Operating instructions Rotary iron HM 5316 To prevent accidents and machine damage read these instructions before installation or use. UV M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Guide to the rotary iron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operating panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Foot control bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before installation or use. To prevent injury and machine damage. Electrical safety Be certain this appliance is properly installed and grounded by an authorized technician. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system. It is imperative that this basic safety requirement be met and tested. Consult a qualified electrician if in doubt.
IMPORTANT SAFETY INSTRUCTIONS Do not damage, remove or bypass any of the safety features and controls of the rotary iron. Do not operate a machine with an electrical fault until repaired. Repairs to electrical appliances should only be carried out by an authorized technician in accordance with local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held responsible for unauthorized work.
Guide to the rotary iron 1 Heater plate with finger guard 2 Roller 3 Feed board 4 Operating panel 5 Laundry container 6 Cover for emergency handle insert 7 Emergency handle 8 Ironing table 9 Exhaust connector 10 Foot control bar 5
Guide to the rotary iron Operating panel Temperature selector The temperature can be increased by turning the selector clockwise. It can be decreased by turning the selector counterclockwise. ß = Low temperature ßß = Medium temperature ßßß = High temperature Roller speed selector The roller speed can be increased by turning the selector clockwise. It can be decreased by turning the selector counterclockwise. "Operating" indicator The "operating" indicator lights, when the button "I" is pressed.
Guide to the rotary iron Foot control bar 1st Switch point Steaming, the roller stops 2nd Switch point and button "O" pressed: The heater plate lowers and the roller turns. 2nd Switch point and button "P" pressed: The heater plate rises and the roller turns backwards. Only for removing the ironing cover and padding. (See "Cleaning and Care" for more information.) Finger guard ,The finger guard is a safety feature which must be checked before each use of the rotary iron.
Use Correct dampness Ironing tips For best results, the residual moisture of the laundry should be 25%. – To avoid creasing stop the roller, pull the item back slightly and smooth out. If necessary, dampen again with a wet cloth or spray bottle. Laundry which contains more than 50% synthetic fibers must not be ironed in this machine. The synthetics might melt at the high temperatures. Laundry with less synthetics can be ironed at a low temperature.
Use Ironing laundry Steaming laundry ^ Turn the unit on at the wall switch. ^ To steam laundry, press the foot pedal down to the 1st switch point. ^ Ironing with coin mechanism: Insert coins or token. ^ Press "I" to turn the iron on. ^ Select the temperature depending on the laundry with the temperature selector. ^ Press the "O" button. The heater plate lowers when a temperature of about 140°F (60°C) is reached. ^ Select a roller speed depending on dampness and type of laundry.
Frequently asked questions Power failure Protecting the roller and iron cover If there is a power failure when the iron is in use, the heater plate will stay on the roller. The item being ironed will then be held there possibly becoming scorched. If no laundry is ironed the ironing cover could be damaged. – During breaks and after ironing the heater plate should be raised. The roller and the iron cover durability will be increased. Avoid running the iron without laundry.
Cleaning and Care Regular cleaning and maintenance of the heater plate is essential for the durability of the motor and roller pad and cover. Waxing the heater plate The heater plate should be waxed daily before use with a cleaning cloth for optimum performance. Original cleaning cloths and ironing wax can be obtained from Miele. ^ For cleaning and waxing the heater plate, set the roller speed to the lowest and the temperature to ßßß.
Cleaning and Care Discoloration of the ironing cover Applying an ironing cover A slight to heavily brown coloration of the ironing cover is normal. ^ Raise the heater plate and turn the rotary iron off. To avoid the cover from turning black: ^ Lay the ironing cover on the roller (parallel). – Always use the complete roller width. – Space out smaller items, alternating from left to right. – Raise the heater plate and lower the temperature during breaks.
After sales service In the event of a problem, please contact the Miele Technical Service Department at the phone number on the back of this booklet. When contacting Technical Service please quote the model (M.-Nr.) and serial number (Fabr.-Nr.) of the machine. These can be found on the silver data plate. Only use original Miele spare parts for maintenance or repairs on this machine.
Guide to the data plate symbols 1 Machine type 15 Electric heating 2 Serial number/Year of production * 16 Fuse (on site) 3 Voltage/Frequency 17 Steam heating indirect 4 Fuse rating 18 Steam heating direct 5 Drive motor 19 Gas heating 6 Plate diameter/Plate quantity * 20 Commissioning date 7 Drum data 21 Water-Registration DVGW-test cert (Water) 8 Drum diameter/Drum depth 9 Spin speed 22 Field for CE test symbol 10 Drum volume/Laundry dry weight 11 Kinetic Energy Noise level 12 Ex.
Miele Ironing Handbook
Introduction General notes on ironing Fabrics suitable for ironing Correctly ironed laundry will be smooth, crease-free and not misshapen. However, in order to achieve this, the correct combination of mechanical energy, heat and steam is required. Different types of fabric react differently to being ironed. Cottons and linens expand when wet, and ironing at a high temperature and pressure will make these fabrics smooth, shiny and dry.
Introduction Washing items prior to ironing Cleaning and caring for heater plate The washing process is very important. Follow the manufacturers guidelines on detergent. It too much detergent is used and is not fully rinsed, residues can be left on the laundry. Regular cleaning and maintenance of the heater plate is essential for the protection of the motor and the roller cover, and helps to prolong the life of the machine.
Caring for your rotary iron Accessories for cleaning Waxing and cleaning Nomex cleaning cloth max. 284°F (140°C) For daily removal of residue and starch from the roller. At the end of the workday or as needed (to clean light deposits): apply a small quantity of Cleanpaste with a clean wax cloth. This will loosen any minor soiling overnight, and help prevent the build-up of deposits on the rotary iron. For best results, use the whole width of the iron. Cleaning mat, round-grained max.
Caring for your rotary iron How to use the cloth with pouch General notes – Use separate cloths for ironing wax and Cleanpaste. The amount and frequency of application can vary according to use, as a general rule "Less is more". – When using the cleaning cloth make sure that the maximum recommended temperature is not exceeded. Passing a cleaning cloth or wax cloth through the rotary iron Do not use abrasive cleaning materials, e.g. sand paper, to clean aluminum heater plates.
Frequently asked questions Creases and wrinkles Possible cause Starch deposits Solution – Adjust the quantity of detergent to the water hardness in your area.
Frequently asked questions Discoloration of the iron cover Possible cause Solution Brown/Dark yellow: Normal due – Clean the heater plate – Wash or replace the iron cover to heat from roller Black (striped or patches): Fibers – Use the recommended temperature for the fabric being ironed or plastics may have melted or Use only original Miele spare parts – burnt to the iron Jet-black on ends of roller which has occurred very quickly. – Check the air supply to the room.
Installation Instructions
Installation instructions Condensate trap The rotary iron should be installed by a Miele trained installer. Installation site ,Do not operate the rotary iron in a room where cleaning machines are operated with solvents containing CFC. These vapors could damage the machine. The machine does not require any special anchorage or base installation. ^ Select a location which has sufficient light for comfortable operation. Installation ^ Level the rotary iron with the 4 height adjustable feet.
Installation instructions Electrical connection ,All electrical work must be performed by a qualified service technician in accordance with all applicable codes and standards. ^ Regard the data plate, wiring diagram, conversion and installation plan. The wiring diagram is located under the cover of the right side column. The machine is supplied for 230V, 60 Hz, 3AC. ^ If converted to another voltage, mark it with D on the data plate.
Help to protect the environment Disposal of the packing materials Disposal of an old appliance The packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Old appliances may contain materials that can be recycled. Please contact your local recycling center about the possibility of recycling these materials. To prevent suffocation, ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
All rights reserved / 1806 06 858 370 / 00