Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time. en - GB M.-Nr.
Contents Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Appliance overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Caring for the environment . . . . .
Contents Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Adding detergent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Future updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 For testing institutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Programme chart . . . . .
Guide to the appliance Appliance overview a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i In-operation indicator light d Middle spray arm j Rinse aid reservoir e Air inlet for drying (depending on model) k Dual compartment detergent dispenser f Lower spray arm l Salt reservoir 5
Guide to the appliance Control panel a Time display e Programmes b Delay start button , with indicator light f Programme selector button c "Turbo/Combi tabs" button h Off button V d Check/Refill indicators g On button U with indicator light i In-operation indicator light This instruction book applies to several different dishwasher models. The specific dishwasher models below are referred to as follows: G 1272, G 1282 etc. = G 1XXX G 2272, G 2282 etc.
Warning and Safety instructions Safety with children This appliance conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important information on its safety, use and maintenance. Keep these instructions in a safe place and pass them on to any future owner.
Warning and Safety instructions Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Under no circumstances should you use a damaged appliance. A damaged appliance could be dangerous. ~ The dishwasher must only be plugged into the electricity supply via a suitable switched socket. The electrical socket must be easily accessible after the dishwasher has been installed so that it can be disconnected from the electricity supply at any time.
Warning and Safety instructions ~ This appliance may only be installed in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer. ~ A damaged appliance could be ~ The plastic housing of the water connection contains an electrical component. The housing must not be dipped in water. ~ Unauthorised repairs could result in ~ There are live wires in the water inlet hose. Never cut the water inlet hose, even if it is too long.
Warning and Safety instructions Installation Correct use ~ The dishwasher must be installed and connected in compliance with the installation diagram supplied. ~ Do not use solvents in the ~ The dishwasher must be correctly detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Consult a doctor immediately if detergent has been swallowed or inhaled. aligned to ensure problem-free operation.
Warning and Safety instructions ~ Inadvertently filling the salt reservoir with powder or liquid dishwasher detergent will damage the water softener. Make sure you have picked up the correct packet of dishwasher salt before filling the salt reservoir! ~ Please only use special coarse grained dishwasher salt for reactivation, as other salts may contain insoluble additives which can impair the functioning of the softener.
Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation.
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your household water system is suitable, this dishwasher can be connected to a hot water supply for further economies. If the water is heated by solar panels, for example, this would be energy efficient. However, if your water is heated by electricity we would recommend connection to cold water.
Before using for the first time To open the door To close the door ^ Push the baskets right in. ^ Then lift the door upwards and push until it clicks into position. ^ Pull the handle. If the door is opened during operation all functions are automatically interrupted.
Before using for the first time Water softener In order to achieve good cleaning results, the dishwasher needs to operate with soft water. Hard water results in the build-up of calcium deposits on crockery and in the dishwasher. Mains water with a hardness level higher than 0.7 mmol/l (4 °d – German scale) needs to be softened. This takes place automatically in the integrated water softener. The dishwasher is programmed at the factory for a water hardness level of 2.7 mmol/l (15 °d).
Before using for the first time To programme the water hardness level Each time a button is pressed, one of the indicator lights will flash and light up in the control panel. However, only the indicator lights mentioned in the following programming process stages are significant. The programming procedure can be cancelled at any time by pressing the Off button V. The procedure can then be re-started from the beginning again. ^ Switch the dishwasher off using the Off button V.
Before using for the first time °d German scale mmol/l 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37-45 46-60 61-70 0.2 0.4 0.5 0.7 0.9 1.1 1.3 1.4 1.6 1.8 2.0 2.2 2.3 2.5 2.7 2.9 3.1 3.2 3.4 3.6 3.8 4.0 4.1 4.3 4.5 4.7 4.9 5.0 5.2 5.4 5.6 5.8 5.9 6.1 6.3 6.5 6.7-8.1 8.3-10.8 11.0-12.
Before using for the first time Miele branded products are available from the Miele Spare Parts Department or via the internet at www.miele-shop.com. Before using the appliance for the first time you require: – Approx. 2 litre of water, – Approx. 2 kg dishwasher salt, – Domestic dishwasher detergent, – Rinse aid formulated for domestic dishwashers. Every dishwasher is tested at the factory. There will be residual water in the appliance from this test.
Before using for the first time ^ Remove the lower basket and unscrew the salt reservoir cap. Only open the salt reservoir when you want to fill it with dishwasher salt as water or salt solution will run out of the reservoir when the cap is removed. ^ Fill the reservoir with approx. 2 litres of water (first use only). Salt indicator ^ Fill the salt reservoir with dishwasher salt when the salt indicator light comes on. (If it comes on during a programme, wait until the end of the programme).
Before using for the first time Rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically. If you only ever use combination products containing rinse aid in your dishwasher, you do not need to add rinse aid.
Before using for the first time Rinse aid indicator When the light comes on the reservoir contains sufficient rinse aid for 2 - 3 programmes only. ^ Add rinse aid in plenty of time. If the Combi tabs function has been selected, the rinse aid indicator light will not come on (see "Additional functions, Turbo/Combi tabs"). ^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. ^ Close the flap firmly so that it clicks into place.
Before using for the first time Setting the rinse aid dosage The rinse aid dosage can be set from approx. 0-6 ml. It is set to a recommended setting of approx. 3 ml at the factory. If the Adjust sensor wash function has been activated, the amount of rinse aid dispensed could be higher than that set in the Sensor wash programme. If spots appear on crockery and glassware: ^ Increase the rinse aid dosage. If clouding or smearing appears on crockery and glassware: ^ Decrease the rinse aid dosage.
Loading the dishwasher Note Remove coarse food residues from crockery. There is no need to rinse items under running water. ,Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher. These substances will damage the dishwasher. Crockery can be loaded anywhere in the baskets, but the following notes should be observed: – Do not place crockery and cutlery inside other pieces where they may be concealed. – Load the crockery so that water can access all surfaces.
Loading the dishwasher Items not suitable for dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher. – Craft items, antiques, valuable vases and decorative glassware are also not suitable for dishwashers. – Plastic items which are not heat resistant: the high temperatures in the dishwasher may cause them to melt or lose shape.
Loading the dishwasher Upper basket ,For safety reasons, do not operate the dishwasher without the upper and lower baskets in place. Hinged cup rack ^ To make room for tall items, raise the rack upwards. Positioning rail (depending on model) Glasses can be arranged along the positioning rail to give them some support during the programme. ^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc.
Loading the dishwasher Universal support (depending on model) This support is designed to hold tall glasses and glasses with stems securely. ^ Lower the support and lean tall glasses against it.
Loading the dishwasher Adjusting the upper basket In order to gain more space for taller pieces of crockery in the bottom or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low. This can be useful to help prevent water collecting in deep dishes etc. Ensure, however, that the basket can be inserted smoothly into the cabinet. It is better to adjust the basket before loading it.
Loading the dishwasher Lower basket Hinged spikes ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place delicate glassware in the lower basket. The spikes are used for washing plates and saucers. Both rows of spikes at the back can be lowered to make more room for large items, e.g. pots, pans and dishes.
Loading the dishwasher Removable spiked insert Bottle holder (depending on model) You can remove the spiked insert to make more room for larger items of crockery, e.g. a large, flat pot, or another type of insert. The bottle holder can be used to wash narrow items, e.g. milk and baby bottles. To remove the insert a ^ Pull it upwards by the handle as shown. ^ Place the bottle holder in the position shown in the bottom basket.
Loading the dishwasher Cutlery Cutlery tray (depending on model) If spoon handles do not fit between the holders, then lay them the other way round. ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Spoon heads should be placed in contact with at least one of the serrated retainers on the base of the cutlery tray to ensure that water runs off them freely.
Loading the dishwasher Cutlery basket (depending on model) ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. ^ Fit it into the cutlery basket if required. ^ Place small spoons in the individual slots to either side of the cutlery basket. Cutlery insert for the cutlery basket Use the insert supplied for heavily soiled spoons.
Operation Detergent ,Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid. Miele branded dishwasher cleaning products are available from the Miele Spare Parts Department or via the Internet at www.miele-shop.com. Active ingredients Modern detergents contain various active ingredients, the most important of which are: – Phosphates to prevent calcification. – Alkalis to aid removal of dried on soiling. – Enzymes to break down starch and dissolve protein.
Operation ,Avoid inhalation of powder detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Consult a doctor immediately if detergent has been swallowed or inhaled. Keep detergent and other household agents out of the reach of children at all times. Keep children away from the dishwasher when the door is open.
Operation Switching on Starting a programme ^ Open the stopcock, if it is closed. ^ Select the programme required with the programme selector button. ^ Open the door. ^ Make sure the spray arms are not obstructed. ^ Switch the dishwasher on with the On button U. The On indiciator light U and the indicator for the last used programme light up. Selecting a programme Choose your programme according to the type of load and how dirty it is.
Operation Time display At the end of a programme The duration of the programme selected appears in hours and minutes in the Time display before the programme begins. During the programme, the time left until the end of the programme is displayed. At the end of a programme, the In-operation indicator light will be visible flashing slowly with the door shut. The time displayed may vary with the same programme.
Operation Switching off Unloading the dishwasher At the end of a programme: Dishes tend to break and chip more easily when they are hot. Allow the dishes to cool until they are comfortable enough to handle before unloading them. ^ Open the door. ^ Switch the dishwasher off with the Off button V. The dishwasher will continue to use electricity until it is switched off with the Off button V. If the dishwasher is not going to be used for a longer period of time, e. g.
Operation Interrupting a programme A programme is interrupted as soon as the door is opened. When the door is closed again, the programme will continue from the point it was at before the door was opened. ,Water in the dishwasher may be hot. Danger of scalding. Only open the door if absolutely necessary and exercise extreme caution when doing so. Before closing the door again, leave it ajar for approx. 20 seconds. This will enable the temperature in the wash cabinet to settle.
Additional functions Turbo/Combi tabs Combi tabs The Turbo/Combi tabs button is used for selecting the Turbo and Combi tabs options. To ensure excellent results you can programme your dishwasher for the type of detergent you are using. The Turbo/Combi tabs button is used here for selecting between standard detergents (powder, liquid and 2 in 1 tabs) and combination detergents (3 in 1 / 4 in 1 tabs etc.). ^ Open the door. ^ Switch the dishwasher on with the On button U. The On indicator light U comes on.
Additional functions Delay start ^ Open the door. The start time of a programme can be delayed, e.g. to benefit from economy rates of electricity. A delay start time of between 30 minutes and 24 hours can be selected. ^ Switch the dishwasher on with the On button U. With a delay start time of between 30 minutes and 9 hours 30 minutes, the delay is set in 30 minute stages. For 10 hours or more, it is set in one hour stages.
Additional functions The time starts counting down until the programme start time: in 1 hour steps for delay start periods of over 10 hours, and in minutes for delay start periods of under 10 hours. Starting a programme before the Delay start period has elapsed: At the end of the delay period, the programme selected begins automatically. The time left for a programme to run then shows in the display, the Delay start indicator light , goes out, and the indicator light for the programme selected comes on.
Additional functions Buzzer An audible tone sounds at the end of the programme or if there is a fault. You will hear the buzzer at the end of a programme in bursts of five with a short pause in between. The buzzer will continue to sound for up to an hour if you do not switch the dishwasher off. In the event of a fault, the buzzer will sound continuously for up to two minutes if you do not switch the dishwasher off or correct the fault. The buzzer is activated as standard at the factory.
Additional functions Factory default setting If you have altered any settings from the factory default, you can re-set them back to the factory default settings as follows: ^ Open the door. ^ Switch the dishwasher off with the Off button V. ^ Press the programme selector button in, and whilst holding it in switch the dishwasher on using the On button U. Keep the programme selector button pressed in until the lower right hand programme indicator comes on.
Additional functions Adjust Sensor wash You can adjust the Sensor wash programme so that it will remove stubborn soiling in a lightly soiled load. The message flashing in the Time display shows whether the Adjust Sensor wash function is activated or deactivated. ^ Open the door. – "p 1": The Adjust Sensor wash function is activated. ^ Switch the dishwasher off with the Off button V. – "p 0": The Adjust Sensor wash function is deactivated.
Cleaning and care Check your dishwasher regularly (approx. every 4 - 6 months). This way faults and problems can be avoided. Miele branded cleaning and conditioning products are available from the Miele Spare Parts Department or via the internet at www.miele-shop.com. ,External surfaces of the dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the outer surfaces.
Cleaning and care Cleaning the control panel and door front ,Remove any soiling immediately. If not, it might become impossible to remove and could cause the outer surface to alter or discolour. ^ The control panel should only be wiped with a damp cloth. ^ Clean the front using a damp Miele microfibre E-cloth or with a sponge and a solution of hot water and washing-up liquid. Then dry with a soft cloth.
Cleaning and care Cleaning the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. ,The dishwasher must not be used without all the filters in place. Collection of coarse soil may cause the filters to clog. The level of soiling and time it takes before the filters need cleaning will vary depending on use.
Cleaning and care To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b. ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages. ^ Replace the filter combination so that it lies flat in the base of the wash cabinet. ^ Then turn the handle clockwise, until the arrows line up, to lock the filter combination in place.
Cleaning and care Cleaning the spray arms ^ Remove the lower basket. Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one). ^ Push the top spray arm upwards to engage the inner ratchet. Then unscrew the spray arm.
Problem solving guide With the aid of the following guide, faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Miele Service Department. ,Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations. Unauthorised or incorrect repairs could cause personal injury or damage to the appliance.
Problem solving guide Problem Possible cause The In-operation There may be a indicator is flashing technical fault. quickly. The buzzer is sounding. All the programme indicators flash when the door is open. Fault code FXX shows in the display. The drain pump works even when the door is open. 50 Remedy – Clean the water filter and clean the drain pump and non-return valve as described in "Maintenance". If this does not resolve the problem: – switch the dishwasher off with the Off button V.
Problem solving guide The dishwasher does not fill/drain. Problem Possible cause Remedy The In-operation indicator is flashing quickly. The buzzer is sounding. The Inlet/Drain indicator flashes when the door is open. The stopcock is closed. – Open the stopcock fully. The dishwasher stops during a programme. The In-operation indicator is flashing quickly. The buzzer sounds. The Inlet/Drain indicator flashes when the door is open. Fault code FXX shows in the Time left display.
Problem solving guide General problems Problem The time display is dark. Possible cause The time display has switched off automatically to save energy (Standby mode). Detergent residue is The dispenser was still left in the dispenser at damp when detergent was the end of a added. programme. The detergent dispenser lid cannot be closed properly. At the end of a programme there is a film of moisture on the inside of the door and the interior walls. Make sure the dispenser is dry before adding detergent.
Problem solving guide Noises Problem Knocking noise in the wash cabinet. Possible cause A spray arm is knocking against an item in a basket. Rattling noise in the wash cabinet. Items of crockery are insecure in the wash cabinet. Knocking noise in the water pipes. This may be caused by the on-site installation or the cross-section of the piping. Remedy Interrupt the programme, and rearrange the items which are obstructing the spray arm. Interrupt the programme, and rearrange the items of crockery.
Problem solving guide Unsatisfactory washing result Problem Possible cause The dishes are not The dishes were not loaded clean. correctly. The programme was not powerful enough. Remedy See notes in "Loading the dishwasher" Select a more intensive programme. See "Programme chart". There is some stubborn Use the "Adjust Sensor soiling although most of the wash" function (see crockery is only lightly soiled "Additional functions"). (e.g. with tea stains). Not enough detergent was dispensed.
Problem solving guide Problem Possible cause Remedy Dishes, cutlery and glasses are not dry or are flecked. The amount of rinse aid may be insufficient, or the rinse aid reservoir empty. Replenish the reservoir, increase the dosage or change the brand of rinse aid. See "Before using for the first time". Leave it in for longer. See "Operation". Set the Combi tab function to "Normal", and fill the rinse aid reservoir with rinse aid. See "Additional functions".
Problem solving guide Problem Possible cause Glassware has a brown or blue tinge, and film cannot be wiped off. Glassware is dull and discoloured; film cannot be wiped off. This may be caused by the Change your detergent. detergent. Tea or lipstick stains have not been completely removed. Plastic items are discoloured. There are rust stains on cutlery. 56 The glassware is not dishwasher-proof. The surfaces are affected. The wash temperature of the selected programme was too low.
Maintenance Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet. ,The plastic housing of the water connection contains an electrical component. It must not be dipped in water.
Maintenance Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug. ^ Take the filter combination out of the wash cabinet (see "Cleaning and care - Cleaning the filters in the wash cabinet").
After sales service Repairs Future updates In the event of any faults that you cannot remedy yourself, please contact: The programme update function is designed to enable a service technician to update your appliance's electronics in keeping with advances in technology. – Your Miele dealer, or – the Miele Service Department (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
Programme chart Crockery Mixed, everyday crockery Food deposits All normal food deposits Action required This needs an adaptable programme... Shorter duration... Heat-sensitive glasses and plastic This needs a short programme... Fresh, easily removed food deposits This needs a gentle programme with glass care... Mixed crockery This needs a standard programme... Normal food deposits which have begun to dry on Shorter duration... To save water and energy...
Programme chart Programme Detergent Compartment I 2) Compartment II 2) – 25 ml or 1 tab Quick wash 40°C – 25 ml or 1 tab 3) Sensor wash gentle – 25 ml or 1 tab – 25 ml or 1 tab 3) – 25 ml or 1 tab 10 ml 25 ml or 1 tab – – Sensor wash + Turbo option Light soiling 50°C + Turbo option Energy save Pots & pans 75°C + Turbo option Quick wash 40°C + Turbo option 2) 3) see "Detergent" In some cases, tabs may not dissolve completely.
Programme chart Programme Programme sequence Pre-wash Sensor wash Main wash °C Interim rinse 1 2 Final rinse °C Drying Variable programme sequence, sensor controlled adjustment according to the amount of crockery and level of food deposits If required Quick wash 40 °C 45-65 40 Sensor wash gentle # If required X 65 X 45 X Variable programme sequence with glass care, sensor controlled adjustment according to the amount of crockery and level of food deposits 55 X Light soiling 50 °C If req
Programme chart Consumption 1) Energy Duration 1) Water Cold water connection (15 °C) kWh Hot water connection (55 °C) kWh Litres Cold water connection (15 °C) h:min Hot water connection (55 °C) h:min 1.10-1.60 0.70-1.00 13-22 1:35-2:34 1:23-2:21 0.70 0.22 13 0:38 0:30 0.85-1.20 0.50-0.70 13-22 1:25-1:55 1:14-1:36 1.25 0.90 13 1:32 1:20 1.05 0.70 13 2:54 2:44 1.70 1.20 17 2:39 2:29 1) Values quoted are in accordance with EN 50242.
Optional accessories To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer, the Spare Parts Department or online at www.miele-shop.com (some may be supplied as standard, depending on model). If you would like to … you will need to order … … wash long-stemmed glassware … a glassware insert for the upper basket ... wash bottles, e. g.
Electrical connection Electrical connection U.K. ,All electrical work must be carried out by a suitably qualified and competent person, in accordance with current local and national safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out. The appliance is supplied with a mains cable with moulded plug ready for connection to a 230-240V mains supply.
Plumbing The Miele waterproof anti-leak system Providing your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. Connection to the water supply ,Water in the dishwasher must not be used as drinking water. – The water pressure (flow pressure at the take-off point) must be between 30 and 1000 kPa (0.3 and 10 bar). If the water pressure is too high, a pressure reducer valve must be fitted.
Plumbing Drainage Venting the drainage system – The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. If the on-site drain connection is situated lower than the guide path for the bottom basket rollers in the open door, the drainage system must be vented. Otherwise a siphoning effect during a programme can cause the appliance to empty itself of water. – The dishwasher is supplied with approx. 1.
Technical data Dishwasher model G 1XXX G 2XXX Height 80.5 cm (adjustable + 6.5 cm) 84.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) Width 59.8 cm 59.8 cm Width of building-in recess 60 cm 60 cm Depth 57 cm 57 cm Weight Max. 55 kg Max.
Alteration rights reserved/ G1272/G2272 / 0509 M.-Nr.
