust the front screw feet manually or with a flat blade screwdriver. Higher = turn clockwise Lower = turn anti-clockwise Several turns are needed to adjust 1 mm in height. Now adjust the feet until the seal on the top of the dishwasher is right up against the underside of the worktop, to which it will be screwed later. Ensure that the dishwasher stands level.
Installation 3. Fitting the matching door front The front of the dishwasher needs to be fitted with a base unit front to match the kitchen furniture. This door front may be a single panel or a two-piece panel, divided to give a dummy drawer facia line. ,The weight of the door front will affect the functioning of the door springs. After fitting it is essential for this to be checked out. See Step 6. Dimensions: Width: to match the door of a 45 cm wide base unit.
Installation Dimension X must be calculated and noted before attaching the fixing bracket. Dimension X is the distance shown on the illustration between the drill hole in the machine outer door panel and the lower edge of the neighbouring unit door. ^ Push the dishwasher into the recess and adjust the height. Fitting the fixing bracket to a door front ^ Lay the door front down with the rear side facing upwards. Draw a vertical line down the middle of the door front rear to use as a guide line.
Installation There are notches on the fixing bracket, marked a in the illustration. ^ Lay the fixing bracket on the rear of the door front, using dimension X for the distance from the bottom, and so that the notches marked a in the middle of the fixing bracket align with the vertical guide line, (see diagram). 14 ^ If necessary pre-drill holes for the screws (Ø 2.5 mm, approx. 10 mm deep). ^ Screw the fixing bracket on securely.
Installation Fitting the door front The door front is correctly fitted when: – the lower lugs on the fixing bracket rest firmly in the lower slits of the dishwasher outer door panel, ^ Hang the door front so that the lower lugs of the fixing bracket fit into the lower slits of the dishwasher outer door panel, and draw slightly upwards.
Installation 4. Adjusting the door front ^ Close the dishwasher door. When fitted the door front can be adjusted up to a maximum of 2 mm upwards or downwards to match adjoining unit fronts. ^ Check the alignment of the door panel again. ^ Open the dishwasher door slightly. ^ If it is not correctly aligned you may need to loosen the screws and re-adjust it to the correct alignment. Once satisfied that the alignment is correct: ^ Open the dishwasher door.
Installation 5. Securing the dishwasher To ensure stability, the dishwasher must be fixed securely to neighbouring units using the fixing brackets. ^ Open the dishwasher door. ^ Screw the countersunk screws (3.5 x 15) supplied through the fixing brackets on the left and right hand sides into the neighbouring units to secure the dishwasher.
Installation 6. Adjusting the door springs ^ Half open the dishwasher door. The door springs are correctly adjusted when the door remains stationary when left open at 45 °. The door springs are easier to adjust when the door is only half open than when it is fully open. If the door drops down, then the door springs need to be tightened. If it closes then the springs need to be loosened. The adjusting screw is located in the upper front strip at the left hand side of the dishwasher.
Installation 7. Matching the plinth facia of a kitchen run ^ Place the plinth facia directly in front of the kitchen run but do not attach. The plinth area of the dishwasher is normally covered with a plinth run matching the kitchen furniture. ^ Carefully open the dishwasher door. If the door front comes into contact with the kitchen plinth when the dishwasher door is opened the plinth facia in the area behind the dishwasher door needs to be cut to size.
Electrical connection ,Please follow the installation instructions carefully. All electrical work should be carried out only by a suitably qualified and competent person, in strict accordance with national and local safety regulations. Ensure power is not supplied to the appliance while installation work is being carried out. This dishwasher is supplied with a mains cable and moulded plug ready for connection to an a.c.
Electrical connection The wires in the mains lead are coloured in accordance with the following code: Green/yellow = earth Blue = neutral Brown = live If the colours of the wires in the mains lead of this appliance do not correspond with the coloured markings identifying the terminals of your plug, proceed as follows: ^ The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol z or coloured green, or green and yello
Plumbing Connection to the water inlet ,Water in the dishwasher must not be used as drinking water. – The dishwasher may be connected to a cold or hot water supply, max. 60 °C. When connected to a hot water supply all programme stages which would otherwise be carried out with cold water (pre-wash and interim rinse) as well as the Pre-wash programme will be carried out with hot water.
Plumbing Drainage Venting the drainage system – The machine drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the machine via the drain hose. ^ Open the dishwasher door fully. – The dishwasher is supplied with an approx. 1.5 m long flexible drain hose with an internal diameter of 22 mm. – The drain hose can be extended using a connection piece and an extra drain hose, (up to max. 4 metres).
Special accessories You would like to... Then you need... ... build the dishwasher into a kitchen which does not have a matching plinth run ...a separate plinth kit available in: white black ... adjust the height of the dishwasher to ...
Technical data Dishwasher model G 603 G 803 Height 81.7 cm (adjustable + 5.0 cm) 84.7 cm (adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) 84 cm (+ 5.0 cm) Width 44.8 cm 44.8 cm Width of building in recess 45 cm 45 cm Depth 57 cm 57 cm Depth with door open 115.5 cm 120.5 cm Weight approx. 47 kg approx. 47.
Technical data Dishwasher model G 618 G 818 Height 81.7 cm (adjustable + 5.0 cm) 83.7 cm (adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) 84 cm (+ 5.0 cm) Width 44.8 cm 44.8 cm Width of building in recess 45 cm 45 cm Depth 57 cm 57 cm Depth with door open 115.5 cm 120.5 cm Weight approx. 48.5 kg approx.
Alteration rights reserved (NovoPlus Vi45) / 2006 M.-Nr.
