Operating Instructions Diamante G 2150 To prevent accidents and machine damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Before using for the first time. . . . . . . . . . . .
Contents Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Technical faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Problems water intake/drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 General problems with the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Sounds . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS When using your dishwasher, follow basic precautions, including the following: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Electrical Safety ~ Before installation, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubt.
IMPORTANT SAFETY INSTRUCTIONS Installation ~ , WARNING - Fire hazard ~ The dishwasher must be installed Do not cover or crush the plug of the appliance. Ensure that the cabinet opening for the dishwasher provides ample space for the plug. Installing the dishwasher in a tight space may crimp the power cord or put pressure on the plug which could cause overheating. and connected in compliance with the installation instructions.
IMPORTANT SAFETY INSTRUCTIONS Use ~ Only use detergents and rinse aids ~ To reduce the risk of injury, do not recommended for residential dishwashers. Keep all detergents and rinse aids out of the reach of children. allow children to play in, on or near the dishwasher. Do not inhale or swallow detergents. ~ Only use the dishwasher if all panels ~ Dishwasher detergents contain irritant are properly in place. ~ Do not tamper with the controls.
Guide to the dishwasher a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i Child Safety Lock in the door handle (not visible) d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm j Rinse aid reservoir k Dual compartment detergent dispenser 7
Guide to the dishwasher Control panel a Program selection d Check / Refill indicators b Program button e Program cycle indicators c Start/Stop button with indicator f s button (On/Off) 8
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption and the gentlest washing of china and crystal, connect the dishwasher to a cold water source. ^ For fastest possible wash times, yet higher energy consumption, connect the dishwasher to a hot water source. ^ Make full use of the baskets without overloading for the most economical washing.
Before using for the first time To open the door Child Safety Lock ^ Press the release catch inside the door grip. The Child Safety Lock is designed to prevent children from opening the dishwasher. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will restart. To close the door ^ Push the baskets in. ^ Lift the door and push until it clicks into place. 10 ^ To lock the door, push the slider below the door grip to the right.
Before using for the first time Rinse aid Rinse aid is needed to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. ,Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using "2 in 1" detergents rinse aid is not needed.
Before using for the first time Rinse aid indicator Adjusting the dosage When the Rinse aid indicator first comes on, there will be enough rinse aid left for 2 - 3 washes. The dosage selector is preset to 3. This dispenses approximately 3 ml of rinse aid per program. It can be adjusted from 1 to 6. – Use a higher setting if spots appear on dry glassware. – Use a lower setting if streaking appears on dishes or glasses. ^ Turn the dishwasher off "s".
Before using for the first time ^ Press the program button three times. The lowest program indicator flashes three times in intervals. The "Rinse" indicator flashes three times in intervals. A rinse aid amount of 3 ml is set by default. The amount set can be recognized by the flashing rhythm of the "Rinse" indicator (see table).
Loading the dishwasher ,Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher. Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher. Wax, grease and paint will cause permanent discoloration and damage to the dishwasher. ^ Scrape food from dishes before placing them in the dishwasher, rinsing is not necessary. ^ Some foods contain natural dyes, e.g. carrots or tomatoes.
Loading the dishwasher Items not recommended for dishwashing – Cutlery with wooden handles – Wooden cutting boards – Glued items such as old knives with handles glued together around the shank of the blade – Handmade craft items, antique, metal trimmed or decorative glassware Glassware: – There are no standard guidelines for washing glassware, when in doubt wash by hand. – When purchasing new dishes, glasses and cutlery, make sure they are dishwasher safe.
Loading the dishwasher Cutlery tray (depending on model) Spoons with thick handles may have to be placed as knives and forks with their heads in the holders ^ Arrange the cutlery as shown in the cutlery tray. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge down and forks with the prongs between the holders.
Loading the dishwasher Cutlery basket Spoon inserts for the cutlery basket (depending on model) ^ For best cleaning results, cutlery should be placed in the basket with the handles down. Knives and forks should be loaded with the pointed end down to prevent injuries. The supplied insert is designed to wash heavily soiled spoons. The individual slots allow the water to better reach the surface of each spoon. ^ Attach the insert when needed to the cutlery basket.
Loading the dishwasher Upper basket ,Always use the dishwasher with the upper and lower basket inserted. Cup racks ^ Raise the rack to make room for tall glasses. Lower it to double stack smaller pieces. Coffee bar (depending on model) Glasses can be leaned against the coffee bar for a secure stand. ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls and flat pans.
Loading the dishwasher Adjusting the upper basket The upper basket can be raised or lowered to accommodate tall items. The basket can also be angled to fit tall items in both, the upper and lower baskets. The angles should not be set to opposite extremes. This will block the middle spray arm. Take care when sliding the basket in and out in this position. Depending on the setting of the upper basket, a variety of plate dimensions can be accommodated.
Loading the dishwasher Lower basket Foldable spikes ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small plates and saucers can also be arranged in the lower basket. The foldable spikes can be used for small plates and saucers. Dishwashers with cutlery tray Two rows of spikes can be folded down, to create more room for larger dishware, e.g. pots, pans and bowls. Dishwashers with cutlery basket ^ Press the yellow lever down a and fold down the spikes b.
Loading the dishwasher Removable spike insert The spike insert can be removed in order to make room for larger tableware or to use a different insert. Removeable plateguard plus with stemguard (depending on model) This insert is ideal for cups, glasses, plates, bowls, pots and pans. Removing the insert ^ To remove the insert, gently pull the handle upwards. Inserting the insert b ^ Slide the hitches of the insert under the struts of the lower basket. ^ To arrange tall items the cup rack can be raised.
Loading the dishwasher Vase / Bottle insert (depending on model) The vase / bottle insert can be used to rinse narrow items, e.g. vases, baby bottles, etc. Removing the insert a: ^ To remove the insert, gently pull the handle upwards. Inserting the insert b: ^ Place the insert into the lower basket. ^ Slide the hitches of the insert under the struts of the lower basket. ^ Push down on the handle to snap the insert into position. ^ Place the insert into the lower basket as shown in the illustration.
Basket accessories Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele. Depending on the model some accessories come standard with the machine.
Use Detergent ,Dishwasher detergents contain irritant and corrosive ingredients. Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Fill the detergent dispenser only when you are ready to start the dishwasher. ,Only use detergents formulated for domestic dishwashers. Use only the recommended amount of detergent. Continued use of too much detergent may cause machine damage. 24 You can use powder, gel or tab detergents.
Use Adding detergent ^ To open, press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. The horizontal marks in compartment II indicate the levels of approximately 1 ¼ and 2 tablespoons (20 and 30 ml) respectively. Compartment I holds a maximum of 2 teaspoons (10 ml).
Use Turning on Starting a program ^ Make sure the spray arms can rotate freely. ^ Select the desired program with the program selector button. ^ Close the door. The indicator of the selected program lights. ^ Open the water supply, if it is closed. ^ Turn the dishwasher on s. The "Start/Stop" indicator flashes and the indicator of the last set program lights. Selecting a program Choose your program according to the type of load and soiling. The "Program guide" describes the programs and use.
Program guide Program When to use Program sequence Main wash Prerinse 1 Pots & Pans For normally soiled pots and pans with dried on food, also for heavily soiled dishware, use 120% of normal detergent dose Run-time 125 min Normal For normally soiled dishware Run-time 129 min Economy 2 Interim rinse 1 2 Final rinse Drying x x x x x x x x x x For normally soiled dishware, energy saving program with a long soaking time and a low temperature Run-time 95 min x x x x SaniWash Extende
Use At the end of a program Interrupting a program When the program has finished the "End" indicator lights. A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. Dishes tends to chip if removed still hot from the dishwasher. ^ Let the dishware cool by opening the door slightly. The dishes will cool much faster. ^ Open the dishwasher and unload the dishes. ^ Turn the dishwasher off s.
Additional functions Factory default All settings can be reset to the factory default. ^ Turn the dishwasher off s. The "Rinse" indicator shows if a setting was changed. – The "Rinse" indicator flashes: All settings are the factory default. ^ Press the "Start/Stop" button and at the same time turn the dishwasher on s. Hold the "Start/Stop" button until the "Start/Stop" indicator comes on. – The "Rinse" indicator is off: At least one setting was changed. If it does not come on, start over.
Frequently asked questions With the aid of the following guide, minor problems can be fixed without a service call. ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Issue The Start/Stop indicator does not flash after the dishwasher is turned on with s. Possible fault The machine is not plugged in. The fuse has tripped.
Frequently asked questions Problems water intake/drain Issue The "Intake/Drain" indicator flashes and lights alternately. The dishwasher stops running. The "Intake/Drain" indicator flashes. Possible fault The water supply is closed. Solution Open the water supply all the way. Before fixing the fault: – Turn the dishwasher off s. Fault in the water – Open the water supply all the intake. way. – Clean the water intake filter, see "User Maintenance Instructions".
Frequently asked questions General problems with the dishwasher Issue Detergent is left in the dispenser at the end of a program. The detergent lid cannot be closed properly. The door and the interior walls are still wet after a program has finished. Possible fault The dispenser was damp when detergent was added. Detergent residue is blocking the catch. Solution Dry the dispenser before adding detergent. Remove the residue.
Frequently asked questions Sounds Issue There is a knocking noise in the wash cabinet. There is a rattling noise in the wash cabinet. There is a knocking noise in the water pipes. Possible fault Solution The spray arm is hitting an Interrupt the program, item in the basket. rearrange items blocking the spray arms. Items are not secure in the Interrupt the program and wash cabinet. rearrange loose pieces. This may be caused by This has no effect on the the installation or the dishwasher.
Frequently asked questions Poor cleaning results Issue Possible fault The dishes are not The dishes were not loaded clean. correctly. The program was not powerful enough. Not enough detergent was dispensed. The spray arms are blocked by items. The triple filter in the base of the wash cabinet is not clean or not correctly inserted. The spray arm jets might be clogged. The drain pump or the non-return valve is blocked. Wash water will run back into the wash cabinet. Glasses and cutlery show streaks.
Frequently asked questions Issue Possible fault Dishes are still wet, glasses and cutlery are spotted. The rinse aid setting may be too low, or the rinse aid reservoir is empty. White residue is visible on cutlery and dishes. Clouding occurs on glassware and film can be wiped off. Solution Increase the dosage, refill the reservoir or switch the rinse aid product when refilling, see "Before using for the first time". Dishes were taken out too Leave dishes in longer, see soon. "Use".
Frequently asked questions Issue Possible fault Glasses are discolored and the film cannot be wiped off. Glasses are dull and discolored, film cannot be wiped off. Detergent ingredients have Use a different detergent. been deposited on the glassware. Tea or lipstick stains have not been completely removed. The wash temperature of the selected program was too low. The detergent has a low bleaching effect. Natural dyes e.g. from vegetables may be the cause.
After sales service Repairs MieleCare In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. MieleCare, our Extended Service Contract program, gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts.
Transport To transport the dishwasher, e.g. when moving to a new home, note the following: – Empty the dishwasher. – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – Transport the dishwasher in the upright position. If unavoidable it may be transported on its back. Do not transport it on its side or on the door. Residual water in the machine could leak and cause electrical damage.
User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use.
Cleaning and Care Exterior Check and clean your dishwasher regularly (approx. every 4-6 months). This will help avoid problems and faults. ,Abrasive cleaning agents, glass cleaning agents, all-purpose cleaners, thinner or ammonium cleaners should not be used on the dishwasher. They will damage the surface. Wash cabinet Generally, the wash cabinet is self cleaning if the correct amount of detergent is used.
Cleaning and Care Triple filter system The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones). ,The machine must not be used without all the filters in place! ^ Check and clean the filter system every 4-6 months or whenever a foreign object is trapped.
Cleaning and Care To clean the inside of the filter, the flap must be opened. ^ Return the filter so it lies flat in the base of the wash cabinet. ^ Push the clips together a and open the flap b. ^ Lock the filter by turning the handle clockwise. ^ Rinse under running water. ,The triple filter system must be ^ Close the flap so that the clip engages. inserted and locked. Large particles could get in the circulation system and cause a blockage.
Cleaning and Care Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). ^ Press the top spray arm up to engage the inner ratchet and unscrew the spray arm. ^ Lift up the middle spray arm, a, to engage the ratchet and unscrew the spray arm, b. ^ Remove the lower basket.
Cleaning and Care Cleaning the water inlet filter A filter is incorporated into the intake hose attached to the dishwasher’s shut off valve. If your water is hard or the pipes contain sediment, this filter may clog and prevent enough water from entering the wash cabinet. ,The plastic housing of the water connection contains electrical wiring. Do not submerge the housing in liquid. Do not cut the intake hose or submerge it in liquid.
Cleaning and Care Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system"). ^ Use a jug or bowl to scoop water out of the wash cabinet. The drain pump is beneath the non-return valve (see arrow). ^ Remove all foreign objects from the drain pump (glass or bone splinters).
Installation Instructions For installation of the dishwasher please refer to the Installation Sheet supplied with these instructions.
Help to protect the environment Disposal of the packing material The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! 48 Disposal of an old machine Old appliances may contain materials that can be recycled.
Electrical connection ,Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held responsible for unauthorized work. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the mains. Danger of overheating! See data plate on the right side of the door.
Plumbing Connection to the water supply ,Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperature required by the wash program. This allows for connection of the machine to either a hot or cold water source. For lowest energy consumption connect the dishwasher to a cold water source. For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source. All programs use hot water in the rinse cycles.
Plumbing Drainage Venting the drainage system – The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. If the dishwasher drain hose is connected to a floor drain or to a drain pipe that is less than 8" (20 cm) above the floor, the drain must be vented. Otherwise the water inside the dishwasher may siphon out during the wash program. – The dishwasher is equipped with a 5 ft (1.
Alterations reserved/1008 G 2150 For the most updated manual see the Miele web site. M.-Nr.
