Operating Instructions Dishwashers To prevent accidents and machine damage, read these instructions before installation or use. en-US HG07 M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS ............................................................ 6 Guide to the appliance ...................................................................................... Appliance overview ............................................................................................. Control panel ....................................................................................................... Display functions .................................................
Contents Loading the dishwasher.................................................................................... General information ............................................................................................. Loading examples ............................................................................................... Upper basket....................................................................................................... Adjusting the upper basket ..........................
Contents Cleaning the filters............................................................................................... 65 Cleaning the drain pump ..................................................................................... 67 Frequently Asked Questions ............................................................................ Technical faults.................................................................................................... Fault messages ...................................
IMPORTANT SAFETY INSTRUCTIONS This dishwasher complies with all current local and national safety requirements. Inappropriate use can, however, lead to personal injury and material damage. Please observe the installation sheet and read the operating instructions carefully before setting up the dishwasher and using it for the first time. They both contain important information on the installation, safety, use, and maintenance of the machine. This prevents both personal injury and damage to the dishwasher.
IMPORTANT SAFETY INSTRUCTIONS Appropriate use This dishwasher is intended for use in domestic households and similar residential environments. This dishwasher is not suitable for outdoor use. This dishwasher is intended for use at altitudes of up to 1,300 ft (4,000 m) above sea level. This dishwasher must only be used for cleaning domestic dishes and cutlery. All other types of use are not permitted.
IMPORTANT SAFETY INSTRUCTIONS Safety with children Children must be kept away from the dishwasher unless they are constantly supervised. Children must not be allowed to clean or maintain the appliance. Children should be supervised in the vicinity of the dishwasher. Never allow children to play with the dishwasher. There is a danger that children might shut themselves in the dishwasher.
IMPORTANT SAFETY INSTRUCTIONS Technical safety Unauthorized installation, maintenance, and repairs can cause considerable danger for the user. Installation, maintenance, and repairs should only be carried out by a Miele authorized technician. Damage to the dishwasher can compromise your safety. Before using the dishwasher and in particular following transport, check it for any visible damage. Never use a damaged dishwasher.
IMPORTANT SAFETY INSTRUCTIONS Ensure that the connection data on the dishwasher’s data plate (fuse rating, frequency, and voltage) match the electricity supply. This data must correspond in order to avoid the risk of damage to the dishwasher. Compare these before connecting the appliance to the electricity supply. If in any doubt, consult a qualified service technician.
IMPORTANT SAFETY INSTRUCTIONS The water-connection pressure needs to be between 7.25 and 145 psi (50 and 1,000 kPa). A damaged dishwasher could be dangerous. If the dishwasher gets damaged, turn it off at the electricity supply immediately and contact your Miele dealer or Miele Customer Service. The manufacturer’s warranty may be invalidated if the appliance is not repaired to Miele authorized service standards. We recommend replacing defective components with original parts.
IMPORTANT SAFETY INSTRUCTIONS Correct installation The dishwasher must be installed and connected in compliance with the supplied installation sheet. Be careful before and while installing the dishwasher. Some metal parts pose a risk of injury/being cut. Wear protective gloves. The dishwasher must be correctly aligned horizontally to ensure problem-free operation.
IMPORTANT SAFETY INSTRUCTIONS Dishwasher detergents can cause burning on the skin and in the eyes, nose, mouth, and throat. Avoid contact with detergents. Do not inhale powder detergents. Do not swallow dishwasher detergents. Seek medical attention immediately if detergent has been swallowed or inhaled. Avoid leaving the dishwasher door open unnecessarily. You could injure yourself on the opened door or trip over it. Do not sit, stand, or lean on the opened door. The dishwasher could tip over.
IMPORTANT SAFETY INSTRUCTIONS In dishwashers with a cutlery basket (depending on model), knives and forks should be placed with the handles upwards in the basket for safety reasons. Knives and forks placed with the handles downwards pose a danger of injury. However, cutlery placed handle down in the cutlery basket will come out cleaner and drier.
IMPORTANT SAFETY INSTRUCTIONS Disposal of your old dishwasher Remove the door of the dishwasher so that children cannot become trapped inside. FCC Declaration of Conformity These devices comply with FCC Rules Part 15. This equipment has been tested and found to be in compliance with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules of Operation and is subject to the following conditions: These devices may not cause harmful interference.
Guide to the appliance Appliance overview a Door locking pins g Bottom spray arm b Top spray arm h Filter combination c 3D MultiFlex Cutlery Tray (depending on model) i Salt reservoir d Upper basket (depending on model) k Rinse aid reservoir e Middle spray arm l Detergent compartment f Aeration valve 16 j Data plate
Guide to the appliance Control panel a In-operation indicator light For indicating an ongoing wash program when the door is closed. g Express button For reducing the program cycle time. h IntenseZone button b Display Increases cleaning performance in For further information, see “Display the lower basket. functions” under “Guide to the appli- i Program program selection button ance”. For program selection. c buttons j Program selection For program selection.
Guide to the appliance Display functions The display is used to select or set the following: - the program - the Timer - the Settings The OK button is used to confirm a message or setting and also to move to the next menu or another level. Under More, a scroll bar will appear in the right of the display. This offers further options. These options can be shown using the buttons.
Caring for the environment Disposal of the packing material The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of your old appliance Electrical and electronic appliances contain valuable materials.
Before using for the first time Every dishwasher is tested at the factory. There will be residual water in the machine from this test. It is not an indication that the dishwasher has been used previously. Opening the door In some programs the door automatically opens slightly to assist the drying process. This function can be deactivated, if preferred (see “AutoOpen” under “Settings”). Risk of scalding due to hot water. During operation, water in the dishwasher may be very hot.
Before using for the first time Basic settings Setting the water hardness Turning on the dishwasher The display changes to the screen for setting the water hardness. Open the door. Turn the dishwasher on with the button. The welcome screen will appear when the dishwasher is turned on. For further information about the display functionality, see “Display functions” under “Guide to the appliance”. Setting the language The display will change automatically to the screen for setting the language.
Before using for the first time Finally, prompts will appear in the display. After confirming these prompts with OK, the messages Refill salt and Refill rinse aid may appear. Add salt and rinse aid if necessary (see “Reactivation salt” and “Rinse aid” under “Before using for the first time”). Select OK to confirm the messages. The program selected will appear in the display briefly and the indicator light for the program selected will come on.
Before using for the first time Reactivation salt In order to achieve good cleaning results, the dishwasher needs to operate with soft water. Hard water results in the build-up of calcium deposits on dishes and on the inner surfaces of the machine. Domestic water with a hardness level higher than 5 gpg (5 °dH – German scale) must be softened. This occurs automatically in the integrated water softener. The water softener is suitable for a water hardness level of up to 73 gpg (70 °dH – German scale).
Before using for the first time Filling the salt reservoir Before filling the salt reservoir for the first time, you must fill it with approx. 1/2 gallon (2 l) of water to enable the salt to dissolve. Once the dishwasher has been used once, there is always sufficient water in the salt reservoir. Remove the lower basket from the wash cabinet and unscrew the salt reservoir cap. Danger of corrosion due to saline solution. Water or saline solution will run out of the reservoir when the cap is opened.
Before using for the first time Refilling the salt Fill the salt reservoir with reactivation salt when Refill salt appears in the display. Confirm with OK. The salt refill indicator will go out. Danger of corrosion due to saline solution. Salt solution that runs out can cause corrosion in the wash cabinet and to the wash items. Each time you remove the salt reservoir cap, you must run the QuickIntenseWash program with the Express program option selected without wash items in the dishwasher.
Before using for the first time Rinse aid Rinse aid is necessary to ensure that water does not cling and leave marks on dishes during the drying phase, and helps dishes dry faster after they have been washed. Rinse aid is poured into the container and the amount set is dispensed automatically. Liquid dish soap or detergent can cause damage. Liquid dish soap and detergent can damage the rinse aid reservoir. Only fill it with rinse aid formulated for domestic dishwashers. Risk of acid damage.
Before using for the first time Adding rinse aid Close the lid firmly until you hear it click into place. Otherwise, water can enter the rinse aid reservoir during a program. Wipe up any spilled rinse aid. This prevents excess foam developing during the next program. You can adjust the rinse aid dosage for best wash results (see “Rinse aid” under “Settings”). Filling the rinse-aid reservoir Press the yellow button on the lid of the rinse aid reservoir.
Settings You can alter the dishwasher’s controls to suit changing requirements by adjusting the settings. The settings can be altered at any time. Opening the settings menu Turn the dishwasher on with the button if it is turned off. Use the Program button to select the More option. The first of the additional programs will appear in the display. Select the Settings menu option using the buttons and confirm with OK. The first option in the Settings menu will appear in the display.
Settings Language Water hardness The display can be set to appear in one of several different languages. Your dishwasher is fitted with a water softener. You can change the language used in the display and also the country via the Language sub-menu. - The dishwasher must be programmed to the correct water hardness for your area. The flag after the word Language serves as a guide if a language that you do not understand has been set.
Settings 30 °d gr/gal °fH Display 11 11 20 11 12 13 22 12 13 14 23 13 14 15 25 14 15 16 27 15 16 17 29 16 17 18 31 17 18 19 32 18 19 20 34 19 20 21 36 20 21 22 38 21 22 23 40 22 23 24 41 23 24 25 43 24 25 26 45 25 26 27 47 26 27 28 49 27 28 29 50 28 29 30 52 29 30 31 54 30 31 32 56 31 32 33 58 32 33 34 59 33 34 35 61 34 35 36 63 35 36 38 65 36 37-45 39-47 66-80 37-45 46-59 48-62 82-105 46-59
Settings Rinse Aid Display brightness You can adjust the rinse aid dosage for best results. The rinse aid dosage can be set from 0 to 6 ml. 3 ml is the factory default setting. You can set the display brightness to one of 7 different levels. The rinse aid dosage can turn out to be higher than the set value due to the automatic adjustment of the program. If spots appear on dishes and glassware: - Increase the rinse aid dosage.
Settings Refill reminders Extra clean If you only ever use combination detergent products or automatic dispensing using Miele PowerDisks (if available), you can turn off the refill reminders for reactivation salt and rinse aid if you wish. You can choose this function to increase the cleaning performance of the programs. Please make sure that if you stop using combination detergents, you refill the reactivation salt and rinse aid. Turn the refill reminders back on.
Settings 2nd interim rinse Software version You can choose this function to increase the cleaning performance of the programs with a second interim rinse. You can display the electronic software version of your dishwasher for technical support purposes. When this function is activated, water consumption may increase. Showroom program For demonstration purposes only. If this function is switched on, it will be applied to all programs until it is switched off again.
Caring for the environment Energy-saving dishwashing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your machine by following these tips: - Washing in a dishwasher generally uses less water and energy than washing by hand. - There is no need to pre-rinse items under running water, and this unnecessarily increases water and energy consumption. - Make full use of the basket capacity without overloading the dishwasher.
Loading the dishwasher General information Remove coarse food residues from dishes. There is no need to pre-rinse items under running water. Damage can be caused by ash, sand, wax, lubricating grease, or paint. These substances will contaminate the dishwasher and can then no longer be removed. Do not wash items soiled with these substances in the dishwasher.
Loading the dishwasher Wash items not suitable for dishwashers: Damage due to caustic alkaline - Craft items, antiques, valuable vases, and decorative glassware. Such items are not suitable for dishwashers. detergents. Aluminum parts (e.g., the grease filters of ventilation hoods) can be damaged by caustic alkaline detergents. In extreme cases, there is a risk of an explosive chemical reaction (such as an explosive oxyhydrogen gas reaction).
Loading the dishwasher Loading examples Loading for 10 standard place settings with cutlery tray Upper basket Lower basket Cutlery tray 37
Loading the dishwasher Loading for 16 standard place settings with cutlery tray Upper basket Cutlery tray 38 Lower basket
Loading the dishwasher Upper basket Loading the upper basket Risk of damage due to water leakage. If you run the dishwasher without the upper basket, water can leak out of the dishwasher. Only run the dishwasher with the upper basket in place (except during the Tall items program, if available). Loading the FlexCare cup rack You can put cups, small bowls, and flat dishes on the FlexCare cup rack. Glasses can be arranged along the cup rack so they sit securely during the program.
Loading the dishwasher Adjusting the FlexCare cup rack You can set the height and depth of the cup rack at 2 different levels so that it can accommodate larger cups and so that taller items can be placed underneath it. Pull the cup rack upwards and click it into the desired position (see arrow). 40 Loading the silicone elements of the FlexCare cup rack The silicone elements in the cup rack are specially designed to hold tall glasses with long stems securely.
Loading the dishwasher Lowering the spikes On both right-hand rows of spikes, you can lower every other spike to make it easier to arrange larger dishes, like cereal bowls. Press the yellow lever downward , and then lower the dark gray spikes . Place the bowls vertically in the row of spikes.
Loading the dishwasher Adjusting the upper basket To raise the upper basket: In order to gain more space for taller items in the lower basket or upper basket, the upper basket can be adjusted on 3 levels with 3/4 " (2 cm) between each level. Lift the basket until it clicks into place. The upper basket can also be set at an angle so that water can run off freely from recesses. Make sure, however, that the basket can slide smoothly in and out of the wash cabinet. Pull out the upper basket.
Loading the dishwasher Lower basket Loading the lower basket Place larger and heavier items such as plates, serving platters, saucepans, bowls, etc., in the lower basket. Glasses, cups, and small plates and saucers can also be placed in the lower basket. Loading the MultiComfort area The rear section of the lower basket is used for washing cups, glasses, plates, and pots. Place very large plates in the center of the lower basket.
Loading the dishwasher Lowering the spikes Loading the FlexCare glass holder The rows of spikes at the front are used for loading plates, soup bowls, platters, dessert bowls, and saucers. The silicone elements in the glass holder provide a stable and secure hold for delicate stemware. Both right-hand rows of spikes can be lowered to make more room for large items such as pots, pans, and serving dishes.
Loading the dishwasher Cutlery tray See “Loading the dishwasher, Loading examples” for examples of how to load dishware and utensils. Load the utensils into the 3D MultiFlex Tray. Loading the 3D MultiFlex Tray To make unloading easier, utensils should be grouped in zones, one for knives, one for forks, one for spoons, etc. Spoon heads should be placed in contact with at least one of the serrated retainers on the base of the cutlery tray to ensure that water runs off them freely.
Detergents Active ingredients Damage caused by using unsuitable detergents. Detergents that are not suitable for domestic dishwashers can cause damage to the dishwasher or to the wash items. Only use detergents formulated for domestic dishwashers. Modern detergents contain various active ingredients, the most important of which are: - Water softening complexing agents to prevent calcification. - Alkalis to aid removal of dried-on soiling. - Enzymes to break down starch and loosen protein.
Detergents Risk of chemical burns from de- Detergent dispensing tergent. Dishwasher detergents can cause burning on the skin and in the eyes, nose, mouth, and throat. Avoid contact with detergents. Do not inhale or ingest powder detergents. Do not swallow dishwasher detergents. Seek medical attention immediately if detergent has been swallowed or inhaled. Keep children away from detergents. Detergent residues could still be present in the machine.
Detergents Adding detergent The detergent must not cause the detergent-compartment lid to get stuck. This can prevent the lid from opening during the program. Do not overfill the detergent compartment. Ensure that the detergent packaging is properly closed after use. This prevents the detergent from getting damp and clumping together. Press the yellow button on the lid of the detergent compartment. The lid will spring open. The lid will also open at the end of a program.
Operation Turning on the dishwasher Selecting a program Turn on the water supply if it is turned off. Choose your program according to the type of load and the degree of soiling. Open the door. The different programs and their uses are described under Program overview. Make sure the spray arms can rotate freely. Press the button. The program selected will appear in the display briefly and the indicator light for the program selected will come on.
Operation Display of program duration Starting a program The estimated duration of the selected program appears on the display before the program begins. If the door is opened during the program, the time left until the end of the program is displayed. Start the program by closing the door within 4 seconds of the last press of a button. If necessary, confirm the previously displayed message with OK.
Operation End of program Energy management At the end of a program, the in-operation indicator light will be flashing slowly with the door shut. The audible signal may also be sounding. To save energy, the dishwasher will switch off automatically 10 minutes after the last time a button is pressed or after the end of a program. The in-operation indicator light will go out 10 minutes after the end of the program if the door is closed. You can turn the dishwasher back on again with the button.
Operation Turning off the dishwasher Unloading the dishwasher Open the door. Dishes tend to break and chip more easily when they are hot. Allow the dishes to cool until they are comfortable enough to handle before unloading them. The dishwasher can be turned off at any time using the button. Confirm the query Turn appliance off with OK. Turning the dishwasher off during a program stops the program. You can also do this to stop an ongoing timer. Risk of damage from leaking water.
Operation Interrupting a program A program will be interrupted as soon as the door is opened. After 4 seconds, the indicator light of the selected program and the time display will flash. Press the Program button and close the door within 4 seconds. The program will continue from the point at which it was interrupted. Risk of scalding due to hot water. During operation, water in the dishwasher may be very hot. During operation, only open the door with extreme caution.
Options Timer Activating the timer You can set the start time of a program. The program start time can be delayed for between 30 minutes and 24 hours. With start-time delays between 30 minutes and 3 hours, the delay can be set in 30 minute stages. It is set in hours for periods longer than this. Open the door. During manual detergent dispensing, the detergent will clump together if the detergent compartment is not dry, and this may mean it is not fully rinsed out.
Options After you have activated the timer, all the displays will turn off after a few minutes to save energy. Press the button to switch the display back on again for a few minutes. Open the door if you need to check how long the timer has left to run. The time up until the program starts will count down in the display in hours for durations above 10 hours, and in minutes for durations below 10 hours. At the end of the delay period, the program selected begins automatically.
Program overview Program When to use Program sequence Prewash Main wash Interim rinse °F/°C 1 Final rinse Drying °F/°C Program for regular use to completely wash a full load of normally soiled dishes with the ability to adjust energy and water consumption based on the soil load of the dishes. 140– 158/60 –70 133– 149/56 –65 Pots & Pans For heavily soiled dishes and normally soiled pots,pans and utensils with dried on residue; use 20% more detergent than recommended.
Program overview 2 2 Consumption Energy 2 Duration Water Cold water Hot water Cold water Hot water 50°F/10°C 120°F/49°C Gallons/Liters 50°F/10°C 120°F/49°C kWh kWh h:min h:min 1.06 1.20 3.2/12.1 3:04 2:43 1.40 1.55 3.4/13.0 3:29 3:11 0.90 1.05 3.3/12.5 2:45 2:25 1.10 1.15 2.9/11.0 1:13 0:58 0.85–1.25 0.90–1.40 1.7–3.2/6.5–12.0 2:28–3:45 2:16–3:27 0.01 0.15 1.1/4.0 0:21 0:21 Values were calculated under standardized testing conditions.
Program options Selecting program options Express You can use program options to adjust the programs. The Express option reduces the program cycle time. To do this, you can select or deselect the program options before running the program. In order to achieve optimum cleaning results, the temperature, and therefore the energy consumption, will increase with this option. Open the door. Turn the dishwasher on with the button. The indicator light next to the selected program will come on.
Cleaning and care Check the condition of your dishwasher regularly (approx. every 4– 6 months). This helps to avoid faults and problems. Cleaning the wash cabinet Damage due to unsuitable clean- If, despite this, limescale or grease deposits build up in the cabinet, these can be removed with a proprietary dishwasher cleaner (available from the Miele Customer Service or Miele's online store). Follow the dosage recommended by the manufacturer on the packaging. ing agents.
Cleaning and care Hygiene cycle The frequent use of low-temperature wash programs increases the risk of contamination and odors inside the wash cabinet. If you repeatedly use low-temperature programs, you should regularly run a high-temperature program. This is to prevent contamination and odors. You can activate or deactivate a Hygiene info message (see “Settings – Hygiene cycle”).
Cleaning and care Cleaning the control panel The control panel should only be wiped with a damp cloth. Cleaning the reflector panel The reflector panel for the in-operation indicator light is situated on the cover sheeting underneath the countertop. The reflector panel should only be cleaned with a damp cloth if necessary. Cleaning the front of the machine Damage due to soiling.
Cleaning and care Cleaning the spray arms Removing the cutlery tray (if present) Particles of food can get stuck in the spray-arm jets and bearings. The spray arms should therefore be inspected regularly (approx. every 2–4 months). In order to be able to remove the upper spray arm, you first have to remove the cutlery tray (if present). Pull out the cutlery tray. Never run a wash program without using the spray arms. Damage due to soiling entering the circulation system.
Cleaning and care Removing the upper spray arm Removing the lower spray arm Remove the lower basket. Push the upper spray arm upward to engage the inner ratchet. Then unscrew the spray arm by rotating the screw thread counterclockwise . Removing the middle spray arm Rotate the screw thread of the lower spray arm counterclockwise and pull the spray arm upward to remove . Cleaning the spray arms Rotate the screw thread of the middle spray arm clockwise and remove the spray arm .
Cleaning and care Reinstalling the spray arms Inserting the cutlery tray (if present) Reinstall the upper spray arm and tighten it by hand. Slide the cutlery tray back onto the rails from the front. Reinstall the middle spray arm. Replace the safety clips in the rails on both sides of the cutlery tray. Reinstall the lower spray arm and ensure that the filter combination lies flat in the base of the wash cabinet.
Cleaning and care Checking the filters in the wash cabinet Cleaning the filters The filter combination in the base of the wash cabinet retains coarse soil from the suds solution. This prevents soiling getting into the circulation system and re-entering the wash cabinet through the spray arms. Remove the lower spray arm (see “Cleaning the spray arms” under “Cleaning and care”). Damage due to soiling entering Turn off the dishwasher.
Cleaning and care In order to clean the inside of the filter, pull the microfilter on the plastic ring downwards and away from the filter combination. Rinse all of the filters under running water. If necessary, use a soft cleaning brush to remove soiling. Insert the microfilter back into the filter combination. Reinstall the filter combination so that it lies flat in the base of the wash cabinet. Refit the lower spray arm to the filter combination using the screw thread.
Cleaning and care Cleaning the drain pump If water remains in the wash cabinet after the end of a program, the water has not been pumped away. The drain pump may be blocked by foreign objects. These foreign objects are easy to remove. Disconnect the dishwasher from the power supply. To do this, turn off at the electrical socket and withdraw the plug. Take the filter combination out of the wash cabinet (see “Cleaning the filters” under “Cleaning and care”).
Cleaning and care Damage due to incorrect cleaning. The components are delicate and can be damaged during cleaning. Take care when cleaning the drain pump. The drain pump (see arrow) is underneath the cover. Risk of injury from glass splinters. It is especially difficult to see glass splinters in the drain pump. Take care when cleaning the drain pump. Carefully remove all foreign objects from the drain pump. Check the drain pump impeller by manually turning it.
Frequently Asked Questions With the help of the following guide minor faults in the performance of the machine, some of which may result from incorrect operation, can be remedied without contacting the Service Department. This guide may help you to find the reason for the fault, and how to correct it. This section only lists faults that you can remedy yourself. All other faults are shown in Fault FXX. Technical faults Problem Possible cause and solution The dishwasher does not start.
Frequently Asked Questions Fault messages Problem Possible cause and solution The in-operation indica- Before remedying the fault: tor light is flashing Turn off the dishwasher. quickly. The alarm tone is sounding. One of the following faults appears in the display: Fault FXX There may be a technical fault. Turn the dishwasher back on after a few seconds. Select the desired program. Close the door. If the fault message appears again, there is a technical fault. Turn off the dishwasher.
Frequently Asked Questions Door release Problem Possible cause and solution The in-operation indica- Before remedying the fault: tor light is flashing Turn off the dishwasher. quickly. The alarm tone is sounding. The following fault is indicated via the display: Door fault The door does not open automatically. There may be a technical fault. Open the door manually (see “Opening the door” under “Before using for the first time”) and turn the dishwasher back on again.
Frequently Asked Questions Water intake fault Problem Possible cause and solution The in-operation indicator light is flashing quickly. The alarm tone is sounding. One of the following messages appears in the display: Open water supply The water supply is turned off. Open the water supply valve all the way. Intake Before remedying the fault: Turn off the dishwasher. Water-intake fault. Open the water-supply faucet all the way and start the program again.
Frequently Asked Questions Water drainage fault Problem Possible cause and solution The in-operation indicator light is flashing quickly. The alarm tone is sounding. The following message appears on the display: Drain Before remedying the fault: Turn off the dishwasher. Water drainage fault. There might be water in the wash cabinet. Clean the filter combination (see “Cleaning the filters” under “Cleaning and care”). Clean the drain pump (see “Cleaning the drain pump” under “Cleaning and care”).
Frequently Asked Questions General dishwasher problems Problem Possible cause and solution The in-operation indica- The safe mode of the dishwasher was activated. tor light is flashing This takes place in the following instances: quickly. – If you do not close the door within 4 seconds of The alarm tone is the last press of a button at program start. sounding. – If the door is open for longer than 4 seconds The indicator light of during a program or within the delay-start time.
Frequently Asked Questions Problem Possible cause and solution Water remains in the Before remedying the fault: wash cabinet at the end Turn off the dishwasher. of a program. The filter combination in the wash cabinet is clogged. Clean the filter combination (see “Cleaning the filters” under “Cleaning and care”). The drain pump is blocked. Clean the drain pump (see “Cleaning the drain pump” under “Cleaning and care”). The drain hose is kinked. Remove any kinks from the drain hose.
Frequently Asked Questions Noises Problem Possible cause and solution There is a knocking noise in the wash cabinet. A spray arm is knocking against a wash item. Carefully open the door and rearrange the wash items that are obstructing the spray arm. There is a rattling noise in the wash cabinet. Wash items are not secure in the wash cabinet. Carefully open the door and rearrange the wash items so that they sit securely. There is a foreign object (e.g., glass shard) in the drain pump.
Frequently Asked Questions Poor cleaning results Problem Possible cause and solution The dishware is not clean. The dishware was not loaded correctly. See notes under “Loading the dishwasher”. The program was not powerful enough. Select a more powerful program (see “Program overview”). Activate the Extra clean function (see “Extra clean” under “Settings”). Activate the “Second interim rinse” function (see “Settings – Second interim rinse”). Not enough detergent was dispensed.
Frequently Asked Questions Problem Possible cause and solution The dishware is not dry or utensils and glasses are flecked. The rinse-aid dosage is set too low or the rinse-aid reservoir is empty. Replenish the reservoir, increase the dosage, or change the brand of rinse aid (see “Rinse aid” under “Before using for the first time”). The dishware was taken out of the wash cabinet too soon. Leave the dishware in longer (see “Unloading the dishwasher” under “Operation”).
Frequently Asked Questions Problem Possible cause and solution Plastic parts are discol- Natural dyes, e.g., from carrots, tomatoes, or ored. ketchup may be the cause. The amount of detergent used or its bleaching effect was not sufficient to deal with natural dyes. Use more detergent (see “Detergent”). Parts that are already discolored will not revert to their original color. White residue is visible on the dishware. Clouding has occurred on glassware and utensils. The film can be wiped off.
Frequently Asked Questions Problem Possible cause and solution There are rust stains on The affected items are not corrosion resistant. the cutlery. No remedy. Purchase cutlery which is dishwasher-proof. A program was not run after reactivation salt was added. Traces of salt have got into the normal wash cycle. Always run the QuickIntenseWash program with the Express program option selected and without any dishes in the dishwasher after adding reactivation salt.
Customer Service Contact in the event of a fault In the event of a fault which you cannot remedy yourself, please contact your Miele dealer or Miele Customer Service. You can book a Miele Service Call online at www.miele.com/service. Appliance warranty and product registration You can register your product and/or view the manufacturer´s warranty terms and conditions for Miele appliances and vacuum cleaners at www.mieleusa.com.
Optional accessories Dishwasher detergent, rinse aid, and cleaning and care products are available for this dishwasher, as are optional accessories. All the products have been designed for Miele appliances. Rinse aid These and many other useful products can be ordered directly from Miele’s online store, Miele Customer Service, or from your Miele dealer.
Optional accessories Appliance care Miele cleaning and care products provide optimum care for your dishwasher.
*INSTALLATION* Installation Water intake Danger to health due to wash water. Water in the dishwasher must not be used as drinking water. Do not drink any water from the dishwasher. Health risk and risk of damage due to contaminated incoming water. The quality of the incoming water must correspond to the drinking water specification of the country in which the dishwasher is being operated. Connect the dishwasher to a drinking water supply.
*INSTALLATION* Installation A water supply with 3/8" Compression Connection (thread connection of 9/16" – 24 UNEF) must be provided on site. If this type of faucet is not available, only a qualified installer may connect the dishwasher to the domestic water supply. A back-flow preventer is not required by the manufacture, but may be required by local code regulations. The water-connection pressure needs to be between 7.25 and 145 psi (50 and 1,000 kPa).
*INSTALLATION* Installation Water drainage The appliance drainage system has a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. The dishwasher is supplied with approx. 5 ft (1.5 m) of flexible drain hose with an internal diameter of 7/8" (22 mm). The hose can be extended using a connection piece to attach a further length of hose. The drainage length must not be longer than 13 ft (4 m) and the delivery head no higher than 3 ft (1 m).
*INSTALLATION* Installation Venting the water drainage If the on-site drainage connection is situated lower than the guide path for the lower basket rollers in the open door, the drainage system must be vented. Otherwise, a siphoning effect during a program can cause the appliance to empty itself of water. Open the dishwasher door fully. Remove the lower basket. Insert a screwdriver into the middle opening of the vent valve in the left wash cabinet wall .
*INSTALLATION* Installation Electrical connection Installation, repairs and other work by unqualified persons could be dangerous. Check that the voltage, frequency and fuse rating shown on the data plate match the household power supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the electrical supply. Danger of overheating! See data plate on the right side of the door.
*INSTALLATION* Installation Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually “tripping” the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards.
Sound emission testing Prerequisites for sound emission tests Load the dishwasher with 16 standard place settings and use the Normal program. Setup for sound emission tests The dishwasher must be set up according to the following specifications. Install the dishwasher into an analyzing unit. Secure the front panel. Push the provided fleece strips (depending on model) under the toe kick until it is flush with the appliance feet .
Sound emission testing Remove the protective film from the provided insulating strip (depending on model) . Stick the insulating strip onto the front top edge of the toe-kick board .
Please have the model and serial number of your appliance available when contacting Customer Service. U.S.A. Canada Miele, Inc. Importer Miele Limited National Headquarters 9 Independence Way Princeton, NJ 08540 Customer Service & Support Phone: 888-99-MIELE(64353) info@mieleusa.com www.mieleusa.com International Headquarters Miele & Cie. KG Carl-Miele-Straße 29 33332 Gütersloh Germany Headquarters and Miele Centre 161 Four Valley Drive Vaughan, ON L4K 4V8 www.miele.
G 7151, G 7156 en-US M.-Nr.